Commit f6d1f6e4 broke selection of UARTs
other than UART0 for am335x_evm configurations by setting CONS_INDEX to
1 for all configurations.  Revert the CONS_INDEX changes.
Signed-off-by: NAndrew Bradford <andrew@bradfordembedded.com>

Update my email address as ti814x_evm maintainer to save
people some frustrating bounces and non-response.
Signed-off-by: NMatt Porter <matt.porter@linaro.org>

As
http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast
states:
"Initialize devices only when they are needed within U-Boot"

enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is
enabled. Enable this in ti_am335x_common.h, so all boards in mainline
should work as before.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>

If no softreset save registers are found on the hardware
"bootcount" is stored in the environment. To prevent a
saveenv on all reboots, the environment variable
"upgrade_available" is introduced. If "upgrade_available" is
0, "bootcount" is always 0 therefore no need to save the
environment on u-boot boot, if "upgrade_available" is 1 "bootcount"
is incremented in the environment and environment gets written
on u-boot start.
So the Userspace Applikation must set the "upgrade_available"
and "bootcount" variable to 0 (for example with fw_setenv),
if a boot was successfully.
Signed-off-by: NHeiko Schocher <hs@denx.de>

Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h

Convert sandbox to use common time functions.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

A weak annotation is needed in order to prevent link errors when
get_ticks is overridden. This fixes sandbox build.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

Netconsole loses the second character when used as input by
either setenv stdin nc or setenv stdin serial,nc if using CONSOLE_CONSOLE_MUX

Before a nc_send_packet() to echo the input, a check is done to see if
nc_ether is valid. If its not, it waits for an arp request and then sends
the packet (which contains the first character of line to be displayed as
output). As part of reaping the arp request, the second character is consumed.
We protect this by making the call to NetLoop(NETCONS) between
input_recursion.
Signed-off-by: NSuriyan Ramasami <suriyan.r@gmail.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

Staticize local functions in s5p serial driver.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NMinkyu Kang <mk7.kang@samsung.com>

The env export command doesn't export the first variable of the list
since commit 5a31ea04
"env grep" - reimplement command using hexport_r()
Signed-off-by: NPierre Aubert <p.aubert@staubli.com>

Let highbank users break into the autoboot script with ctrl-c.
Signed-off-by: NMark Langsdorf <mark.langsdorf@calxeda.com>

As originally implemented, setting the AUTOBOOT_KEYED config option will
prevent users from breaking into the autoboot script with ctrl-c. Restore
that option with a new config symbol.
Signed-off-by: NMark Langsdorf <mark.langsdorf@calxeda.com>

Staticize local functions in xuartlite driver.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NStefan Roese <sr@denx.de>
Tested-by: NMichal Simek <monstr@monstr.eu>

Staticize local functions in mxs_auart driver.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NMarek Vasut <marex@denx.de>

Curently memcpy copies string without null terminating char because
function strlen returns only number of characters excluding
null terminating character. Replace memcpy with strcpy.
Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
CC: Tom Rini <trini@ti.com>

Signed-off-by: NLuka Perkov <luka@openwrt.org>

Signed-off-by: NLuka Perkov <luka@openwrt.org>

Signed-off-by: NTim Harvey <tharvey@gateworks.com>

Linux Kernel abolished include/linux/config.h long time ago.
(around version v2.6.18..v2.6.19)

We don't need to provide Linux copatibility any more.

This commit deletes include/linux/config.h
and fixes source files not to include this.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

Signed-off-by: NEgbert Eich <eich@suse.com>

Signed-off-by: NEgbert Eich <eich@suse.com>

The gpt command was only implemented for mmc devices. There is no reason
why this command should not be generalized and be applied all other
storage device classes.
This change both simplifies the implementation and eliminates a
build failure for systems that don't support mmcs.
Signed-off-by: NEgbert Eich <eich@suse.com>
Tested-by: NPiotr Wilczek <p.wilczek@samsung.com>
[trini: Change coding style slightly]
Signed-off-by: NTom Rini <trini@ti.com>

This commit omits non-existing drivers/net/netarm_eth.c from the list.
This driver is deleted by commit b411eb30.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

The following serial drivers do not exist any more.

 - ns9750_serial.c: deleted by commit 4cfc611b
 - s3c4510b_uart.c: deleted by commit afad4029
 - serial_clps7111.c: deleted by commit f2e08015
 - serial_netarm.c: deleted by commit b411eb30

This commit cleans up UDM-serial.txt.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

Everytime a dead driver is removed from the list,
we must re-number. This is a painful task.

Try
  git show e5323225 -- doc/driver-model/UDM-serial.txt
  git show 6f62f420 -- doc/driver-model/UDM-serial.txt
  git show b9f4bc34 -- doc/driver-model/UDM-serial.txt
to see what I mean.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

Nowhere pass a value to len, which always 0, make no transfer which
cause uploading failed.

This patch make nand upload working. However it needs enough malloc
buffer to store read data, that means the buffer at least equal to
the upload partition size, or else it doesn't work.
Signed-off-by: NBo Shen <voice.shen@atmel.com>

add the possibility to set the iSerialNumber board specific.
Default value for iSerialNumber is 0x0. This value can
changed board specific through the new function
g_dnl_set_serialnumber() which must be called from the
board specific function g_dnl_bind_fixup().
Signed-off-by: NHeiko Schocher <hs@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: NLukasz Majewski <l.majewski@samsung.com>

After dfu buffer is initialized, the buffer should be all available,
while not 0. Initialize its value to min(dfu_buf_size, dfu->r_left).
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Tested-by: NLukasz Majewski <l.majewski@samsung.com>
Acked-by: NLukasz Majewski <l.majewski@samsung.com>

The value of dfu->r_left need decrease along with the transfer
Signed-off-by: NBo Shen <voice.shen@atmel.com>

submit_common_msg should report amount of data passed from/to device.
Instead, it always returned size requested by Host.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>

This patch allows exiting from UMS mode to u-boot prompt
by detaching usb cable or by pressing ctrl+c.

Add new config: CONFIG_USB_CABLE_CHECK. If defined then board
file should provide function: usb_cable_connected() (include/usb.h)
that return 1 if cable is connected and 0 otherwise.

Changes v2:
- add a note to the README
Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>

UMS init was implemented in trats board file but mostly it comprises
common code. Due to that it has been moved to common/ums.c to avoid
code duplication in the future.

Changes:
- move ums initialization code from trats to common/ums.c
- remove unused CONFIG_USB_GADGET_MASS_STORAGE from trats.h

Changes v2:
- move this patch at the top of code cleanups patches
Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>

This patch prevents:
- ums disk capacity miscalculation because of integer overflow

Changes v2:
- Prevents passing zero size disk capacity to ums gadget driver
- Change function ums_get_capacity() to ums_disk_init() and do ums disk
  initialization before gadget init
- Remove unnecessary code from mass storage driver
Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>

Before this change ums command only allowed use of mmc 0.
Now this argument can be set.

Changes:
- remove mmc device number checking because it is always positive number
- remove printing "no such device" - it is done by find_mmc_device()

Change-Id: I767e45151ad515c7bef19e6c13087374f5e23c11
Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>

This patch introduces some cleanups to ums code. Changes:

ums common:
- introduce UMS_START_SECTOR and UMS_NUM_SECTORS as defined in
  usb_mass_storage.h both default values as 0 if board config
  doesn't define them

common cleanup changes:
- change name of struct "ums_board_info" to "ums"
- "ums_device" fields are moved to struct ums and "dev_num" is removed
- change function name: board_ums_init to ums_init
- remove "extern" prefixes from usb_mass_storage.h

cmd_usb_mass_storage:
- change error() to printf() if need to print info message
- change return values to command_ret_t type at ums command code
- add command usage string

Changes v2:
ums common:
- always returns number of read/write sectors
- coding style clean-up
ums gadget:
- calculate amount of read/write from device returned value.
Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>

There is no CONFIG_PCA953X_INFO symbol.
U-Boot uses CONFIG_CMD_PCA953X_INFO instead, which is described in
"Monitor Functions" section and thus no need to be repeated in the
"GPIO Support" section.
Remove the whole line.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>

Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

In commit "5c427e49: use BOOTM_STATE_OS_CMDLINE flag for plain bootm"
and "3d187b39: Only pass BOOTM_STATE_OS_CMDLINE on PowerPC/MIPS",
BOOTM_STATE_OS_CMDLINE was added to do_bootm for PowerPC and MIPS. This
breaks other OSes (vxworks, netbsd, plan9,...) that don't support
subcommand processing, e.g. they all contain the following code in their
do_bootm_xxx():

    if (flag & BOOTM_STATE_OS_PREP)
            return 0;
    if ((flag != 0) && (flag != BOOTM_STATE_OS_GO))
            return 1;

which will result a "subcommand not supported" error.
This patch changes the above logic to:

    /* if not go command, pretend everything to be OK */
    if (flag != BOOTM_STATE_OS_GO)
         return 0;
Signed-off-by: NMiao Yan <miao.yan@windriver.com>

In-tree build:
  - Do not create a symbolic link
      from include/asm to arch/${ARCH}/include/asm
  - Add ${SRCTREE}/arch/arm/include into the header search path

Out-of-tree build:
  - Do not create a directory ${OBJTREE}/include2
  - Do not create a symbolic link
      from ${OBJTREE}/include2/asm to ${SRCTREE}/arch/${ARCH}/include/asm
  - Add ${SRCTREE}/arch/arm/include into the header search path
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>