- 23 1月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 05 12月, 2019 2 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Miquel Raynal 提交于
MTD must be enabled when there is a SPI NOR flash using the SPI_FLASH_MTD config entry. Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: NBoris Brezillon <boris.brezillon@bootlin.com>
-
- 21 11月, 2019 2 次提交
-
-
由 Tom Rini 提交于
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com> Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
-
由 Tom Rini 提交于
Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 08 11月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 08 10月, 2019 4 次提交
-
-
由 Troy Kisky 提交于
Add CONFIG_DM_SPI/CONFIG_DM_SPI_FLASH to all defconfigs whose board is nitrogen6x. mx6qsabrelite_defconfig nitrogen6dl2g_defconfig nitrogen6dl_defconfig nitrogen6q2g_defconfig nitrogen6q_defconfig nitrogen6s1g_defconfig Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
-
由 Troy Kisky 提交于
Add CONFIG_DM_GPIO to all defconfigs whose board is nitrogen6x. mx6qsabrelite_defconfig nitrogen6dl2g_defconfig nitrogen6dl_defconfig nitrogen6q2g_defconfig nitrogen6q_defconfig nitrogen6s1g_defconfig This is in preparation for adding CONFIG_DM_SPI. Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
-
由 Troy Kisky 提交于
Add DM_MMC to all defconfigs whose board is nitrogen6x. mx6qsabrelite_defconfig nitrogen6dl2g_defconfig nitrogen6dl_defconfig nitrogen6q2g_defconfig nitrogen6q_defconfig nitrogen6s1g_defconfig This commit is adding multiple configs, but seems to be the minimum change to not lose features and still compile fine. Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
-
由 Troy Kisky 提交于
Migrate to using device tree required for further driver model integration. Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
-
- 24 8月, 2019 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_FSL_USDHC Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 02 8月, 2019 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_USE_PREBOOT CONFIG_PREBOOT Both are together in one commit, since otherwise the former causes kconfig to define the latter, which gives duplicate symbol errors. Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the backslash lands in the wrong place. Similarly with socfpga_vining_fpga. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
- 23 6月, 2019 1 次提交
-
-
由 Yangbo Lu 提交于
Converted to use fsl_esdhc_imx for i.MX platforms. Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com> Tested-by: NSteffen Dirkwinkel <s.dirkwinkel@beckhoff.com> Reviewed-by: NPeng Fan <peng.fan@nxp.com> Reviewed-by: NLukasz Majewski <lukma@denx.de> Reviewed-by: NMartyn Welch <martyn.welch@collabora.com> Acked-by: NJason Liu <Jason.hui.liu@nxp.com>
-
- 30 4月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 14 4月, 2019 1 次提交
-
-
由 Anatolij Gustschin 提交于
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
- 26 3月, 2019 1 次提交
-
-
由 Patrick Delaunay 提交于
This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
-
- 19 1月, 2019 1 次提交
-
-
由 Philipp Tomsich 提交于
The bounce buffer is used by a few drivers (most of the MMC drivers) to overcome limitations in their respective DMA implementation. This moves the configuration to Kconfig and makes it user-selectable (even though it will be a required feature to make those drivers work): the expected usage is for drivers depending on this to 'select' it unconditionally from their respective Kconfig (see follow-up patches). This commit includes a full migration using moveconfig.py to ensure that each commit compiles. To ensure bisectability we update dependencies of various drivers to now select BOUNCE_BUFFER when needed. [trini: Squash all patches to ensure bisectability] Signed-off-by: NTom Rini <trini@konsulko.com> Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion] Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion] Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
-
- 18 8月, 2018 2 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: NAdam Ford <aford173@gmail.com> Acked-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 17 8月, 2018 1 次提交
-
-
由 Tom Rini 提交于
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 04 6月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 30 5月, 2018 1 次提交
-
-
由 Alex Kiernan 提交于
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to drivers/fastboot. Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing behaviour. Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 28 4月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: NAdam Ford <aford173@gmail.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 09 4月, 2018 2 次提交
-
-
由 Mario Six 提交于
Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Migrate the CONFIG_SYS_ALT_MEMTEST option to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc> [trini: Re-run migration after also including CMD_MEMTEST] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 24 2月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 14 2月, 2018 1 次提交
-
-
由 Tuomas Tynkkynen 提交于
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
- 11 2月, 2018 1 次提交
-
-
由 Tom Rini 提交于
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 13 12月, 2017 1 次提交
-
-
由 Tuomas Tynkkynen 提交于
Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
-
- 31 10月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 11 10月, 2017 1 次提交
-
-
由 Tuomas Tynkkynen 提交于
Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
-
- 04 10月, 2017 4 次提交
-
-
由 Maxime Ripard 提交于
Fastboot need a bunch of options to be operating properly, such as the g_dnl gadget, the fastboot command, and some options that make sense. Since fastboot is now part of Kconfig, make sure we have them right. That will also reduce the boilerplate in the defconfigs. Reviewed-by: NŁukasz Majewski <lukma@denx.de> Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Maxime Ripard 提交于
The g_dnl USB settings for the vendor ID, product ID and manufacturer are actually common settings that can and should be shared by all the gadgets. Make them common by renaming them, and convert all the users. Reviewed-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NLukasz Majewski <lukma@denx.de> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Maxime Ripard 提交于
We need to select an interface for the usb_ether gadget, and they haven't been converted to Kconfig yet. Add a choice to make sure we have an option selected, and convert all the users. Reviewed-by: NŁukasz Majewski <lukma@denx.de> Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Maxime Ripard 提交于
The USB Ethernet gadget option has not yet been moved to Kconfig, let's deal with that. Reviewed-by: NŁukasz Majewski <lukma@denx.de> Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
- 02 9月, 2017 2 次提交
-
-
由 Tom Rini 提交于
- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's not strictly part of fastboot. - Add some defaults for the fastboot buffer location and size - Migrate all options listed in cmd/fastboot/Kconfig - Cleanup the README Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
This syncs all of the currently Kconfig'd symbols out of the headers and into the defconfig files. This has two exceptions, first am335x_evm needs to be converted to DM in SPL and then it can stop undef'ing CONFIG_DM_USB. Leaving this as-is results in a build failure, and without work, run time failure. The other case is am43xx_evm.h and in turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB host mode in SPL, but still desire to have gadget mode in U-Boot proper. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 28 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 15 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 09 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Reviewed-by: NJoe Hershberger <joe.hershberger@ni.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-