Add myself as the maintainer of CZ.NIC's Turris Omnia and Turris Mox
projects.
Signed-off-by: NMarek Behún <marek.behun@nic.cz>
Reviewed-by: NStefan Roese <sr@denx.de>
Signed-off-by: NStefan Roese <sr@denx.de>

The Armada 37xx watchdog driver was recently accepted for mainline
kernel by watchdog subsystem maintainer, but the driver works a little
different than the one in U-Boot. This patch fixes this.

In the previous implementation there was a tiny period of time when the
watchdog was disabled and the system was vulnerables - this was during
pinging, which was done by disabling, setting, and enabling the counter.

Now pinging is done without disabling the watchdog. We use 2 counters:
Counter 1 is the watchdog counter - on expiry, the system is reset.
Counter 0 is used to reset Counter 1 to start counting from the set
timeout again. So Counter 1 is set to be reset on Counter 0 expiry event
event and pinging is done by forcing an immediate expiry event on
Counter 0.
Signed-off-by: NMarek Behún <marek.behun@nic.cz>
Signed-off-by: NStefan Roese <sr@denx.de>

Add gpio command to defconfig - this can be used to detect whether the
button is pressed or light LEDs.
Add DS1307 RTC driver and the date command.
Add CONFIG_WATCHDOG, so that U-Boot calls watchdog_reset.
Add CONFIG_MISC_INIT_R so that ethernet addresses are read from OTP
before network controller is initialized.
Signed-off-by: NMarek Behún <marek.behun@nic.cz>
Reviewed-by: NStefan Roese <sr@denx.de>
Signed-off-by: NStefan Roese <sr@denx.de>

DTC issues a warning because #address-cells and #size-cells properties
are not set in the mdio node.
Also add ethernet1 alias.
Also add RTC node.
Also fix USB3 regulator startup delay time.
Also fix PCI Express SERDES speed to 5 GHz (this is only cosmetic, the
speed value is not used byt the comphy driver for PCI Express, but
should be 5 GHz nonetheless).
Signed-off-by: NMarek Behún <marek.behun@nic.cz>
Reviewed-by: NStefan Roese <sr@denx.de>
Signed-off-by: NStefan Roese <sr@denx.de>

Check if Mox modules are connected in supported mode, then configure
the MDIO addresses of switch modules.
Signed-off-by: NMarek Behún <marek.behun@nic.cz>
Signed-off-by: NStefan Roese <sr@denx.de>

When SFP module is connected directly to CPU module we want the SGMII
lane speed at 1.25 Gbps.

This is a temporary solution till there is a comphy driver in the kernel
capable of changing SGMII speed at runtime.
Signed-off-by: NMarek Behún <marek.behun@nic.cz>
Reviewed-by: NStefan Roese <sr@denx.de>
Signed-off-by: NStefan Roese <sr@denx.de>

Restructure the board initialization source.
Remove the module_topology environment variable since it won't be
needed.
Signed-off-by: NMarek Behún <marek.behun@nic.cz>
Reviewed-by: NStefan Roese <sr@denx.de>
Signed-off-by: NStefan Roese <sr@denx.de>

Sync the Armada-38x device tree files with Linux 4.20-rc5. The changes
not taken are new compatible strings for the uart and nand flash
controller. The nand binding is best updated if/when the mtd/nand
infrastructure is updated.
Signed-off-by: NChris Packham <judge.packham@gmail.com>
Reviewed-by: NStefan Roese <sr@denx.de>
Signed-off-by: NStefan Roese <sr@denx.de>

The bounce buffer is used by a few drivers (most of the MMC drivers)
to overcome limitations in their respective DMA implementation.

This moves the configuration to Kconfig and makes it user-selectable
(even though it will be a required feature to make those drivers
work): the expected usage is for drivers depending on this to 'select'
it unconditionally from their respective Kconfig (see follow-up
patches).

This commit includes a full migration using moveconfig.py to ensure
that each commit compiles.  To ensure bisectability we update
dependencies of various drivers to now select BOUNCE_BUFFER when needed.

[trini: Squash all patches to ensure bisectability]
Signed-off-by: NTom Rini <trini@konsulko.com>
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion]
Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion]
Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Add TFA boot flow for more boards

Add TFA boot defconfig for ls1088a and ls2088a.
Add dts fixup for PCIe endpoint and root complex.

- Bugfix for SPI environment optimization
- Spelling fixes
- Remove some defconfigs per various maintainers
- Minor db410, bananapi r2 fixes
- Bump QEMU to v3.1.0 for most platforms

commit 9a9d66f5 ("env: add spi_flash_read_env function")

breaks Environment functionality, as it reads only
until 2 \0 are found, but fills the buffer with 0x0
instead 0xff which leads in an incorrect crc sum.

Fix: init the read buffer with 0xff instead 0x00
Signed-off-by: NHeiko Schocher <hs@denx.de>

This patch synchronizes the PDU001 board DTS file with the one used by
Linux 5.0-rc2.
Signed-off-by: NFelix Brack <fb@ltec.ch>

The am335x_evm_defconfig supports all am335x_boneblack variants. Remove
the redundant am335x_boneblack_defconfig.
Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

On this board SPI is only used to configure the SoC driving the LC TFT
display which is not used in U-Boot. Hence remove SPI support.
Signed-off-by: NFelix Brack <fb@ltec.ch>

cmd/mtd.c:447:13: warning: ‘mtd_help_text’ defined but not used [-Wunused-variable]
static char mtd_help_text[] =
            ^~~~~~~~~~~~~

When SYS_LONGHELP is not defined. After looking at how other commands
work, we should surround the whole help text (even its declaration) with
an #ifdef CONFIG_SYS_LONGHELP, since it's compiled out when calling
_CMD_HELP[1] on the help text variable argument to U_BOOT_CMD.

[1] https://elixir.bootlin.com/u-boot/latest/source/include/command.h#L181Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: NMiquel Raynal <miquel.raynal@bootlin.com>

Vexpress ca15_tc2 is failing with 3.1.0 because of QEMU issue.
When this patch is applied
https://patchwork.kernel.org/patch/10754401/
Vexpress can be also turn to newer QEMU version.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

This change enables setting up specific Qemu version or sha1 for new
targets which are added after (current) v3.0.0 version.
This changes is preparation step for adding new Xilinx Versal Virt
platform which was merge after v3.0.0.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

The single job for all Layerscape 10xx platforms is close to, and
sometimes exceeds the time limit for a single job configuration.  Break
this down into jobs for LS101x, LS104x and LS108x instead.  While in
here, in the name portion of these jobs, refer to them as NXP for ARM
and not Freescale as they've been NXP for quite some time.
Signed-off-by: NTom Rini <trini@konsulko.com>

am43xx_evm_ethboot_defconfig is not being actively used and has not been
moved to DM or DT. Also, ethboot cannot be tested on AM43xx EVM as such
due EVM limitations. Therefore delete it.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

These defconfigs don't seem be actively used any more, and have not been
moved to adapt DM or DT. Therefore delete them.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Enable DM_SPI and DM_SPI_FLASH for actively used defconfigs for
am335x_evm.
Signed-off-by: NVignesh R <vigneshr@ti.com>

bananapi r2 can be booted from sd-card and emmc
saving the environment have to choose the storage
from which the device has booted

also the offset is set to 1MB to make sure env is written
to block "user data area" between uboot and first partition

https://www.fw-web.de/dokuwiki/lib/exe/fetch.php?cache=&media=bpi-r2:boot-structure.pngSigned-off-by: NFrank Wunderlich <frank-w@public-files.de>

The last parameter is expected to be the imagefile.  Since -E is a
flag having the output name before -p will make mkimage ignore the
external offset option.
Signed-off-by: NPatrick Wildt <patrick@blueri.se>

Signed-off-by: NChris Packham <judge.packham@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NChris Packham <judge.packham@gmail.com>
Reviewed-by: NAnatolij Gustschin <agust@denx.de>
Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

Signed-off-by: NChris Packham <judge.packham@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NChris Packham <judge.packham@gmail.com>

Signed-off-by: NChris Packham <judge.packham@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NChris Packham <judge.packham@gmail.com>

Signed-off-by: NChris Packham <judge.packham@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NChris Packham <judge.packham@gmail.com>

Signed-off-by: NChris Packham <judge.packham@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NChris Packham <judge.packham@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Make system_guid const.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Pin count in APQ8016 was wrong, fix that.

Fixes: ad97051b ("mach-snapdragon: Introduce pinctrl driver")
Signed-off-by: NRamon Fried <ramon.fried@gmail.com>

Signed-off-by: NRamon Fried <ramon.fried@gmail.com>

- MIPS: mscc: various enhancements for Luton and Ocelot platforms
- MIPS: mscc: added support for Jaguar2 platform
- MIPS: optimised SPL linker script
- MIPS: bcm6368: fix restart flow issues
- MIPS: fixed CONFIG_OF_EMBED warnings for all MIPS boards
- MIPS: mt7688: small fixes and enhancements
- mmc: compile-out write support if disabled

- Fixes for CVE-2018-18440 and CVE-2018-18439
- Patch to allow disabling unneeded NAND ECC layouts
- Optimize SPI flash env read process