- 19 6月, 2019 28 次提交
-
-
由 Vabhav Sharma 提交于
LS1046AFRWY board supports LS1046A family SoCs. This patch add base support for this board. Board support's 4GB ddr memory, i2c, micro-click module,microSD card, serial console,qspi nor flash,ifc nand flash,qsgmii network interface, usb 3.0 and serdes interface to support two x1gen3 pcie interface. Signed-off-by: NCamelia Groza <camelia.groza@nxp.com> Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com> Signed-off-by: NPankit Garg <pankit.garg@nxp.com> Signed-off-by: NPramod Kumar <pramod.kumar_1@nxp.com> Signed-off-by: NRajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: NVabhav Sharma <vabhav.sharma@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Wasim Khan 提交于
During SD boot, MC firmware and DPC are copied from SD card to DDR. Size reserved between MC and DPC firmware on DDR is 1MB. If the size of MC firmware(load address 0x80000000) is more than 1 MB then part of MC firmware will be overwritten by DPC firmware (load address 0x80100000). Fix: Update the MC/DPL/DPC firmware's DDR address as per their respective addresses in SD card. Signed-off-by: NWasim Khan <wasim.khan@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Wasim Khan 提交于
During SD boot, MC firmware and DPC are copied from SD card to DDR. Size reserved between MC and DPC firmware on DDR is 1MB. If the size of MC firmware(load address 0x80000000) is more than 1 MB then part of MC firmware will be overwritten by DPC firmware (load address 0x80100000). Fix: Update the MC/DPL/DPC firmware's DDR address as per their respective addresses in SD card. Signed-off-by: NWasim Khan <wasim.khan@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Wasim Khan 提交于
Add bootcmd for IFC NOR boot and SD boot. Signed-off-by: NWasim Khan <wasim.khan@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Alex Marginean 提交于
LS1028A includes an integrated PCI bus with 11 PCI functions residing on bus 0. ECAM plus the device register space takes up 256MB of address space. Signed-off-by: NAlex Marginean <alexm.osslist@gmail.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Yinbo Zhu 提交于
Layerscape began to use two eSDHC controllers, for example, LS1012A. They are same IP block with same reference clock. This patch is to add clock support for the second eSDHC. Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Maciej Pijanowski 提交于
With this setting enabled, the on-board QSPI cannot be properly flashed. There are no error messages, but the simple write / read / compare tests fail. This is already disabled in the qspi and tfa defconfigs for the LS1046ARDB platform. Signed-off-by: NMaciej Pijanowski <maciej.pijanowski@3mdeb.com> Cc: piotr.krol@3mdeb.com Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Maciej Pijanowski 提交于
Signed-off-by: NMaciej Pijanowski <maciej.pijanowski@3mdeb.com> Cc: piotr.krol@3mdeb.com Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Maciej Pijanowski 提交于
As per LS1046A hardware manual, SGMII.9 and SGMII.10 present on lane D and lane C respectively for 0x3363 protocol. So fix serdes1 settings for ls1046a. Signed-off-by: NMaciej Pijanowski <maciej.pijanowski@3mdeb.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Ashish Kumar 提交于
Signed-off-by: NAshish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Alex Marginean 提交于
Fixes a link error on layerscape platform, linking fails with CONFIG_PCI set and CONFIG_PCI_LAYERSCAPE unset. Signed-off-by: NAlex Marginean <alexm.osslist@gmail.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Pankit Garg 提交于
Change bootcmd update logic when CONFIG_ENV_ADDR is not defined Signed-off-by: NPankit Garg <pankit.garg@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Pankit Garg 提交于
Signed-off-by: NPankit Garg <pankit.garg@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Pankit Garg 提交于
Update qspi clock configuration in TFABOOT in case of all boot sources except qspi boot source. Signed-off-by: NPankit Garg <pankit.garg@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Peng Ma 提交于
This patch is to fixed the reg read to "0" for armv7 architecture. Signed-off-by: NPeng Ma <peng.ma@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Meenakshi Aggarwal 提交于
Flushing L3 cache may need variable time depending upon cache line allocation. Coming up with a proper timeout value would be best handled by simulations under multiple scenarios in your actual system. >From the purely HN-F point of view, the flush would take ~15 cycles for a clean line, and ~22 cycles for a dirty line. For the dirty line case, there are many variables outside the HN-F that will increase the duration per line. For example, a *DBIDResp from the SN-F/SBSX, memory controller latency, SN-F/SBSX RetryAck responses, CCN ring congestion, CCN ring hops, etc, etc. The worst-case timeout would have to factor in all of these variables plus the HN-F cycles for every line in the L3, and assuming all lines are dirty In case if L3 is not flushed properly, system behaviour will be erratic, so remove timeout and add loop to check status of L3 cache. System will stuck in while loop if there is some issue in L3 cache flushing. Signed-off-by: NUdit Kumar <udit.kumar@nxp.com> Signed-off-by: NMeenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Yinbo Zhu 提交于
This patch is to enable esdhc controllers for lx2160aqds Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Yuantian Tang 提交于
Add secure boot defconfig for ls1028aqds and ls1028ardb boards. Signed-off-by: NYuantian Tang <andy.tang@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Mian Yousaf Kaukab 提交于
Default environment variable is more complete. Also scans for efi binaries for example. Signed-off-by: NMian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Mian Yousaf Kaukab 提交于
fsl-mc lazyapply command applies dpl from efi_exit_boot_services(). Status of fsl-mc node in working fdt is updated at this stage. However, an efi application like grub may already have copied the fdt. So the updates to fdt done at efi_exit_boot_services() may not be visible to the OS. Fix it by updating fdt earlier if fsl-mc lazyapply command is used. Signed-off-by: NMian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Peng Ma 提交于
Move the ecc addr from driver to dts Signed-off-by: NPeng Ma <peng.ma@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Yangbo Lu 提交于
u-boot is trying to make CONFIG_BLK as a hard requirement for DM_MMC. But now it's still not. config BLK bool "Support block devices" depends on DM default y if DM_MMC When fsl_esdhc driver was reworked for DM_MMC support, DM_MMC without CONFIG_BLK enabled wasn't considered. This patch is to fix probe issue without CONFIG_BLK enabled. Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com> Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Yangbo Lu 提交于
Layerscape began to use two eSDHC controllers, for example, LS1028A. They are same IP block with same reference clock. This patch is to add clock support for the second eSDHC. Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com> Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Peng Ma 提交于
Change sata node status to enable sata. Signed-off-by: NPeng Ma <peng.ma@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Xiaowei Bao 提交于
Add other serdes protocal support. Signed-off-by: NXiaowei Bao <xiaowei.bao@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Yinbo Zhu 提交于
Rx Compliance tests may fail intermittently at high jitter frequencies using default register values. So program register USB_PHY_RX_OVRD_IN_HI in certain sequence to make the Rx compliance test pass. Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com> Signed-off-by: NRan Wang <ran.wang_1@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Ran Wang 提交于
Enable workaround for USB erratum A-008997. Here PCSTXSWINGFULL registers has been moved to DSCR as compared to other Layerscape SoCs where it was in SCFG. Signed-off-by: NRan Wang <ran.wang_1@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Pankaj Bansal 提交于
when compiling dts file using DTC_FLAG='-@', the device tree compiler reports these warnings: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-' Fixed the node aliases to silence these warnings. Signed-off-by: NPankaj Bansal <pankaj.bansal@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
- 16 6月, 2019 4 次提交
-
-
git://git.denx.de/u-boot-efi由 Tom Rini 提交于
Pull request for UEFI sub-system for v2019.07-rc5 (2) This pull request provides bug fixes for the UEFI sub-system. The most relevant one concerns the allocation of memory at address 0. It is needed for booting Linux on several boards via bootefi, e.g. the Asus TinkerBoard. An undefined reference bug in disk/part.c related to a division is resolved.
-
-
-
由 Tom Rini 提交于
- Kconfig migrations of SPL_BOOT_xxx, SYS_LDSCRIPT, IP_DEFRAG, TFTP_BLOCKSIZE. - Typo fixes, other minor corrections.
-
- 15 6月, 2019 8 次提交
-
-
由 Bartosz Golaszewski 提交于
The setexpr shell command calls cmd_get_data_size() which is only built when CMD_DATA_SIZE is defined. We need to define CMD_DATA_SIZE if CONFIG_CMD_SETEXPR is selected or the build will fail if no other command selecting this option is enabled. Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
-
由 Tom Rini 提交于
In order to migrate this symbol to Kconfig introduce a new symbol to guard it, CONFIG_SYS_CUSTOM_LDSCRIPT. When that is set we can then provide the exact final location o the script. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
A number of boards set CONFIG_SYS_LDSCRIPT and then end up using one of the default searched LDSCRIPT paths. Remove these customizations. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
The non-CONFIG_SPL_FRAMEWORK SPL used on some PowerPC platforms have a choice between CONFIG_SPL_NAND_BOOT, CONFIG_SPL_MMC_BOOT and CONFIG_SPL_SPI_BOOT. Migrate this to Kconfig Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Andy Shevchenko 提交于
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
-
由 Simon Goldschmidt 提交于
This tool has just been added but it seems I forgot to add it to the ignore list. So to prevent the built binary being marked as unversioned, add it to the ignore list. Signed-off-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
-
由 Marek Vasut 提交于
Convert CONFIG_TFTP_BLOCKSIZE to Kconfig, update defconfigs, headers and whitelist. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Christian Gmeiner <christian.gmeiner@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
-
由 Marek Vasut 提交于
Convert CONFIG_IP_DEFRAG to Kconfig, update defconfigs, headers and whitelist. This patch is a follow-up on a patch by Christian Gmeiner with the added config/header/whitelist updates. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Reported-by: NChristian Gmeiner <christian.gmeiner@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
-