- 17 12月, 2016 13 次提交
-
-
由 Jagan Teki 提交于
Add I2C support for Engicam i.CoreM6 qdl board. icorem6qdl> i2c bus Bus 0: i2c@021a0000 Bus 1: i2c@021a4000 Bus 2: i2c@021a8000 icorem6qdl> i2c dev 2 Setting bus to 2 icorem6qdl> i2c speed 100000 Setting bus speed to 100000 Hz icorem6qdl> i2c probe Valid chip addresses: 2C icorem6qdl> i2c md 2C 0xff 00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00 .......d........ Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NHeiko Schocher <hs@denx.de>
-
由 Jagan Teki 提交于
Some I2C bus devicetree nodes, doesn't require to have gpio pinctrl so replace the dev_info to debug so the print never comes on the console and for bus that uses gpio pinctrl anyway have dev_err. Before: ------ U-Boot> i2c dev 1 Setting bus to 1 i2c bus 1 at 0x21a4000, no gpio pinctrl state. After: ------ U-Boot> i2c dev 1 Setting bus to 1 Cc: Simon Glass <sjg@chromium.org> Cc: Heiko Schocher <hs@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NHeiko Schocher <hs@denx.de>
-
由 Jagan Teki 提交于
Better to print the hex value for bus address instead of decimal, for more readbility on bus addressing. Before: ------ U-Boot> i2c dev 1 Setting bus to 1 i2c bus 1 at 35274752, no gpio pinctrl state. After: ------ U-Boot> i2c dev 1 Setting bus to 1 i2c bus 1 at 0x21a4000, no gpio pinctrl state. Cc: Simon Glass <sjg@chromium.org> Cc: Heiko Schocher <hs@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NHeiko Schocher <hs@denx.de>
-
由 Jagan Teki 提交于
Added kconfig for SYS_I2C_MXC driver. Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Jagan Teki 提交于
Add custom splashscreen, engicam.bmp support for Engicam i.CoreM6 qdl board. Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Jagan Teki 提交于
Add IPUv3 framebuffer support for Engicam i.CoreM6 qdl board. Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Jagan Teki 提交于
Added kconfig entry for CONFIG_VIDEO_IPV3 driver. Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Jagan Teki 提交于
Use CONFIG_DM_ETH and remove board_eth_init code from board files. Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com> Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Jagan Teki 提交于
Add FEC dts support for Engicam i.CoreM6 dql modules. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com> Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Jagan Teki 提交于
Add .read_rom_hwaddr on dm eth_ops. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com> Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Jagan Teki 提交于
- Remove exctra space - Add space - Add tab space - Fix single line comments quotes - Fix 'CHECK: Avoid CamelCase' - Fix 'CHECK: Alignment should match open parenthesis' - Fix 'WARNING: line over 80 characters' - Re-arrage header include files Cc: Simon Glass <sjg@chromium.org> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com> Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Jagan Teki 提交于
This patch add driver model support for fec_mxc driver. Cc: Simon Glass <sjg@chromium.org> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Jagan Teki 提交于
fec_get_hwaddr never used eth_device argument, hence removed. Cc: Simon Glass <sjg@chromium.org> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com> Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
- 16 12月, 2016 27 次提交
-
-
由 Patrick Bruenn 提交于
Add CX9020 board based on mx53loco. Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse serial_mxc with DTE and prepare for device tree migration of other functions and imx53 devices. The CX9020 differs from i.MX53 Quick Start Board by: - use uart2 instead of uart1 - DVI-D connector instead of VGA - no audio - CCAT FPGA connected to emi - enable rtc Signed-off-by: NPatrick Bruenn <p.bruenn@beckhoff.com>
-
由 Peng Fan 提交于
Add plugin support for mx6sllevk board. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
Add i.MX6SLL EVK board support. 1. Add imx6sll-evk device tree. 2. Enable SDHC/I2C/UART. 3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver. Boot Log: U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800) CPU: Freescale i.MX6SLL rev1.0 at 792MHz CPU: Commercial temperature grade (0C to 95C)Reset cause: POR Model: Freescale i.MX6SLL EVK Board Board: MX6SLL EVK DRAM: 2 GiB i2c bus 0 at 35258368, no gpio pinctrl state. PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
Add i.MX6SLL device tree. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
There two iomuxc for i.MX6SLL. One is normal IOMUXC, the other is for IOMUXC_SNVS. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Peng Fan 提交于
Update lcdif regs for i.MX6SL/SLL Signed-off-by: NYe.Li <ye.li@nxp.com> Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
Add the i.MX6SLL support to OCOTP driver. The i.MX6SLL reuses the i.MX6ULL fuse, bank 7 and bank8 have 4 words each, and there is a hole between bank 5 and bank 6. Signed-off-by: NYe Li <ye.li@nxp.com> Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
Correct loadaddr and text base for i.MX6SLL Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
add Kconfig entry for i.MX6SLL Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
If L2 cache configured as OCRAM, reset it. Switch to use runtime check. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
Add clock support for i.MX6SLL. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
The LCDIF Pixel clock mux is not glitchless, so need to gate before changing mux. Also change enable_lcdif_clock prototype with a new input parameter to indicate disable or enable. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
Add lcdif clock support for i.MX6SL. Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
The mux for the lcd clock is not glitchless, so need to first gate the clock before changing the mux. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
>From RM, per_periph2_clk_sel option3 is: "derive clock from 198MHz clock (divided 392MHz PLL2 PFD)." So fix it. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
Add iomux settings for i.MX6 SLL Signed-off-by: NPeng Fan <peng.fan@nxp.com> Signed-off-by: NYe.Li <ye.li@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
Add i.MX6 SLL GPT timer support. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
Update register address for i.MX6 SLL Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
Add i.MX6SLL pinmux header files Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
Add i.MX6SLL cpu type. MXC_CPU_MX6D is not a real value in chip, so change it to 0x6A. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Sanchayan Maity 提交于
u-boot allows modifying a device tree after it is loaded into memory. Add fdt_fixup hook in u-boot environment which can facilitate such modifications. Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
-
由 Marcin Niestroj 提交于
liteBoard is a development board which uses liteSOM as its base. Hardware specification: * liteSOM (i.MX6UL, DRAM, eMMC) * Ethernet PHY (id 0) * USB host (usb_otg1) * MicroSD slot (uSDHC1) Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
-
由 Marcin Niestroj 提交于
liteSOM is a System On Module (http://grinn-global.com/litesom/). It can't exists on its own, but will be used as part of other boards. Hardware specification: * NXP i.MX6UL processor * 256M or 512M DDR3 memory * optional eMMC (uSDHC2) Here we treat SOM similar to SOC, so we place it inside arch/arm/mach-* directory and make it possible to reuse initialization code (i.e. DDR, eMMC init) for all boards that use it. Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
-
由 Breno Lima 提交于
UDOO Neo boards has one FEC port connected to KSZ8091, add support for it. Tested on a UDOO Neo Full with "dhcp zImage" command. Signed-off-by: NBreno Lima <breno.lima@nxp.com>
-
由 Breno Lima 提交于
UDOO Neo boards has a PFUZE300 connected to I2C1 bus. Tested on a UDOO Neo Full with "pmic PFUZE3000 dump" command. Signed-off-by: NBreno Lima <breno.lima@nxp.com>
-
由 Breno Lima 提交于
Add pfuze3000 voltage configuration macro for SW1AB, SW3 and VLDO1/2 according to tables 53, 57 and 62 on PF3000 datasheet. Signed-off-by: NBreno Lima <breno.lima@nxp.com>
-
由 Breno Lima 提交于
Add thermal support on the Kconfig file. Signed-off-by: NBreno Lima <breno.lima@nxp.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-