- 10 12月, 2011 3 次提交
-
-
由 Stephen Warren 提交于
Ventana is a board which is very similar to Seaboard. Support it by re-using board/nvidia/seaboard/seaboard.c with minor run-time conditionals. v5: Makefile: Use cmd_link_o_target, remove unused clean/distclean targets. v6: Make gpio_config_uart_seaboard() static. v7: Add MAINTAINERS entry for Ventana. Tom Warren doesn't have Ventana, so he asked me to add myself for this board. Signed-off-by: NStephen Warren <swarren@nvidia.com> Acked-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Stephen Warren 提交于
Pass the GPIO numbers for power and card detect to tegra2_mmc_init(), and modify that function to perform all required GPIO initialization. This removes the need for board files to perform these operations. Move board_mmc_getcd() into tegra2_mmc.c now that the driver knows which GPIOs to use. Update affected call-sites in seaboard.c and harmony.c. Note that this change should make all SD ports work on Harmony, since the required GPIO setup is now being performed. v4: Fix prototype of tegra2_mmc_init() in board.h to match driver change. Remove prototype of gpio_config_mmc() from board.h Signed-off-by: NStephen Warren <swarren@nvidia.com> Cc: Andy Fleming <afleming@gmail.com> Tested-by: NSimon Glass <sjg@chromium.org> Acked-by: NSimon Glass <sjg@chromium.org> Acked-by: NAndy Fleming <afleming@freescale.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Stephen Warren 提交于
For Seaboard, this is mostly a cut/paste of board_mmc_init() and pin_mux_mmc() into seaboard.c; pin_mux_mmc() was modified to add some missing pinmux_tristate_disable calls for the GPIOs. For Harmony, those functions were modified to configure SDMMC2 (index 2) instead of SDMMC3 (index 1), since that's what is present on the board. However, harmony.c is still missing the required GPIO setup, so neither port is likely to function correctly yet. This will be fixed in the next change. v4: Include board.h to prototype tegra2_mmc_init(). Signed-off-by: NStephen Warren <swarren@nvidia.com> Tested-by: NSimon Glass <sjg@chromium.org> Acked-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
- 09 12月, 2011 23 次提交
-
-
由 Wolfgang Denk 提交于
During the rebase of commit 00b7d6ec "USB: Squash checkpatch warnings in usb_kbd.c" I missed a brace, resulting in a number of build errors. Fix these. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Anatolij Gustschin 提交于
Fix: da8xx_gpio.c: In function 'gpio_toggle_value': da8xx_gpio.c:208:23: warning: variable 'bank' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Daniel Schwierzeck 提交于
Build dbau1550_el only in LIST_au1xx0_el and LIST_mips_el. Also remove obsolete lists for mips5kc. Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@googlemail.com> Cc: Thomas Lange <thomas@corelatus.se>
-
由 Anatolij Gustschin 提交于
Fix: ep0.c: In function 'ep0_get_descriptor': ep0.c:187:8: warning: variable 'cp' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Acked-by: NRemy Bohmer <linux@bohmer.net> Acked-by: NMarek Vasut <marek.vasut@gmail.com>
-
由 Anatolij Gustschin 提交于
Fix: core.c: In function 'usbd_device_event_irq': core.c:596:21: warning: variable 'state' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Acked-by: NRemy Bohmer <linux@bohmer.net> Acked-by: NMarek Vasut <marek.vasut@gmail.com>
-
由 Anatolij Gustschin 提交于
Fix: musb_udc.c: In function 'musb_peri_softconnect': musb_udc.c:166:14: warning: variable 'intrtx' set but not used [-Wunused-but-set-variable] musb_udc.c:166:6: warning: variable 'intrrx' set but not used [-Wunused-but-set-variable] musb_udc.c:165:5: warning: variable 'intrusb' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Acked-by: NRemy Bohmer <linux@bohmer.net> Acked-by: NMarek Vasut <marek.vasut@gmail.com>
-
由 Anatolij Gustschin 提交于
Fix: ehci-mxc.c: In function 'ehci_hcd_init': ehci-mxc.c:113:6: warning: variable 'tmp' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Simon Glass 提交于
Sorry if this is already fixed somewhere - I could not find it. This fixes these warnings: usb_ohci.c: In function 'submit_control_msg': usb_ohci.c:1081: warning: dereferencing pointer 'data_buf.76' does break strict-aliasing rules usb_ohci.c:1081: note: initialized from here usb_ohci.c:1084: warning: dereferencing pointer 'data_buf.76' does break strict-aliasing rules usb_ohci.c:1084: note: initialized from here usb_ohci.c:1087: warning: dereferencing pointer 'data_buf.76' does break strict-aliasing rules usb_ohci.c:1087: note: initialized from here Signed-off-by: NSimon Glass <sjg@chromium.org> Acked-by: NMike Frysinger <vapier@gentoo.org>
-
由 Marek Vasut 提交于
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Denk <wd@denx.de> Acked-by: NMike Frysinger <vapier@gentoo.org> Rebased to current code. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Bernhard Kaindl 提交于
This fixes the build of the two sh boards shmin and r7780mp and qemu-mips which currently fail to build due to dropped pre-CONFIG_NET_MULTI code. This v2 patch minimizes the number of lines in the diff for easy review and to eliminate any possible accidential changes resulting from moving lines of code in the file. This also makes the register function very easy. Any cleanups and improvements are intentionally deferred to follow-up patches to keep this patch as simple and as easy to review as possible. A new driver register function, ne2k_register() calls the existing one-time setup part of the old init function and calls eth_register(). Changes to shmin, r7780mp and qemu-mips: - Call the new ne2k_register() from board_eth_init() of the boards. - Tested using qemu-mips board, - Tested the two renesas / sh boards r7780mp and shmin to compile again, and should work. checkpatch-clean when "--ignore VOLATILE" is added to .checkpatch.conf, and no warnings introduced in none of the three boards using this driver. Signed-off-by: NBernhard Kaindl <bernhard.kaindl@gmx.net>
-
由 Wolfgang Denk 提交于
Fix: inca-ip_sw.c: In function 'inca_switch_init': inca-ip_sw.c:210:6: warning: variable 'v' set but not used [-Wunused-but-set-variable] Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Fix: board.c: In function 'board_init_r': board.c:262:8: warning: unused variable 's' [-Wunused-variable] (raised for configurations without ethernet support like vct_premium_small) Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
-
由 Wolfgang Denk 提交于
Fix all errors and all warnings except for "externs should be avoided" which could require more extensive changes. Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
-
git://git.denx.de/u-boot-nand-flash由 Wolfgang Denk 提交于
* 'master' of git://git.denx.de/u-boot-nand-flash: nand_spl/nand_boot.c: Fix build warning drivers/mtd/nand/nand_spl_load.c: Fix GCC 4.6 warning drivers/mtd/nand/nand_spl_simple.c: Fix GCC 4.6 warnings
-
由 Wolfgang Denk 提交于
Fix: vpd.c: In function 'vpd_is_valid': vpd.c:168:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] vpd.c:169:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] vpd.c:178:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] vpd.c: In function 'vpd_get_data': vpd.c:281:6: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] vpd.c:291:6: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] vpd.c:297:6: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] vpd.c:302:6: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Accept 2 warnings "externs should be avoided". Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Fix: flash.c: In function 'flash_init': flash.c:47:25: warning: variable 'base_b1' set but not used [-Wunused-but-set-variable] Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
No full cleanup was attempted. Warnings about "Use of volatile is usually wrong" were ignored. One line > 80 char was intentionally accepted. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Fix: fpga.c: In function 'fpgaDownload': fpga.c:68:29: warning: variable 'val' set but not used [-Wunused-but-set-variable] Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Just reformated the code. No attempts were made to clean up warnings about "Use of volatile is usually wrong" or "externs should be avoided". Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
The "rmu" board has long been unmaintained, and is broken. Remove it. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
The OXC board has long been unmaintained, and is broken. Remove it. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
The BAB7xx boards are almost deceased. They cause build warnings, an it's not worth the effort to fix these. Remove the dead body. Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Frank Gottschling <fgottschling@eltec.de>
-
- 08 12月, 2011 8 次提交
-
-
由 Anatolij Gustschin 提交于
Fix: nand_boot.c: In function 'nand_read_page': nand_boot.c:150:6: warning: variable 'stat' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de> Signed-off-by: NScott Wood <scottwood@freescale.com>
-
由 Kyle Moffett 提交于
Standard Debian powerpc and powerpcspe systems only include hard-float libgcc in their native compilers, which causes scary build warnings when building U-Boot. Debian and other PowerPC-supporting distributions used to provide libgcc and other libraries in a "nof" (soft-float) form in the "multilib" packages. As they were completely unused by the distribution and therefore tended to be very buggy it was decided to save some time on the part of the maintainers and build-servers by removing them. Admittedly, right now the linker warnings do not indicate any problems, as the included routines do not use any floating point at all. The concern is that if floating-point code were ever added it might cause hard-float code to be unexpectedly included in U-Boot without generating a hard error. This would cause unexplained crashes or indeterminate results at runtime. The easiest way to resolve this is to borrow the routines that U-Boot needs from the Linux kernel, which has the same issue. Specifically, the routines are: _ashldi3(), _ashrdi3(), and _lshrdi3(). They were borrowed from arch/powerpc/kernel/misc_32.S as of v2.6.38-rc5, commit 85e2efbb1db9a18d218006706d6e4fbeb0216213, and are GPLv2+. The Makefile framework was copied from the U-Boot ARM port. Signed-off-by: NKyle Moffett <Kyle.D.Moffett@boeing.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: Andy Fleming <afleming@gmail.com> Cc: Kumar Gala <kumar.gala@freescale.com> Cc: Stefan Roese <sr@denx.de>
-
由 Anatolij Gustschin 提交于
Fix: nand_spl_load.c: In function 'nand_boot': nand_spl_load.c:31:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Scott Wood <scottwood@freescale.com> Acked-by: NHeiko Schocher <hs@denx.de> Acked-by: NMarek Vasut <marek.vasut@gmail.com> Signed-off-by: NScott Wood <scottwood@freescale.com>
-
由 Anatolij Gustschin 提交于
Fix warnings for both cases: definded CONFIG_SYS_NAND_HW_ECC_OOBFIRST: nand_spl_simple.c: In function 'nand_read_page': nand_spl_simple.c:156:6: warning: variable 'stat' set but not used [-Wunused-but-set-variable] not definded CONFIG_SYS_NAND_HW_ECC_OOBFIRST: nand_spl_simple.c: In function 'nand_read_page': nand_spl_simple.c:196:6: warning: variable 'stat' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Scott Wood <scottwood@freescale.com> Acked-by: NHeiko Schocher <hs@denx.de> Acked-by: NMarek Vasut <marek.vasut@gmail.com> Signed-off-by: NScott Wood <scottwood@freescale.com>
-
git://git.denx.de/u-boot-mpc83xx由 Wolfgang Denk 提交于
* 'master' of git://git.denx.de/u-boot-mpc83xx: powerpc/83xx: fix sdram initialization for keymile boards powerpc/mpc83xx: cleanup makefile for mpc83xx
-
由 Anatolij Gustschin 提交于
Fix: cfb_console.c:371: warning: 'cursor_state' defined but not used cfb_console.c:372: warning: 'old_col' defined but not used cfb_console.c:373: warning: 'old_row' defined but not used cfb_console.c:435: warning: 'video_invertchar' defined but not used Signed-off-by: NAnatolij Gustschin <agust@denx.de> Tested-by: NWolfgang Denk <wd@denx.de>
-
由 Matthias Fuchs 提交于
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu>
-
由 Stefan Roese 提交于
As this "driver" doesn't seem to be really used, let's remove it completely. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 07 12月, 2011 6 次提交
-
-
git://git.denx.de/u-boot-arm由 Wolfgang Denk 提交于
* 'master' of git://git.denx.de/u-boot-arm: davinci: Remove unwanted memsize.c from hawkboard's nand spl build devkit8000: Move CONFIG_SYS_TEXT_BASE out of bss da850evm: pass board revision info to kernel arch/arm/include/asm/arch-omap5/clocks.h: Fix GCC 4.2 warnings arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix GCC 4.6 warnings arch/arm/cpu/armv7/omap-common/spl.c: Fix GCC 4.2 warnings MX35: flea3: changes due to hardware revision B MX: serial_mxc: cleanup removing nasty #ifdef M28: Fix OB1 bug in GPIO driver MXS: Add static annotations to dma driver apbh_dma: return error value on timeout Efika: Configure additional regulators for HDMI output mx5: Correct a warning in clock.c MC13892: Add REGMODE0 bits definitions mx51evk: Configure the pins as GPIOs prior to using gpio_get_value mx53smd: Configure the pins as GPIOs prior to using gpio_get_value mx53evk: Configure the pins as GPIOs prior to using gpio_get_value mx53ard: Configure the pins as GPIOs prior to using gpio_get_value mx53loco: Configure the pins as GPIOs prior to using gpio_get_value OMAP3: Add SPL_BOARD_INIT hook AM3517 CraneBoard: Add SPL support AM3517: Add SPL support OMAP3: Add SPL support to omap3_evm OMAP3: Add SPL support to Beagleboard OMAP3 SPL: Add identify_nand_chip function OMAP3 SPL: Rework memory initalization and devkit8000 support OMAP3: Suffix all Micron memory timing parts with their speed OMAP3: Add optimal SDRC autorefresh control values omap3: mem: Add MCFG helper macro OMAP3: Remove get_mem_type prototype OMAP3: Change mem_ok to clear again after reading back OMAP3: Add a helper function to set timings in SDRC OMAP3: Update SDRC dram_init to always call make_cs1_contiguous() omap3: mem: Comment enable_gpmc_cs_config more ARM: davici_emac: Fix condition for number of phy detects arm: printf() is not available in some SPL configurations arm, davinci: add support for am1808 based enbw_cmc board arm, davinci: move misc function in arch tree arm, board/davinci/common/misc.c: Codingstyle cleanup arm, davinci, da850: add uart1 tx rx pinmux config arm, davinci: move davinci_rtc struct to hardware.h arm, davinci: Remove duplication of pinmux configuration code arm, hawkboard: Use the pinmux configurations defined in the arch tree arm, da850evm: Use the pinmux configurations defined in the arch tree arm, da850: Add pinmux configurations to the arch tree arm, da850evm: Do pinmux configuration for EMAC together with other pinmuxes arm, hawkboard: Remove obsolete struct pinmux_config i2c_pins arm, davinci: Move pinmux functions from board to arch tree arm, arm926ejs: always do cpu critical inits omap_gpmc: use SOFTECC in SPL if it's enabled nand_spl_simple: add support for software ECC AM3517: move AM3517 specific mux defines to generic header AM35xx: add EMAC support davinci_emac: hardcode 100Mbps for AM35xx and RMII davinci_emac: fix for running with dcache enabled arm926ejs: add noop implementation for dcache ops davinci_emac: conditionally compile specific PHY support davinci_emac: use internal addresses in buffer descriptors davinci_emac: move arch-independent defines to separate header BeagleBoard: config: Really switch to ttyO2 ARM: davinci_dm6467Tevm: Fix build breakage ARM: OMAP: Remove STACKSIZE for IRQ and FIQ if unused ARM: OMAP3: Remove unused define SDRC_R_C_B ARM: OMAP3: Remove unused define CONFIG_OMAP3430 omap4: fix IO setting omap4+: streamline CONFIG_SYS_TEXT_BASE and other SDRAM addresses omap4460: add ES1.1 identification omap4: emif: fix error in driver omap: remove I2C from SPL omap4460: fix TPS initialization omap: fix cache line size for omap3/omap4 boards omap4: ttyO2 instead of ttyS2 in default bootargs omap: Improve PLL parameter calculation tool start.S: remove omap3 specific code from start.S armv7: setup vector armv7: include armv7/cpu.c in SPL build armv7: disable L2 cache in cleanup_before_linux() arm, arm926ejs: Fix clear bss loop for zero length bss PXA: Move colibri_pxa270 to board/toradex/ PXA: Flip colibri_pxa27x to pxa-common.h PXA: Introduce common configuration header for PXA PXA: Rename pxa_dram_init to pxa2xx_dram_init PXA: Squash extern pxa_dram_init() PXA: Export cpu_is_ and pxa_dram_init functions PXA: Cleanup Colibri PXA270 PXA: Replace timer driver PXA: Add cpuinfo display for PXA2xx PXA: Separate PXA2xx CPU init PXA: Rename CONFIG_PXA2[57]X to CONFIG_CPU_PXA2[57]X PXA: Unify vpac270 environment size PXA: Enable command line editing for vpac270 PXA: Adapt Voipac PXA270 to OneNAND SPL PXA: Drop Voipac PXA270 OneNAND IPL PXA: Fixup PXA25x boards after start.S update PXA: Re-add the Dcache locking as RAM for pxa250 PXA: Rework start.S to be closer to other ARMs PXA: Drop XM250 board PXA: Drop PLEB2 board PXA: Drop CRADLE board PXA: Drop CERF250 board Fix regression in SMDK6400 nand: Add common functions to linux/mtd/nand.h Ethernut 5 board support net: Armada100: Fix compilation warnings ARM: remove duplicated code for LaCie boards ARM: add support for LaCie 2Big Network v2 mvsata: fix ide_preinit for missing disks netspace_v2: Read Ethernet MAC address from EEPROM omap3evm: Add support for EFI partitions part_efi: Fix compile errors
-
git://git.denx.de/u-boot-mpc85xx由 Wolfgang Denk 提交于
* 'master' of git://git.denx.de/u-boot-mpc85xx: p2041rdb: fix serdes clock map
-
git://git.denx.de/u-boot-video由 Wolfgang Denk 提交于
* 'master' of git://git.denx.de/u-boot-video: video: cfb_console: Make the software cursor non-destructive
-
由 Vadim Bendebury 提交于
TPM (Trusted Platform Module) is an integrated circuit and software platform that provides computer manufacturers with the core components of a subsystem used to assure authenticity, integrity and confidentiality. This driver supports version 1.2 of the TCG (Trusted Computing Group) specifications. The TCG specification defines several so called localities in a TPM chip, to be controlled by different software layers. When used on a typical x86 platform during the firmware phase, only locality 0 can be accessed by the CPU, so this driver even while supporting the locality concept presumes that only locality zero is used. This implementation is loosely based on the article "Writing a TPM Device Driver" published on http://ptgmedia.pearsoncmg.com Compiling this driver with DEBUG defined will generate trace of all accesses to TMP registers. This driver has been tested and is being used in three different functional ChromeOS machines (Pinetrail and Sandy Bridge Intel chipsets) all using the same Infineon SLB 9635 TT 1.2 device. A u-boot cli command allowing access to the TPM was also implemented and is being submitted as a second patch. Change-Id: I22a33c3e5b2e20eec9557a7621bd463b30389d73 Signed-off-by: NVadim Bendebury <vbendeb@chromium.org> CC: Wolfgang Denk <wd@denx.de>
-
由 Simon Glass 提交于
It is fine to use __maybe_unused instead of #ifdef, but we also need one for print_eth() since not all boards have Ethernet. This fixes this warning: cmd_bdinfo.c:39:13: warning: 'print_eth' defined but not used [-Wunused-function] Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
The spi.h include is no longer included in exports.h, so must be included here. This fixes these errors: In file included from exports.c:41:0: /home/sjg/trunk/src/third_party/u-boot/files/include/_exports.h: In function 'jumptable_init': /home/sjg/trunk/src/third_party/u-boot/files/include/_exports.h:27:1: error: 'spi_init' undeclared (first use in this function) /home/sjg/trunk/src/third_party/u-boot/files/include/_exports.h:27:1: note: each undeclared identifier is reported only once for each function it appears in /home/sjg/trunk/src/third_party/u-boot/files/include/_exports.h:28:1: error: 'spi_setup_slave' undeclared (first use in this function) /home/sjg/trunk/src/third_party/u-boot/files/include/_exports.h:29:1: error: 'spi_free_slave' undeclared (first use in this function) /home/sjg/trunk/src/third_party/u-boot/files/include/_exports.h:30:1: error: 'spi_claim_bus' undeclared (first use in this function) /home/sjg/trunk/src/third_party/u-boot/files/include/_exports.h:31:1: error: 'spi_release_bus' undeclared (first use in this function) /home/sjg/trunk/src/third_party/u-boot/files/include/_exports.h:32:1: error: 'spi_xfer' undeclared (first use in this function) Signed-off-by: NSimon Glass <sjg@chromium.org>
-