- 07 7月, 2020 33 次提交
-
-
由 Patrick Delaunay 提交于
In the boot command used in ST boards, bootcmd_stm32mp, only support the SD card as second stage, where is found the bootfs with DISTRO. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
As debugger must be totally closed on Sec closed chip, the DBGMCU_IDC register is no more accessible (self hosted debug is disabled with OTP). This patch adds a function bsec_dbgswenable() to check if the DBGMCU registers are available before to access them: BSEC_DENABLE.DBGSWENABLE = self hosted debug status. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Add "Device Name" in iproduct during DFU USB enumeration to have this information in STM32CubeProgrammer trace (this tools is compatible with @Name since v2.3) Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
With TEE 3.7.0, the partition teed (OP-TEE pageable code and data) need to increase up to 512KB in NOR device. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Activate the command env erase to reset the environment with the command: > env erase it is simpler than: > env default -a > env save Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Fabrice Gasnier 提交于
There maybe an overshoot: - when disabling, then re-enabling vrefbuf too quickly - or upon platform reset as external capacitor maybe slow discharging (VREFBUF is HiZ at reset by default). VREFBUF is used by ADC/DAC on some boards. An overshoot on the reference voltage make the conversions inaccurate for a short period of time. So: - Don't put the VREFBUF in HiZ when disabling, to force an active discharge. - Enforce a 1ms OFF/ON delay, also upon reset Penalty is a 1ms delay is applied (even for a cold boot), when enabling VREFBUF. Fixes: 93cf0ae7 ("power: regulator: Add support for stm32-vrefbuf") Signed-off-by: NFabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com> Reviewed-by: NJaehoon Chung <jh80.chung@samsung.com>
-
由 Patrick Delaunay 提交于
As kernel v5.6 have a solution since so we will be able to enable the watchdog at boot time. It is reloaded by the watchdog framework (if CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED is set) and until the userspace watchdog daemon takes over control. Need presence of kernel patch 85fdc63fe256 ("drivers: watchdog: stm32_iwdg: set WDOG_HW_RUNNING at probe") integrated in v5.6-rc1. This patch revert the previous commit ca351e70 ("stm32mp1: deactivate WATCHDOG in defconfig"). Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Add information on pin configuration used for pinmux command: - bias configuration for output (disable, pull up, pull down) - otype for input (open drain or push pull) Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Add information on pin configuration used for pinmux command. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Add support of ops get_dir_flags() to read dir flags from STMFX registers. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Manage the flags for GPIO configuration: - open_drain, push_pull - pull_up, pull_down Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Add the helper functions stmfx_read_reg() and stmfx_write_reg() to avoid duplicated code for access to stmfx's register with mask. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Rename the two function used to change the pin configuration from stmfx_pinctrl_.. stmfx_conf_... to clarify the function usage. No functional change. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Move the functions stmfx_pinctrl_set_pupd and stmfx_pinctrl_set_type; they can be used by the new ops get_dir_flags and set_dir_flags introduced by next patch. No functional change. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Add ops get_dir_flags() to read dir flags from GPIO registers. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Manage flags for GPIO configuration: - open_drain, open_source, push_pull - pull_up, pull_down Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
This patch updates the current gpio hog implementation and uses the new API gpio_hog_probe_all(), activated with CONFIG_GPIO_HOG. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
This patch activates the new configuration CONFIG_GPIO_HOG. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Move the debug function board_debug_uart_init in spl.c as the debug_uart_init() function is called in arch_cpu_init() only for SPL and remove the board.c file. For TFABOOT, the UART TX pin configuration is done in TF-A. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
This patch allows to switch the CPU frequency to 800MHz on the ST Microelectronics board (DK1/DK2 and EV1) or dh electronics SOM using the STM32MP15x SOC and when it is supported by the HW (for STM32MP15xD and STM32MP15xF). Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
For board using STPMIC1, the vddcore is provided by BUCK1 of STPMIC1 and need to be updated for 800MHz support and only after the clock tree initialization. The VDDCORE voltage value is provided by clock driver, saved in global variable opp_voltage_mv and udpated in SPL board_early_init_f(), just after clock tree initialization. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Add a function stmpic_init to early initialize the PMIC STPMIC1 - keep vdd on during the reset cycle (to avoid issue when backup battery is absent) - Check if debug is enabled to program PMIC according to the bit This patch allows to remove the compilation of spl.c file from stm32mp1 board in dh_stm32mp1. CONFIG_SPL_BOARD_INIT is removed as the new function is called earlier in SPL, in the function board_early_init_f. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Add a weak functions to save the vddcore voltage value provided in the OPP node when the clock tree is initialized. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
The PLL1 node (st,pll1) is optional in device tree, the max supported frequency define in OPP node is used when the node is absent. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Move function board_ddr_power_init() in a new file stpmic1 in board/st/common to avoid duplicated code in each board using stpmic1 Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
This commit adds cpufreq support on stm32mp15x SOC. STM32 cpufreq uses operating points V2 bindings (no legacy). Nvmem cells have to be used to know the chip version and then which OPPs are available. Note that STM32 cpufreq driver is mainly based on "cpufreq-dt" driver. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Add the bsec driver in SPL, as it is needed by SOC part number detection to found the supported OPP. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Update the compatible associated with the STM32 MPU glue in the DWC ethernet driver. The supported compatible is the specific "st,stm32mp1-dwmac" as indicated in Linux binding Documentation/devicetree/bindings/net/stm32-dwmac.txt and not the "snps,dwmac-4.20a" only used to the select IP version. This glue is implemented in Linux kernel in: drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c For information in stm32mp151.dtsi, the 2 compatibles are supported: ethernet0: ethernet@5800a000 { compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a"; ... }; Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Tom Rini 提交于
As part of merging the next branch in to master, the sifive_fu540 will fail to link: riscv64-linux-ld.bfd: lib/built-in.o: in function `panic_finish': lib/panic.c:28: undefined reference to `do_reset' make[2]: *** [spl/u-boot-spl] Error 1 make[1]: *** [spl/u-boot-spl] Error 2 make: *** [sub-make] Error 2 And while the "fix the build" option of enabling CONFIG_SPL_SYSRESET may solve the issue, it is unclear that it is the correct path exactly. For the moment, I am reverting this commit and take a "revert the revert" and proper fix as soon as it's available. This reverts commit cdae4464. Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Anup Patel <anup.patel@wdc.com> Cc: Atish Patra <atish.patra@wdc.com> Cc: Bin Meng <bin.meng@windriver.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Patrick Delaunay 提交于
This patch restores CONFIG_VIDCONSOLE_AS_LCD as boolean and introduce a separate sting as CONFIG_VIDCONSOLE_AS_NAME to search this string in stdout used as videoconsole. This patch avoid issue with board defconfig or code expecting CONFIG_VIDCONSOLE_AS_LCD as boolean. Fixes: 22b897a1 ("video: extend stdout video console work-around for 'vga'") Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
-
由 Tom Rini 提交于
Merge all outstanding changes from the current next branch in now that we have released.
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 06 7月, 2020 2 次提交
-
-
https://gitlab.denx.de/u-boot/custodians/u-boot-efi由 Tom Rini 提交于
Pull request for UEFI sub-system for efi-2020-10-rc1 This series comprises error corrections for the UEFI subsystem: * correct consideration of timestamps for variable authentication * correct collection of data regions for code authentication * correct unit tests to test loading dbx * enable FAT_WRITE as required by the UEFI spec The boot manager uses log functions instead of printf() and debug(). The UEFI intialization state is exported.
-
由 Tom Rini 提交于
- Resync Kconfiglib with the v14.1.0 release. - Re-sync our <linux/compiler*h> files with v5.7-rc5 from upstream. - Fully resync checkpatch.pl with v5.7 release. To safely to all of the above, we have a few bugfixes about functions that need a 'static inline' but weren't. We also stop setting CROSS_COMPILE in arch/*/config.mk. Finally, with the above changes boards can now opt-in to optimizing inlining and we do this for the socfpga stratix10 platform for space savings.
-
- 05 7月, 2020 3 次提交
-
-
由 Tom Rini 提交于
- Merge a fix to the gpio uclass and a test for it.
-
由 Heiko Schocher 提交于
currently gpio hog function is not tested with "ut dm gpio" so add some basic tests for gpio hog functionality. For this enable GPIO_HOG in sandbox_defconfig, add in DTS some gpio hog entries, and add testcase in "ut dm gpio" command. Signed-off-by: NHeiko Schocher <hs@denx.de> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Heiko Schocher 提交于
save the GPIOD_ flags also in the gpio descriptor. Signed-off-by: NHeiko Schocher <hs@denx.de> Reviewed-by: NPatrick Delaunay <patrick.delaunay@st.com> Fixes: 788ea834 ("gpio: add function _dm_gpio_set_dir_flags") Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NWalter Lozano <walter.lozano@collabora.com>
-
- 04 7月, 2020 2 次提交
-
-
由 Heinrich Schuchardt 提交于
The UEFI spec requires support for the FAT file system. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Heinrich Schuchardt 提交于
Export the UEFI sub-system initialization state. This will allow to treat the setting of UEFI variables during and after initialization differently. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-