- 13 6月, 2009 2 次提交
-
-
由 Peter Tyser 提交于
The following individual I2C commands have been removed: imd, imm, inm, imw, icrc32, iprobe, iloop, isdram. The functionality of the individual commands is still available via the 'i2c' command. This change only has an impact on those boards which did not have CONFIG_I2C_CMD_TREE defined. Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
-
由 Peter Tyser 提交于
Add standard CONFIG_SYS_I2C_SPEED define for the mpc7448hpc2 so that it can use the common 'i2c speed' command. Note that the I2C controller utilized by the mpc7448hpc2 has a fixed speed and cannot be changed dynamically. Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
-
- 12 6月, 2009 2 次提交
-
-
由 Haiying Wang 提交于
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com> Signed-off-by: NYu Liu <Yu.Liu@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Haiying Wang 提交于
- Increase the size of malloc to 512KB because MPC8569MDS needs more memory for malloc to support up to eight Ethernet interfaces. - Move Environment address out of uboot thus the saved environment variables will not be erased after u-boot is re-programmed. Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 10 6月, 2009 4 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Remove "saveenv" from "update" definition: the environment is outside the U-Boot image on TQM85xx and therefor not affected by updates. Also "beautify" code a bit (vertical alignment). Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Old TQM85xx boards had 'M' type Spansion Flashes from the S29GLxxxM series while new boards have 'N' type Flashes from the S29GLxxxN series, which have bigger sectors: 2 x 128 instead of 2 x 64 KB. We now change the configuration to the new flash types for all boards; this also works on old boards - we just waste two flash sectors for the environment which could be smaller there. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Dave Liu 提交于
The SYS_CLK_IN of MPC8569MDS is 66.66MHz, The DDR_CLK_IN is same with SYS_CLK_IN in 8569 processor. so, change the SYS_CLK_IN from 66MHz to 66.66MHz. Signed-off-by: NDave Liu <daveliu@freescale.com>
-
- 09 6月, 2009 1 次提交
-
-
由 Remy Bohmer 提交于
Some boards do not have SROM support for the DM9000 network adapter. Instead of listing these board names in the driver code, make this option configurable from the board config file. It also removes a build warning for the at91sam9261ek board: 'dm9000x.c:545: warning: 'read_srom_word' defined but not used' And it repaires the trizepsiv board build which was broken around the same routines Signed-off-by: NRemy Bohmer <linux@bohmer.net> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
- 08 6月, 2009 1 次提交
-
-
由 Kim Phillips 提交于
In GMII mode (which operates at 3.3V) both SICRH TSEC1/2 output buffer impedance bits should be clear, i.e., SICRH[TSIOB1] = 0 and SICRH[TSIOB2] = 0. SICRH[TSIOB1] was erroneously being set high. U-Boot always operated this PHY interface in GMII mode. It is assumed this was missed in the clean up by the original board porters, and copied along to the TQM and sbc boards. Signed-off-by: NKim Phillips <kim.phillips@freescale.com> Acked-by: NIra Snyder <iws@ovro.caltech.edu> Reviewed-by: NDavid Hawkins <dwh@ovro.caltech.edu> Tested-by: NPaul Gortmaker <paul.gortmaker@windriver.com> CC: Dave Liu <DaveLiu@freescale.com>
-
- 26 5月, 2009 1 次提交
-
-
由 Graf Yang 提交于
The pins for async memory where parallel flash lives are not enabled by default, so make sure we mux them as needed. Signed-off-by: NGraf Yang <graf.yang@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 21 5月, 2009 1 次提交
-
-
由 Kim Phillips 提交于
Configuring for TQM834x board... cpu_init.c: In function 'cpu_init_f': cpu_init.c:262: warning: array subscript is above array bounds cpu_init.c:263: warning: array subscript is above array bounds cpu_init.c:270: warning: array subscript is above array bounds ... Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
- 16 5月, 2009 3 次提交
-
-
由 Detlev Zundel 提交于
Signed-off-by: NDetlev Zundel <dzu@denx.de>
-
由 Rohit Hagargundgi 提交于
Add CONFIG_SYS_MONITOR_LEN macro to apollon board config. CONFIG_SYS_MONITOR_LEN defines the U-Boot image size. and is used by OneNAND ipl when reading U-Boot image. Signed-off-by: Rohit Hagargundgi <h.rohit at samsung.com> Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
-
由 Detlev Zundel 提交于
The pin which was used in preliminary versions of the board for ide reset is really connected to the rtc clock. Signed-off-by: NDetlev Zundel <dzu@denx.de>
-
- 06 5月, 2009 1 次提交
-
-
由 Mike Frysinger 提交于
The BF527-EZKIT settings for storing the environment in SPI flash wasn't using the correct sector settings for the SPI flash part that is actually on the board. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 01 5月, 2009 1 次提交
-
-
由 Manikandan Pillai 提交于
Signed-off-by: NDirk Behme <dirk.behme@googlemail.com> Signed-off-by: NManikandan Pillai <mani.pillai@ti.com>
-
- 30 4月, 2009 3 次提交
-
-
由 Ladislav Michl 提交于
Let CONFIG_SYS_HZ to have value of 1000 effectively fixing all users of get_timer. Changes since original version: * Set PTV=2 (divisor 8) for boards using 12MHz timer clock source to improve timer resolution. Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
-
由 Dirk Behme 提交于
Remove remaining legacy NAND defines for Beagle, EVM, Overo and Pandora. Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
由 Sanjeev Premi 提交于
Use the functions print_cpuinfo() and checkboard() to display the cpu and board specific information. These functions reuse content from the existing function display_board_info() - which has been removed. Also, updated the existig OMAP3 configurations to define: - CONFIG_DISPLAY_CPUINFO - CONFIG_DISPLAY_BOARDINFO Signed-off-by: NSanjeev Premi <premi@ti.com>
-
- 28 4月, 2009 3 次提交
-
-
由 Heiko Schocher 提交于
because legacy NAND support is deprecated converting to current NAND interface. !This just compile, because I have no more the hardware to test it. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Detlev Zundel 提交于
As the common code also handles baudrate switching, which the board specific vct.c driver did not support, this is one of the rare occassions where deleting code actually adds a feature :) Signed-off-by: NDetlev Zundel <dzu@denx.de> Acked-by: NStefan Roese <sr@denx.de> Acked-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
-
由 Peter Tyser 提交于
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
-
- 27 4月, 2009 1 次提交
-
-
由 Dirk Behme 提交于
In recent U-Boot mmcinit changed to mmc init. Signed-off-by: NSteve Sakoman <steve@sakoman.com> Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
- 25 4月, 2009 1 次提交
-
-
由 David Brownell 提交于
Minor cleanup to clock-related defines for DaVinci DM6446 boards: - CONFIG_SYS_CLK_FREQ is unused; remove it. - CONFIG_SYS_NS16550_CLK must be the same as CONFIG_SYS_HZ_CLOCK On DM6446 both of those peripheral clocks actually come from the same source, the primary oscillator. Having them use the same symbol avoids bugs in the clone'n'modify development cycle. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
-
- 24 4月, 2009 1 次提交
-
-
由 Anatolij Gustschin 提交于
The size of U-Boot binary for MPC8360ERDK increased (> 2 flash sectors now), so 'saveenv' will partially overwrite U-Boot in flash and will brick the board. This patch moves environment offset to fourth flash sector and also fixes CONFIG_SYS_MONITOR_LEN. Signed-off-by: NAnatolij Gustschin <agust@denx.de> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
- 17 4月, 2009 4 次提交
-
-
由 David Brownell 提交于
Update the DaVinci DM6446 boards to use the new convention for CONFIG_SYS_NS16550_REG_SIZE ... the size hasn't changed from the original 4 bytes, but these chips are little-endian. (Resolves a regression added recently by the include/ns16550.h patch to "Unify structure declaration for registers". The code previously worked just fine because the registers were accessed as host-endian words, not as bytes.) Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
-
The timer has been rewrote with a precision at ~0,18% Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Tested-by: NSergey Lapin <slapin@ossfans.org> Tested-by: NEric BENARD <ebenard@free.fr>
-
由 Ilko Iliev 提交于
The PM9263 board is based on the AT91SAM9263-EK board. Here is the page on Ronetix website: http://www.ronetix.at/starter_kit_9263.htmlSigned-off-by: NIlko Iliev <iliev@ronetix.at> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
calculate dynamically the clock rate and pllb setting for usb Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 16 4月, 2009 2 次提交
-
-
由 Stefan Roese 提交于
Don't run the memory POST on the NAND-booting version. It will overwrite part of the U-Boot image which is already loaded from NAND to SDRAM. We were just lucky that it booted at all with this SDRAM test enabled. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Don't run the memory POST on the NAND-booting version. It will overwrite part of the U-Boot image which is already loaded from NAND to SDRAM. We were just lucky that it booted at all with this SDRAM test enabled. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 05 4月, 2009 8 次提交
-
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
unify arm cache management except for non standard cache as ARM7TDMI Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
由 Tom Rix 提交于
Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
由 Wolfgang Denk 提交于
-
由 Scott Wood 提交于
This brings it in line with other Freescale boards. Signed-off-by: NScott Wood <scottwood@freescale.com>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NStelian Pop <stelian@popies.net>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-