- 11 7月, 2017 10 次提交
-
-
由 Wadim Egorov 提交于
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC. The module can be connected to different carrier boards. It can be also equipped with different RAM, SPI flash and eMMC variants. The Rapid Development Kit option is using the following setup: - 1 GB DDR3 RAM (2 Banks) - 1x 4 KB EEPROM - DP83867 Gigabit Ethernet PHY - 16 MB SPI Flash - 4 GB eMMC Flash Add basic support for the PCM-947 carrier board, a RK3288 based development board made by PHYTEC. This board works in a combination with the phyCORE-RK3288 System on Module. Signed-off-by: NWadim Egorov <w.egorov@phytec.de> Reviewed-by: NSimon Glass <sjg@chromium.org> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Meng Dongyang 提交于
The driver changes gpio to fixed regulator to control vbus, so add fixed regulator node in DTS for xhci driver. Signed-off-by: NMeng Dongyang <daniel.meng@rock-chips.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Philipp Tomsich 提交于
This change migrates the USB_DWC2 configuration item to Kconfig and runs moveconfig to adjust header files and defconfig. Signed-off-by: NMeng Dongyang <daniel.meng@rock-chips.com> Split off into a separate patch: Ran moveconfig to migrate other boards: Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Kever Yang 提交于
rk3036 sdram driver does not use DM, remove CONFIG_RAM first. Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Kever Yang 提交于
Enable mmc_dw_rockchip driver, disable CONFIG_SPL_OF_PLATDATA first for some dependence patches still not merged. Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Tested-by: NVagrant Cascadian <vagrant@debian.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Kever Yang 提交于
evb_rk3229 is a RK3229 based board, with: - 8GB eMMC; - 1GB DDR SDRAM; - 2 USB2.0 HOST port; - 1 MAC port; - 1 HDMI port; - IR; - WiFi; Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Kever Yang 提交于
The rv1108 do not have DRAM driver now, so disable it first, or else it will get conflict with the sdram common code. Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Jorge Ramirez-Ortiz 提交于
This port adds support for: 1) Serial 2) eMMC 3) USB It has been tested with ARM TRUSTED FIRMWARE running u-boot as the BL33 executable [see board's README] eMMC has been tested for reading and booting the loader and linux kernels as well as saving the u-boot environment. USB has been tested with ASIX networking adapter and SanDisk 7.4GB drive. PSCI has been tested via the reset call (PSCI executes from DDR) The firwmare upgrade process has been tested via TFTP and USB FAT filesystem containing the fastboot.bin image in one of the partitions. Signed-off-by: NJorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
-
由 Cooper Jr., Franklin 提交于
Include K2G ICE to OF_LIST so it can be used for runtime board detection. Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Cooper Jr., Franklin 提交于
Enable various config options to allow U-boot at runtime to select the proper dtb to use from the list of dtb's within the FIT image. Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
- 10 7月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 09 7月, 2017 1 次提交
-
-
由 Christophe Leroy 提交于
CS Systemes d'Information (CSSI) manufactures two boards, named MCR3000 and CMPC885 which are respectively based on MPC866 and MPC885 processors. This patch adds support for the first board. Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
-
- 07 7月, 2017 9 次提交
-
-
由 Enric Balletbo i Serra 提交于
On startup the SL50 board halt at U-Boot prompt. Use CONFIG_AUTOBOOT_KEYED to enable autoboot for this board and define the <SPACE> key to get the U-Boot prompt. Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
-
由 Andy Shevchenko 提交于
AVR32 is gone. It's already more than two years for no support in Buildroot, even longer there is no support in GCC (last version is heavily patched 4.2.4). Linux kernel v4.12 got rid of it (and v4.11 didn't build successfully). There is no good point to keep this support in U-Boot either. Reviewed-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com> Reviewed-by: NHeiko Schocher <hs@denx.de> Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
-
由 xypron.glpk@gmx.de 提交于
The Odroid C2 comes with several expansion options such as an RTC module. As these expansions are not considered in the Linux device tree they have to be enabled via device tree overlays. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Peter Robinson 提交于
CHIP and CHIP Pro devices have options of DIP addon boards some of which need overlays from the beginning so it makes sense to enable device tree overlays. Signed-off-by: NPeter Robinson <pbrobinson@gmail.com>
-
由 Peter Robinson 提交于
96boards CE devices such as the DragonBoard and Hikey devices have numerous mezzanine options some of which need overlays from the beginning so it makes sense to enable device tree overlays. Signed-off-by: NPeter Robinson <pbrobinson@gmail.com>
-
由 Peter Robinson 提交于
TI am33xx devices such as the BeagleBone devices have numerous cape options such as screens some of which need overlays from the beginning so it makes sense to enable evice tree overlays. Signed-off-by: NPeter Robinson <pbrobinson@gmail.com>
-
由 Peter Robinson 提交于
Raspberry Pi has numerous HAT and other HW expansion options such as screens and cameras some of which need overlays from the beginning so it makes sense to enable evice tree overlays. Signed-off-by: NPeter Robinson <pbrobinson@gmail.com>
-
由 Ladislav Michl 提交于
Implement spl_start_uboot to let Falcon mode work. Signed-off-by: NLadislav Michl <ladis@linux-mips.org> Acked-by: NHeiko Schocher <hs@denx.de>
-
由 Ladislav Michl 提交于
Fastmap significantly reduces flash scan time, enable it by default. Signed-off-by: NLadislav Michl <ladis@linux-mips.org> Acked-by: NHeiko Schocher <hs@denx.de>
-
- 04 7月, 2017 1 次提交
-
-
由 Heiko Schocher 提交于
There was for long time no activity in the 4xx area. We need to go further and convert to Kconfig, but it turned out, nobody is interested anymore in 4xx, so remove it. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
- 30 6月, 2017 6 次提交
-
-
由 Marek Vasut 提交于
Use random ethaddr by default in case no ethaddr is set. Signed-off-by: NMarek Vasut <marex@denx.de>
-
由 Marek Vasut 提交于
Enable DFU and USB mass storage support for the DENX MA5D4 SoM. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com>
-
由 Alexey Brodkin 提交于
ARC HS Development Kit board is a new low-cost development platform sporting ARC HS38 in real silicon with nice set of features such as: * Quad-core ARC HS38 with 512 kB L2 cache and running @1GHz * 4Gb of DDR (we use only lowest 1Gb out of it now) * Lots of DesigWare peripherals * Different connectivity modules: - Synopsys HAPS HT3 - Arduino-compatible connector - MikroBUS This initial commit supports the following peripherals: * UART (DW 8250) * Ethernet (DW GMAC) * SD/MMC (DW Mobile Storage) * USB 1.1 & 2.0 Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
-
由 Alexey Brodkin 提交于
With eb5ba3ae "i2c: Drop use of CONFIG_I2C_HARD" in place we cannot use I2C EEPROM any longer so we're dropping all references to both EEPROM and I2C which was only used for EEPROM. Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com> Cc: Simon Glass <sjg@chromium.org>
-
由 Alexey Brodkin 提交于
Those could be easily used on USB flash drives or on SD/MMC cards. Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
-
由 Alexey Brodkin 提交于
There's no reason to keep data cache disabled in axs101 board any longer, enabling it. Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
-
- 29 6月, 2017 3 次提交
-
-
由 Heiko Schocher 提交于
since commit: f8b7fff1 "serial: atmel_usart: Add clk support" taurus board comes not up anymore. Fix it. Signed-off-by: NHeiko Schocher <hs@denx.de> Acked-by: NWenyou Yang <wenyou.yang@microchip.com>
-
由 Heiko Schocher 提交于
since commit: f8b7fff1 "serial: atmel_usart: Add clk support" smartweb board comes not up anymore. Fix it. Signed-off-by: NHeiko Schocher <hs@denx.de> Acked-by: NWenyou Yang <wenyou.yang@microchip.com>
-
由 Peter Robinson 提交于
The CONFIG_DEFAULT_FDT_FILE expects just the file not a full path as that might vary depending on the variant of Linux distro you might be using. Cc: Martin Donnelly <martin.donnelly@ge.com> Cc: Fabio Estevam <festevam@gmail.com> Signed-off-by: NPeter Robinson <pbrobinson@gmail.com> Acked-by: NFabio Estevam <fabio.estevam@nxp.com>
-
- 28 6月, 2017 1 次提交
-
-
由 Tom Rini 提交于
The ti816x SoC revision of the ethernet IP block is handled by the "davinci_emac" driver, rather than the "cpsw" driver as done by later members of the family. Enable the relevant plumbing. Signed-off-by: NSriramakrishnan <srk@ti.com> Signed-off-by: NVitaly Wool <vitaly.wool@konsulko.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 23 6月, 2017 1 次提交
-
-
由 Heiko Schocher 提交于
since commit: f8b7fff1 "serial: atmel_usart: Add clk support" corvus board comes not up anymore. Fix it. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
- 21 6月, 2017 1 次提交
-
-
由 Marek Vasut 提交于
The commit "fb82fe38 configs: Resync defconfigs" resynced all config files. This exposed two latent issues with the Gen3 boards in that we had not been setting CONFIG_DEFAULT_FDT_FILE correctly and had not been setting CONFIG_CMD_MMC. Fix both of these. Fixes: fb82fe38 ("configs: Resync defconfigs") Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 20 6月, 2017 2 次提交
-
-
由 Mike Looijmans 提交于
The topic-miamilite SoM contains a Zynq xc7z010 SoC, 1GB DDR3L RAM, 64MB dual-parallel QSPI NOR flash and clock sources. Signed-off-by: NMike Looijmans <mike.looijmans@topic.nl> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Mike Looijmans 提交于
Move the only use of CONFIG_SF_DUAL_FLASH to defconfig. This makes the associated topic_miamiplus.h header obsolete, so remove that as well. Signed-off-by: NMike Looijmans <mike.looijmans@topic.nl> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 19 6月, 2017 2 次提交
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Jaehoon Chung 提交于
Remove the CONFIG_DM_I2C_COMPAT config. Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
- 16 6月, 2017 2 次提交
-
-
由 Heiko Schocher 提交于
There was for long time no activity in the mpx5xxx area. We need to go further and convert to Kconfig, but it turned out, nobody is interested anymore in mpc5xxx, so remove it. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Michael Welling 提交于
Adds CONFIG_SPL_USB_GADGET_SUPPORT and CONFIG_SPL_USBETH_SUPPORT. Removes CONFIG_SPL_NAND_SUPPORT, CONFIG_SPL_MTD_SUPPORT, and CONFIG_SPL_YMODEM_SUPPORT to free up space to fit in RAM. Signed-off-by: NMichael Welling <mwelling@ieee.org> Reviewed-by: NTom Rini <trini@konsulko.com> Reviewed-by: NMarek Vasut <marex@denx.de>
-