- 18 9月, 2018 20 次提交
-
-
由 Mario Six 提交于
Add a driver to configure the SerDes (Serializer/Deserializer) lanes on the MPC83xx architecture. Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Add a CPU driver for the MPC83xx architecture. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Add a sandbox CPU driver, and some tests for the CPU uclass. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Add a method to probe all CPUs of the board. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Documentation in cpu.h is not in kernel-doc format. Change it to comply with it. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
When the DM CPU drivers are active, printing information about a CPU should be delegated to a matching driver. Hence, add a static print_cpuinfo that implements this delegation when DM CPU drivers are active. Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMario Six <mario.six@gdsys.cc> Changed condition to CONFIG_IS_ENABLED(CPU): Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Mario Six 提交于
The documentation in init.h is not in kernel-doc format. Fix this. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Includes should be sorted. Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Add a timer driver for the MPC83xx architecture. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Makefile entries should be sorted. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Add a clock driver for the MPC83xx architecture. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Add a sysreset driver for the MPC83xx platform. Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
To print the reset status during boot, add a method print_resetinfo to board_f, which is called in init_sequence_f[], that gets the reset information from the sysreset driver (assuming there is only one seems reasonable), and prints it. Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Add some tests for sysreset_get_status. Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
It's useful to have the reset status of the SoC printed out during reset (e.g. to learn whether the reset was caused by software or a watchdog). As a first step to implement this, add a get_status method to the sysreset class, which enables the caller to get printable information about the reset status (akin to get_desc in the CPU uclass). Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Define the read*_*/write*_* macros for the PowerPC platform to be able to use the macros in wait_bit.h. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Add a RAM driver for the MPC83xx architecture. Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Bin Meng 提交于
Imply CONFIG_BITREVERSE for Sandbox. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Andy Shevchenko 提交于
Sandbox is not a real bootloader and it does require a position independent code to be supported. Thus, build it with -fPIC explicitly. Fixes: 16940f720f9b ("Makefile: Don't generate position independent code") Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Reported-by: NSimon Glass <sjg@chromium.org> Tested-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org> Tested-by: NSimon Glass <sjg@chromium.org>
-
- 16 9月, 2018 7 次提交
-
-
-
-
-
-
由 Angelo Dureghello 提交于
This patch adds mcf5441x eSDHC support for the mcf5441x family. Signed-off-by: NAngelo Dureghello <angelo@sysam.it>
-
由 Angelo Dureghello 提交于
On a u32 val = __sw32(*addr); multiple memory accesses are not welcome, since "addr" may be an IO peripheral register address. This patch changes __sw16/32 to perform a single memory access for the source value. Signed-off-by: NAngelo Dureghello <angelo@sysam.it>
-
由 Angelo Dureghello 提交于
Signed-off-by: NAngelo Dureghello <angelo@sysam.it>
-
- 15 9月, 2018 13 次提交
-
-
由 Marek Vasut 提交于
The Gen2 TMU is fed with fixed 32.5 MHz signal from CP . This is then divided by 4 in TMU. Fix the timer clock setting in Gen2. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
-
由 Marek Vasut 提交于
Replace those two functions with generic ones by defining the timer macros in include/config/*.h . Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
-
由 Marek Vasut 提交于
The code uses all in all three TMU registers, drop the massive register layout structures and just define the required timer registers and use them throughout the code. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
-
由 Marek Vasut 提交于
The header contains only the TMU register layout, just inline it into the TMU timer implementation and drop the header completely. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
-
由 Marek Vasut 提交于
The R-Car Gen2 feeds the TMU with CONFIG_SYS_CLK_FREQ / 2, while the old SH parts use CONFIG_SYS_CLK_FREQ directly. Just put this into the TMU implementation and drop the CONFIG_SH_TMU_CLK_FREQ config option. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
-
由 Marek Vasut 提交于
This function just returns CONFIG_SH_TMU_CLK_FREQ, use the constant directly instead. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
-
由 Marek Vasut 提交于
These functions are always called for timer = 0, so drop the timer check. Since these functions are called from one place only and they are reduced to one line of code, just inline them. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
-
由 Marek Vasut 提交于
The tmu_bit value evaluates to (ffs(4) >> 1) - 1 = (3 >> 1) - 1 = 0. Just drop the tmu_bit completely as well as CONFIG_SYS_TMU_CLK_DIV. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
-
由 Marek Vasut 提交于
This constant is always 4 , for all boards that exist. Define it once in arch/sh/lib/time.c and remove it from the configs. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
-
由 Marek Vasut 提交于
Drop the macro as it is never used and it collides with sh_eth.h macros. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Marek Vasut 提交于
Drop the macro as it is defined in sh7723.h already. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Patrice Chotard 提交于
Add vbus-supply regulator support. On some board vbus is not controlled by the phy but by an external regulator. Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Dalon Westergreen 提交于
The dtb should be embedded in the u-boot-spl image so that the CONFIG_SPL_TARGET of spl/u-boot-spl.hex includes it. This also affects the main u-boot image, so adjust CONFIG_SPL_FS_LOAD_PAYLOAD_NAME to u-boot.img which now also includes the dtb. Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>
-