- 30 4月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 19 1月, 2019 1 次提交
-
-
由 Philipp Tomsich 提交于
The bounce buffer is used by a few drivers (most of the MMC drivers) to overcome limitations in their respective DMA implementation. This moves the configuration to Kconfig and makes it user-selectable (even though it will be a required feature to make those drivers work): the expected usage is for drivers depending on this to 'select' it unconditionally from their respective Kconfig (see follow-up patches). This commit includes a full migration using moveconfig.py to ensure that each commit compiles. To ensure bisectability we update dependencies of various drivers to now select BOUNCE_BUFFER when needed. [trini: Squash all patches to ensure bisectability] Signed-off-by: NTom Rini <trini@konsulko.com> Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion] Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion] Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
-
- 22 10月, 2018 1 次提交
-
-
由 Xiaoliang Yang 提交于
Move this option to Kconfig and tidy up the config file of eight boards which use it. Signed-off-by: NXiaoliang Yang <xiaoliang.yang_1@nxp.com>
-
- 17 8月, 2018 1 次提交
-
-
由 Tom Rini 提交于
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 09 4月, 2018 1 次提交
-
-
由 Mario Six 提交于
Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
- 28 2月, 2018 1 次提交
-
-
由 Michal Simek 提交于
Enable networking command only when NET is enabled. And remove selecting NET for CMD_NET Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 24 2月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 11 2月, 2018 1 次提交
-
-
由 Tom Rini 提交于
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 29 12月, 2017 1 次提交
-
-
由 Breno Lima 提交于
Currently the MX6SL option is selected via CONFIG_SYS_EXTRA_OPTIONS, but it is better to select it directly via Kconfig. Signed-off-by: NBreno Lima <breno.lima@nxp.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NPeng Fan <peng.fan@nxp.com>
-
- 11 10月, 2017 1 次提交
-
-
由 Tuomas Tynkkynen 提交于
Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
-
- 04 10月, 2017 1 次提交
-
-
由 Maxime Ripard 提交于
The g_dnl USB settings for the vendor ID, product ID and manufacturer are actually common settings that can and should be shared by all the gadgets. Make them common by renaming them, and convert all the users. Reviewed-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NLukasz Majewski <lukma@denx.de> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
- 28 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 15 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 26 7月, 2017 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 12 7月, 2017 1 次提交
-
-
由 Fabio Estevam 提交于
warp can run different kernel versions, such as NXP 4.1 or mainline. Currently the rootfs location is passed via mmcblk number and the problem with this approach is that the mmcblk number for the eMMC changes depending on the kernel version. In order to avoid such issue, use UUID method to specify the rootfs location. Succesfully tested booting a NXP 4.1 and also a mainline 4.12 kernel. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com> Acked-by: NOtavio Salvador <otavio@ossystems.com.br>
-
- 30 4月, 2017 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_BMODE Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: Make this default y and depend on mx5/6/7] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 26 1月, 2017 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_BOARD_EARLY_INIT_F Signed-off-by: NSimon Glass <sjg@chromium.org>
-
- 24 1月, 2017 1 次提交
-
-
由 Tom Rini 提交于
This option should not really be user selectable. Note that on PowerPC we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be conditional on that. Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
-
- 22 1月, 2017 1 次提交
-
-
由 Jagan Teki 提交于
Cc: Tom Rini <trini@konsulko.com> Signed-off-by: NJagan Teki <jagan@openedev.com>
-
- 27 9月, 2016 1 次提交
-
-
由 Tom Rini 提交于
Introduce a hidden USB_FUNCTION_DFU Kconfig option and select it for CMD_DFU (as we must have the DFU command enabled to do anything DFU). Make all of the entries in drivers/dfu/Kconfig depend on CMD_DFU and add options for all of the back end choices that DFU can make use of. Cc: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NLukasz Majewski <l.majewski@samsung.com>
-
- 10 9月, 2016 1 次提交
-
-
由 Tom Rini 提交于
In some cases we were missing CONFIG_USB=y so enable that when needed. Reviewed-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 07 9月, 2016 1 次提交
-
-
由 Fabio Estevam 提交于
Since commit a13d3757 ("warp: Use imx_ddr_size() for calculating the DDR size") warp board no longer boots. The reason for the breakage is that the warp board is using the DDR configuration from mx6slevk. A fundamental difference between warp and mx6slevk is that warp only uses one DDR chip select while mx6slevk uses two. The imx_ddr() function calculates the RAM size in runtime by reading the values of registers MDCTL and MDMISC. So in order to fix this warp boot issue, create a imximage DDR file specific to warp, where the MDCTL register is configured to only activates a single chip select. Reported-by: NBreno Lima <breno.lima@nxp.com> Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com> Tested-by: NBreno Lima <breno.lima@nxp.com>
-
- 17 6月, 2016 1 次提交
-
-
由 Tom Rini 提交于
With updated moveconfig.py and an better default, re-generate the migration of BOOTDELAY to the defconfig. Reviewed-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 26 4月, 2016 3 次提交
-
-
由 Tom Rini 提交于
Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 20 4月, 2016 3 次提交
-
-
由 Sam Protsenko 提交于
And also reformat defconfigs using "make savedefconfig" rule. Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>
-
由 Sam Protsenko 提交于
While at it, remove obsolete CONFIG_USBDOWNLOAD_GADGET option from some config headers. This is also probably fixes am335x_baltos board. Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>
-
由 Sam Protsenko 提交于
Move CONFIG_USB_GADGET_DUALSPEED option to Kconfig and make all UDC controllers select USB_GADGET_DUALSPEED: - add next options to Kconfig selecting USB_GADGET_DUALSPEED: - USB_GADGET_ATMEL_USBA - USB_GADGET_DWC2_OTG - USB_DWC3 - CI_UDC - make USB_MUSB_GADGET select USB_GADGET_DUALSPEED While at it, make some related fixes: - remove DUALSPEED from configs that don't enable gadget support: - kwb.h - tseries.h - add missing USB_GADGET option to next configs: - novena_defconfig - pcm051_rev*_defconfig - xfi3_defconfig Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>
-
- 26 3月, 2016 1 次提交
-
-
由 Sam Protsenko 提交于
The description was borrowed from kernel. "tristate" type was changed to "bool" (I believe we don't support modules for u-boot yet, right?). CONFIG_USB_GADGET requires CONFIG_USB to be defined too, so add it along as well. Definitions were added to defconfig files in a way that "make savedefconfig" generates exactly the same file as used defconfig. Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org> [trini: Add zynq_zc702 conversion] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 15 3月, 2016 1 次提交
-
-
由 Simon Glass 提交于
Move this option to Kconfig and tidy up existing boards. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
- 19 11月, 2015 1 次提交
-
-
由 Thomas Chou 提交于
Add CMD_GPIO to Kconfig and run tools/moveconfig.py . Signed-off-by: NThomas Chou <thomas@wytron.com.tw> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
- 02 9月, 2015 1 次提交
-
-
由 Peng Fan 提交于
Move TARGET_xx Kconfig option based on mx6 to arch/arm/cpu/armv7/mx6/Kconfig. Add enable "CONFIG_ARCH_MX6" for boards based on mx6. Then we can choose target boards using "make ARCH=arm menuconfig" with ARCH_MX6 defined. If using original way, we have no chance to enable ARCH_MX6 when "make menuconfig". Even define CONFIG_ARCH_MX6=y in xx_defconfig, kconfig will complains "arch/../configs/platinum_titanium_defconfig:3: warning: override: TARGET_PLATINUM_TITANIUM changes choice state" Signed-off-by: NPeng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Eric Bénard <eric@eukrea.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Marek Vasut <marex@denx.de> Cc: Christian Gmeiner <christian.gmeiner@gmail.com> Cc: Stefan Roese <sr@denx.de> Cc: Soeren Moch <smoch@web.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Acked-by: NStefano Babic <sbabic@denx.de> Acked-by: NSoeren Moch <smoch@web.de> Acked-by: NOtavio Salvador <otavio@ossystems.com.br> Acked-by: NChristian Gmeiner <christian.gmeiner@gmail.com>
-
- 26 6月, 2015 1 次提交
-
-
由 Joe Hershberger 提交于
This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 13 5月, 2015 1 次提交
-
-
由 Joe Hershberger 提交于
In order to reduce merge conflicts and to maintain the simplest possible defconfig files, we should be using the savedefconfig feature of Kconfig every time a new feature is added. This keeps the defconfig settings to a minimum (only those things not default) and keeps them in the same order as the Kconfig options. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: NStephen Warren <swarren@wwwdotorg.org> Cc: Tom Rini <trini@konsulko.com>
-
- 23 2月, 2015 1 次提交
-
-
由 Otavio Salvador 提交于
The WaRP Board is a Wearable Reference Plaform. The board features: - Freescale i.MX6 SoloLite processor with 512MB of RAM - Freescale FXOS8700CQ 6-axis Xtrinsic sensor - Freescale Kinetis KL16 MCU - Freescale Xtrinsic MMA955xL intelligent motion sensing platform The board implements a hybrid architecture to address the evolving needs of the wearables market. The platform consists of a main board and an example daughtercard with the ability to add additional daughtercards for different usage models. For more information about the project, visit: http://www.warpboard.org/Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br> Reviewed-by: NMarek Vasut <marex@denx.de> Acked-by: NStefano Babic <sbabic@denx.de>
-
- 30 7月, 2014 1 次提交
-
-
由 Masahiro Yamada 提交于
This commit adds: - arch/${ARCH}/Kconfig provide a menu to select target boards - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig set CONFIG macros to the appropriate values for each board - configs/${TARGET_BOARD}_defconfig default setting of each board (This commit was automatically generated by a conversion script based on boards.cfg) In Linux Kernel, defconfig files are located under arch/${ARCH}/configs/ directory. It works in Linux Kernel since ARCH is always given from the command line for cross compile. But in U-Boot, ARCH is not given from the command line. Which means we cannot know ARCH until the board configuration is done. That is why all the "*_defconfig" files should be gathered into a single directory ./configs/. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: NSimon Glass <sjg@chromium.org>
-