- 12 1月, 2006 2 次提交
-
-
由 Kumar Gala 提交于
Patch by Kumar Gala, 11 Jan 2006
-
由 Kumar Gala 提交于
Patch by Kumar Gala, 11 Jan 2006
-
- 29 12月, 2005 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 22 12月, 2005 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 19 12月, 2005 1 次提交
-
-
由 Wolfgang Denk 提交于
Patch by Eugen Bigz, 19 Dec 2005
-
- 17 12月, 2005 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 16 12月, 2005 1 次提交
-
-
由 Wolfgang Denk 提交于
The default of 255 is too short for slow devices. Patch by Martin Nykodym, 12 Dec 2005
-
- 15 12月, 2005 1 次提交
-
-
由 Stefan Roese 提交于
- Changed GPIO setup to enable another address line in order to address 64M of FLASH. - Added function sdram_tr1_set to auto calculate the tr1 value for the DDR. Patch by Steven Blakeslee, 12 Dec 2005
-
- 14 12月, 2005 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 12 12月, 2005 1 次提交
-
-
由 Wolfgang Denk 提交于
No commit message
-
- 07 12月, 2005 1 次提交
-
-
由 Marian Balakowicz 提交于
-
- 06 12月, 2005 1 次提交
-
-
由 Wolfgang Denk 提交于
Simplify TQM85xx Makefile handling.
-
- 04 12月, 2005 2 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
- 01 12月, 2005 5 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
With 64 kb uniform flash sector size the old value of 128 kB was too small.
-
由 Marian Balakowicz 提交于
ethaddr is assigned). Initialization moved from miiphy_register() to eth_initialize(). Based on initial patch for 4xx platform by Matthias Fuchs.
-
- 30 11月, 2005 4 次提交
-
-
由 Stefan Roese 提交于
- Support for TQM8541/8555 boards added. - Complete rework of TQM8540/8560 support. - Common TQM85xx code now supports all current TQM85xx platforms (TQM8540/8541/8555/8560). - DDR SDRAM size detection added. - CAS latency default values can be overwritten by setting "serial#" to e.g. "ABC0001 casl=25" -> CAS latency 2.5 will be used. If problems are detected with this non default CAS latency, the defualt values will be used instead. - FLASH size detection added. - Moved FCC ethernet driver initialization behind TSEC driver init -> TSEC is first device. Patch by Stefan Roese, 30 Nov 2005
-
由 Stefan Roese 提交于
Patch by Stefan Roese, 29 Nov 2005
-
由 Stefan Roese 提交于
Patch by John Otken, 23 Nov 2005
-
由 Stefan Roese 提交于
Patch by Stefan Roese, 27 Nov 2005
-
- 28 11月, 2005 2 次提交
-
-
由 Marian Balakowicz 提交于
-
由 Stefan Roese 提交于
On PPC44x platforms, the startup message generated in "cpu.c" only comprised the ppc type and revision but not additional informations like speed etc. Those speed infos where printed in the board specific code. This new implementation now prints all CPU infos in the common cpu specific code. No board specific code is needed anymore and therefore removed from all current 44x implementations. Patch by Stefan Roese, 27 Nov 2005
-
- 25 11月, 2005 2 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
The COPYING file was extended to make clear that these files can be used in non-GPL code, too.
-
- 22 11月, 2005 1 次提交
-
-
由 Stefan Roese 提交于
- Added onboard PPC440 DDR autodetection in cpu/ppc/sdram.c - CFG_FLASH_QUIET_TEST added to use the common CFI driver for bank autodetection Patch by Stefan Roese, 22 Nov 2005
-
- 21 11月, 2005 1 次提交
-
-
由 Wolfgang Denk 提交于
which makes the environment compatible with the hush shell. WARNING: Support for the old '$(...)' syntax will be discontinued in a later version.
-
- 17 11月, 2005 1 次提交
-
-
由 Rafal Jaworowski 提交于
-
- 15 11月, 2005 4 次提交
-
-
由 Stefan Roese 提交于
Patch by Stefan Roese, 15 Nov 2005
-
由 Stefan Roese 提交于
-
由 Stefan Roese 提交于
Patch by Stefan Roese, 15 Nov 2005
-
由 Stefan Roese 提交于
Added CONFIG_NET_MULTI for VOM405 board. Added reset_phy() for VOM405 board. Patch by Matthias Fuchs, 09 Nov 2005
-
- 11 11月, 2005 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 08 11月, 2005 1 次提交
-
-
由 Stefan Roese 提交于
Add support for error LED. Patch by Matthias Fuchs, 07 Nov 2005
-
- 07 11月, 2005 2 次提交
-
-
由 Stefan Roese 提交于
Patch by Stefan Roese, 07 Nov 2005
-
由 Stefan Roese 提交于
Patch by Stefan Roese, 07 Nov 2005
-
- 05 11月, 2005 1 次提交
-
-
由 Stefan Roese 提交于
Patch by Stefan Roese, 05 Nov 2005
-
- 03 11月, 2005 1 次提交
-
-
由 Wolfgang Denk 提交于
-