DDR RCW varies at different speeds. It is common for all platform. Move it
out from corenet_ds.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Extend CAS write Latency (CWL) table to comply with DDR3 spec
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The MPC8536 seems to use only 3 bits for the major revision field in the
SVR rather than the 4 bits used by all other processors.  The most
significant bit is used as a mfg code on MPC8536.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Move extern of pci_of_setup() into corenet_ds.h
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for RGMII, SGMII and XAUI Ethernet on P2041RDB board.

The five dTSEC can be routed to two on-board RGMII phy, three on-board
SGMII phy or four SGMII phy on SGMII riser card according to different
serdes protocol configuration and board lane configuration. Also updated
the device tree to direct the Fmac MAC to the correct PHY.

Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The P1023 has two 1G ethernet controllers the first can run in
SGMII, RGMII, or RMII.  The second can only do SGMII & RGMII.

We need to setup a for SoC & board registers based on our various
configuration for ethernet to function properly on the board.

Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NLei Xu <B33228@freescale.com>
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: NShaohui Xie <b21989@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for RGMII, SGMII, and XAUI (10Gb) Ethernet on P3041DS &
P5020DS ("Hydra").

The lane_to_slot[] array is initialized dynamically, since board switches
can be used to control the muxing of SERDES lanes to slots.

The BRDCFG1 PIXIS register is used to route the MII bus to the appropriate
slot.  The SERDES configuration is queried to help determine the routing
between MACs and slot/phy combination.

If a XAUI card is inserted, muxing for that card is enabled and never
turned off.  The PHY address for the 10G XAUI card depends on the slot in
which it's inserted.  If it's in slot 1, the address is 4.  If it's in
slot 2, the address is 0.

Update the MDIO routing in the P3041DS and P5020DS device trees based on
the board-level muxing.  The SERDES configuration determines which
SGMII/XGMII boards are located in which slots, and so the MDIO bus needs
to be muxed correctly whenever talking to a PHY connected to any Fman MAC.
The Fman Ethernet nodes in the device tree also need to be routed to the
correct PHYs.

Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for RGMII, SGMII, and XAUI (10Gb) Ethernet on P4080DS.

The board supports add-on cards for SGMII and XAUI functionality.  Which
slots on the board these cards are in is a function of the SERDES option
selected and muxes on the board.

Additionally because of the high-configurablity which MDIO bus one is
connected to is "selected" via an FPGA register.  We create dummy MDIO
bus for the phy layer and hide the mux manipulation in this dummy layer.

Add fman fdt helper function in board common code it'll be used by several
freescale boards that do various muxing of the MDIO signals based on which
controller/interface one is trying to talk to.

Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The Frame Manager (FMan) on QorIQ SoCs with DPAA (datapath acceleration
architecture) is the ethernet contoller block.  Normally it is utilized
via Queue Manager (Qman) and Buffer Manager (Bman).  However for boot
usage the FMan supports a mode similar to QE or CPM ethernet collers
called Independent mode.

Additionally the FMan block supports multiple 1g and 10g interfaces as a
single entity in the system rather than each controller being managed
uniquely.  This means we have to initialize all of Fman regardless of
the number of interfaces we utilize.

Different SoCs support different combinations of the number of FMan as
well as the number of 1g & 10g interfaces support per Fman.

We add support for the following SoCs:
 * P1023 - 1 Fman, 2x1g
 * P4080 - 2 Fman, each Fman has 4x1g and 1x10g
 * P204x/P3041/P5020 - 1 Fman, 5x1g, 1x10g
Signed-off-by: NDave Liu <daveliu@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NDai Haruki <dai.haruki@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: NLei Xu <B33228@freescale.com>
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NShaohui Xie <b21989@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Remove unnecessary or dead code/includes.
Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Some SOCs have discontiguously-numbered cores, and so we can't determine the
valid core numbers via the FRR register any more.  We define
CPU_TYPE_ENTRY_MASK to specify a discontiguous core mask, and helper functions
to process the mask and enumerate over the set of valid cores.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

We shouldn't be setting execute permissions on TLB entries that will not
actually have any code run from them.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add a helper function that will return a phandle value for the given
node.  If the node doesn't have a phandle already one will be created.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Acked-by: NGerald Van Baren <vanbaren@cideas.com>

The old fdt_create_phandle didn't actually create a phandle it just
set one.  We'll introduce a new helper that actually does creation.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Acked-by: NGerald Van Baren <vanbaren@cideas.com>

Add ifdef protection around fman specific code related to device tree
clock setup.  If we dont have CONFIG_SYS_DPAA_FMAN defined we shouldn't
be executing this code.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Issue: Address masking doesn't work properly.
When sum of the base address, defined by BA, and memory bank size,
defined by AM, exceeds 4GB (0xffff_ffff) then AMASKn[AM] doesn't mask
CSPRn[BA] bits.

Impact:
This will impact booting when we are reprogramming CSPR0(BA) and
AMASK0(AMASK) while executing from NOR Flash.

Workaround:
Re-programming of CSPR(BA) and AMASK is done while not executing from NOR
Flash. The code which programs the BA and AMASK is executed from L2-SRAM.
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Issue:
Peripheral connected to IFC_CS3 may hamper booting from IFC.

Impact:
Boot from IFC may not be successful if IFC_CS3 is used.

Workaround:
If IFC_CS3 is used, gate IFC_CS3 while booting from NAND or NOR.
Also Software should select IFC_CS3 using PMUXCR[26:27] = 0x01.
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Issue:
The NOR-FCM does not support access to unaligned addresses for 16 bit port size

Impact:
When 16 bit port size is used, accesses not aligned to 16 bit address boundary
will result in incorrect data

Workaround:
The workaround is to switch to GPCM mode for NOR Flash access.
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

For an IFC Erratum (A-003399) we will need to access IFC registers in
cpu_init_early_f() so expand the TLB covering CCSR to 1M.

Since we need a TLB to cover 1M we move to using TLB1 array for all the
early mappings so we can cover various sizes beyond 4k.
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

And various defines to enable NAND support and NAND spl code for the
P1010RDB platform.
Signed-off-by: NDipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add NAND support (including spl) on IFC, such as is found on the p1010.

Note that using hardware ECC on IFC with small-page NAND (which is what
comes on the p1010rdb reference board) means there will be insufficient
OOB space for JFFS2, since IFC does not support 1-bit ECC.  UBI should
work, as it does not use OOB for anything but ECC.

When hardware ECC is not enabled in CSOR, software ECC is now used.
Signed-off-by: NDipen Dudhat <Dipen.Dudhat@freescale.com>
[scottwood@freescale.com: ECC rework and misc fixes]
Signed-off-by: NScott Wood <scottwood@freescale.com>

Boot methods supported: NOR Flash, SPI Flash and SDCARD
This patch adds the following basic interfaces:
DDR3, eTSEC, DUART, I2C, SD/MMC, USB, SATA, PCIe, NOR Flash, SPI Flash.

P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
Local Bus (IFC):
	32Mbyte 16bit NOR flash
	32Mbyte SLC NAND Flash
	64KB CPLD device(GPCM interface)
SPI Flash:
	128 Mbit SPI Flash memory
SD/MMC:
	connector to interface with the SD memory card
SATA:
	1 internal SATA connect to 2.5. 160G SATA2 HDD
	1 eSATA connector to rear panel
USB 2.0:
	x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
	x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC:
	eTSEC1: Connected to RGMII PHY VSC8641XKO
	eTSEC2: Connected to SGMII PHY VSC8221
	eTSEC3: Connected to SGMII PHY VSC8221
eCAN:
	Two DB-9 female connectors for Field bus interface
UART:
	supports two UARTs up to 115200 bps for console
TDM:
	2 FXS ports connected via an external SLIC to the TDM interface.
SLIC:
	SPI SLIC
I2C:
	Serial EEprom
	Real time clock
	256 Kbit M24256 I2C EEPROM
PCIe:
	PCIe and mPCIe connectors.
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NDipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: NBhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The following boards share a common design but with minor variations
between them:

P1020MSBG-PC
P1020RDB-PC
P1020UTM-PC
P1021RDB-PC
P1024RDB
P1025RDB
P2020RDB-PC

The P1020RDB-PC shares its roots in the existing P1020RDB board design,
however uses DDR3 instead of DDR2.
P2020RDB-PC differs from the P102x RDB-PC with 64-bit DDR and 100Mhz SYSCLK.

Key features on these boards include:
* DDR3
* NOR flash
* NAND flash (on RDB's only)
* SPI flash (on RDB's only)
* SDHC/MMC card slot
* VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB)
* PCIE slot and mini-PCIE slots

As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM
is used to store SPD data. In case of absent or corrupted SPD, falling back
to timing data embedded in the source code will be used. Raw timing data is
extracted from DDR chip datasheet. Different speeds of DDR are supported
with this approach. ODT option is forced to fit this set of boards, again
because they don't have regular DIMMs.

CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet
specification for writing timing.

VSC firmware Address is defined by default in config file for eTSEC1.

SD width is based off DIP switch. DIP switch is detected on the
board by reading i2c bus and setting the appropriate mux values.

Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC
have pins multiplexing. QE function needs to be disabled to access Nor Flash
and CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe"
in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to
enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below

'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD.
'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NZhao Chenhui <b26998@freescale.com>
Signed-off-by: NMatthew McClintock <msm@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: NTang Yuantian <b29983@freescale.com>
Signed-off-by: Nramneek.mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NMatthew McClintock <msm@freescale.com>
Signed-off-by: NXie Xiaobo <X.Xie@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: NAkhil Goyal <akhil.goyal@freescale.com>

Before main memory (DDR) is initialized, the on-chip L1 cache is used as a
memory area for the stack and the global data (gd_t) structure.  This is
called the initial RAM area, or initram.  The L1 cache is locked and the TLBs
point to a non-existent address (so that there's no chance it will overlap
main memory or any device).  The L1 cache is also configured not to write
out to memory or the L2 cache, so everything stays in the L1 cache.

One of the things we might do while running out of initram is relocate CCSR.
On reset, CCSR is typically located at some high 32-bit address, like
0xfe000000, and this may not be the best place for CCSR.  For example, on
36-bit systems, CCSR is relocated to 0xffe000000, near the top of 36-bit
memory space.

On some future Freescale SOCs, the L1 cache will be forced to write to the
backing store, so we can no longer have the TLBs point to non-existent address.
Instead, we will point the TLBs to an unused area in CCSR.  In order for this
technique to work, CCSR needs to be relocated before the initram memory is
enabled.

Unlike the original CCSR relocation code in cpu_init_early_f(), the TLBs
we create now for relocating CCSR are deleted after the relocation is finished.
cpu_init_early_f() will still need to create a TLB for CCSR (at the new
location) for normal U-Boot purposes.  This is done to keep the impact to
existing U-Boot code minimal and to better isolate the CCSR relocation code.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW
macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS.
This is necessary for the assembly-language code that relocates CCSR, since
the assembler does not understand 64-bit constants.

CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the
CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it
should not be defined in a board header file.  Similarly,
CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so
it should also not be defined in the board header file.

CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that
CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT,
and so CCSR will not be relocated.

Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot
builds (e.g. NAND) are required to relocate CCSR only during the last stage
(i.e. the "real" U-Boot).  All other stages should define
CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated.

README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add UTMI and ULPI PHY support for USB controller on qoriq series of
processors with internal UTMI PHY implemented, for example P1010/P1014
 - Use both getenv() and hwconfig to get USB phy type till getenv()
   is depricated
 - Introduce CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY to specify if soc
   has internal UTMI phy
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: NRemy Bohmer <linux@bohmer.net>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Since commit d388298a by
Stefano Babic this file is no longer needed so delete it.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Loïc Minier <loic.minier@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This reverts commit 041c5422.

The lines removed by this commit weren't redundant. The logic is (and
probably should be better commented):

Find the intersection of the advertised capabilities of both sides of
the link (lpa).
From that intersection, find the highest capability we can run at
(that will be the negotiated link).

Now imagine that the intersection (lpa) is (LPA_100HALF | LPA_10FULL).

The code will now set phydev->speed to 100, and phydev->duplex to 1,
but this link does not support 100FULL.

Kudos to Andy Fleming <afleming@gmail.com> for binging this to
attention and for the explanation.
Signed-off-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>

* 'master' of git://git.denx.de/u-boot-arm:
  ARM: remove broken "ixdp425" and "ixpdg425" boards

Signed-off-by: NAlbert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: NStefan Roese <sr@denx.de>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

* 'master' of git://git.denx.de/u-boot-arm:
  OMAP3: beagle: Fix build warning in beagle.c

This is a trivial fix in the documentation, which corrects
board_init_r() source reference.
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>

Fix build warning

beagle.c:532: warning: initialization from incompatible pointer type
Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Koen Kooi <koen@dominion.thruhere.net>
CC: Joel A Fernandes <agnel.joel@gmail.com>
Cc: Greg Turner <gregturner@ti.com>
CC: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: NJason Kridner <jkridner@beagleboard.org>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>

The MAC address stored in the inventory eeprom begins at offset 1.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>