The GPIO_INT_ACT_LOW_SET was incorrectly handling interrupt lines higher than 7.
This is due to the fact that there are two registers for total of 16 lines.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>

nand.c: In function ‘pdnb3_nand_read_buf’:
nand.c:107:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
nand.c: In function ‘pdnb3_nand_dev_ready’:
nand.c:124:18: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]

Remove the 4-byte-at-time read mode altogether, the most is bogus and will
likely cause unaligned accesses.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>

Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>

IxEthAcc.c: In function ‘ixEthAccInit’:
IxEthAcc.c:105:21: warning: comparison between ‘IxEthDBStatus’ and ‘enum <anonymous>’ [-Wenum-compare]
IxEthDBAPISupport.c: In function ‘ixEthDBPortAddressSet’:
IxEthDBAPISupport.c:633:18: warning: variable ‘ackPortAddressLock’ set but not used [-Wunused-but-set-variable]
IxQMgrDispatcher.c: In function ‘ixQMgrLLPShow’:
IxQMgrDispatcher.c:1194:18: warning: variable ‘q’ set but not used [-Wunused-but-set-variable]
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>

These symbols are no longer defined in Linux-ARM's mach-types files. Replace
these with CONFIG_MACH_TYPE instead.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>

Add -EB flag to LD to switch endianness of the linker. This should make armeb
targets buildable again. Also, make use of U-Boot's internal libgcc instead of
toolchain's one, this works around the use of libraries from GCC, which might be
little endian.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>

The LD command in examples/standalone/Makefile ignored platform specific
LDFLAGS setup. Pass these LDFLAGS to the command.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>

Cc: Chandan Nath <chandan.nath@ti.com>
Tested-by: NTom Rini <trini@ti.com>
Signed-off-by: NMatt Porter <mporter@ti.com>

Adds support for loading U-Boot from UART using YMODEM protocol.
If YMODEM support is enabled in SPL and the romcode indicates
that SPL loaded via UART then SPL will wait for start of a
YMODEM transfer via the console port.
Signed-off-by: NMatt Porter <mporter@ti.com>
Signed-off-by: NTom Rini <trini@ti.com>

This document describes the SPL process for OMAP3 (and related) boards
as well as a partial memory map and how to verify certain aspects
outside of running on the target.
Signed-off-by: NTom Rini <trini@ti.com>

Signed-off-by: NTom Rini <trini@ti.com>

Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NTom Rini <trini@ti.com>

Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NTom Rini <trini@ti.com>

Testing for -fstack-usage requires the creation of an output file, which
isn't possible with /dev/null.
Signed-off-by: NTom Rini <trini@ti.com>

The '-fstack-usage' option to gcc will generate .su files, ignore them.
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NTom Rini <trini@ti.com>

This patch fixes erroneous 32-bit access to registers
hw_clkctrl_frac0 and hw_clkctrl_frac1.
Signed-off-by: NRobert Delien <robert@delien.nl>
Acked-by: NMarek Vasut <marex@denx.de>
Tested-by: NMarek Vasut <marex@denx.de>

This patch introduces an 8-bit register, mx28_register_8, in order to
prepare for fixing erroneous 32-bit wide access of registers
hw_clkctrl_frac0 and hw_clkctrl_frac1.
Signed-off-by: NRobert Delien <robert@delien.nl>
Acked-by: NMarek Vasut <marex@denx.de>
Tested-by: NMarek Vasut <marex@denx.de>

This patch renames mx28_register to mx28_register_32 in order to
prepare for the introduction of an 8-bit register, mx28_register_8.
Signed-off-by: NRobert Delien <robert@delien.nl>
Acked-by: NMarek Vasut <marex@denx.de>
Tested-by: NMarek Vasut <marex@denx.de>

Reformat the data so it's easier to navigate through them.
Signed-off-by: NMarek Vasut <marex@denx.de>

This prototype version SoM is unused and not available to public.
Support this only for internal debugging purposes.
Signed-off-by: NMarek Vasut <marex@denx.de>

The LCD pins configuration was wrong in U-Boot, configure pins properly.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <jason.hui@linaro.org>
Signed-off-by: NWolfgang Grandegger <wg@denx.de>

Currently, only USB Host 1 is supported.

Cc: Remy Bohmer <linux@bohmer.net>
Signed-off-by: NWolfgang Grandegger <wg@denx.de>

The SD loader binary is now downloadable at

https://wiki.linaro.org/Boards/MX6QSabreLite

under a open-source 3-clause BSD license. Update the README
for this.

The discussion shows that it's hard to change the hardware
regarding the default SPI NOR boot of the SabreLite boards.
I.e. this will stay the default boot. Therefore remove the
'early version of' statement.
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <liu.h.jason@gmail.com>

This patch replaces the use of magice numbers for scratch register
addresses with earlier defined register definitions.
Signed-off-by: NRobert Delien <robert@delien.nl>

This patch adds register definitions for the registers of the DIGCTL
IP-block.
Signed-off-by: NRobert Delien <robert@delien.nl>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Configuring for zipitz2 board...
zipitz2.c: In function ‘board_mmc_init’:
zipitz2.c:85:2: warning: implicit declaration of function ‘pxa_mmc_register’ [-Wimplicit-function-declaration]
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

This link script seems old and incompatible with relocation and its
own sa1000 start.S file. It isn't used because the CPU's link script
was picked up in preference to this.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Acked-by: NKristoffer Ericson <kristoffer.ericson@gmail.com>

Say good bye to some ancient, very broken and unused code.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>

CONFIG_SYS_INIT_SP_ADDR points to RAM, but it's used before
DRAM controller init. Fix it by setting CONFIG_SYS_INIT_SP_ADDR
to SRAM
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>

* 'master' of git://git.denx.de/u-boot-cfi-flash:
  cfi: fix the incomplete erased status check in buffer write

* 'master' of git://git.denx.de/u-boot-nds32:
  nds32/n1213: correct vector table in start.S
  nds32: fix ptrace and interrupt register overflow

This reverts commit 295d3942.

It turns that this really doesn't work very nicely. Instead we should
have a pre-console panic function so that we know that further execution
is impossible and we don't need to worry about trampling on UARTs, etc.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NWolfgang Denk <wd@denx.de>

Without the fix, flash_write_cfibuffer will terminate the erased
status check once an all-0xFF word has been found instead of
continuing the erased status check utill the first non-0xFF word.
Signed-off-by: NTao Hou <hotforest@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: NStefan Roese <sr@denx.de>

Recent bootstage commits made the code grow, which caused linker
errors.  Adjust the linker script to fix that.
Signed-off-by: NWolfgang Denk <wd@denx.de>

Correct definition of vector table in start.S
Signed-off-by: NMacpaul Lin <macpaul@gmail.com>

Fix ptrace and interrupt register overflow warning.
Add missing P0 and P1 (r26 and r27) into register lists.
These register are usually used in OS.
Signed-off-by: NMacpaul Lin <macpaul@gmail.com>

This patch adds FAT and ext2 command support for marvell gplugD
Signed-off-by: NAjay Bhargav <ajay.bhargav@einfochips.com>