An entry in the main Makefile for the mx31pdk board is not
necessary, and the board is added to boards.cfg as all
other targets.
Signed-off-by: NStefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>

Signed-off-by: NStefano Babic <sbabic@denx.de>

An entry in the main Makefile for the tx25 board is not
necessary, and the board is added to boards.cfg as all
other targets.
Signed-off-by: NStefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>

Unified DDR driver is maintained for better performance, robustness and bug
fixes. Upgrading to use unified DDR driver for MPC83xx takes advantage of
overall improvement. It requires changes for board files to customize
platform-dependent parameters.

To utilize the unified DDR driver, a board needs to define CONFIG_FSL_DDRx
in the header file. No more boards will be accepted without such definition.

Note: the workaround for erratum DDR6 for the very old MPC834x Rev 1.0/1.1
and MPC8360 Rev 1.1/1.2 parts is not migrated to unified driver.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The Frame Manager (FMan) on QorIQ SoCs with DPAA (datapath acceleration
architecture) is the ethernet contoller block.  Normally it is utilized
via Queue Manager (Qman) and Buffer Manager (Bman).  However for boot
usage the FMan supports a mode similar to QE or CPM ethernet collers
called Independent mode.

Additionally the FMan block supports multiple 1g and 10g interfaces as a
single entity in the system rather than each controller being managed
uniquely.  This means we have to initialize all of Fman regardless of
the number of interfaces we utilize.

Different SoCs support different combinations of the number of FMan as
well as the number of 1g & 10g interfaces support per Fman.

We add support for the following SoCs:
 * P1023 - 1 Fman, 2x1g
 * P4080 - 2 Fman, each Fman has 4x1g and 1x10g
 * P204x/P3041/P5020 - 1 Fman, 5x1g, 1x10g
Signed-off-by: NDave Liu <daveliu@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NDai Haruki <dai.haruki@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: NLei Xu <B33228@freescale.com>
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NShaohui Xie <b21989@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>

commit 0edf8b5b breaks
building on a different directory with the O= parameter.
The patch wil fix this issue, generating always asm-offsets.h before
the other targets.
Signed-off-by: NStefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Wolfgang Denk <wd@denx.de>

Some typoes in Makefile and boards.cfg make the M54455 board
and M53017 board configuration broken.
Signed-off-by: NJason Jin <Jason.jin@freescale.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Remove edb9301, edb9302, edb9302a, edb9307, edb9307a, edb9312,
edb9315 and edb9315a boards.
Signed-off-by: NWolfgang Denk <wd@denx.de>

This deletes the integrator split_by_variant.sh script and
defines a number of unique board types for the core modules
that are meaningful to support for the Integrator AP/CP, i.e.
the ones that did not just say "unsupported core module" in
split_by_variant.sh. If more core modules need to be supported
they are easy to add.

We delete all the old cruft in Makefile and MAKEALL that was
working around the old way of building boards. We create a
unique config file per board to satisfy the build system, but
they are just oneliners that include the existing
integratorap.h and integratorcp.h configs.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Based on earlier work by Alex Waterman <awaterman@dawning.com>.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>

Signed-off-by: NAsen Chavdarov Dimov <dimov@ronetix.at>
Signed-off-by: NReinhard Meyer <u-boot@emk-elektronik.de>

changed at91_serial_hw_init to at91_seriald_hw_init

Cc: Albin Tonnerre <tonnerrealbin@gmail.com>
CC: Gregory Hermant <gregory.hermant@calao-systems.com>
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>

Cc: Albin Tonnerre <tonnerrealbin@gmail.com>
Cc: Gregory Hermant <gregory.hermant@calao-systems.com>
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NReinhard Meyer <u-boot@emk-elektronik.de>

Removed SBC35 from MAKEALL

Versatile board is used as example to run u-boot under qemu.
The patch fixes relocation for all versatile boards and adds
a versatileqemu target to be used under qemu.

Patch tested only under qemu, not on real boards.
Tested with QEMU emulator version 0.14.50.
Signed-off-by: NStefano Babic <sbabic@denx.de>
CC: Alessandro Rubini  <rubini-list@gnudd.com>
CC: Loïc Minier <loic.minier@linaro.org>

Rework for AT91SAM9263-EK, makes it build again.
Based on the work for AT91SAM9260-EK.
Signed-off-by: NHong Xu <hong.xu@atmel.com>
Signed-off-by: NReinhard Meyer <uboot@emk-elektronik.de>

Fix board part of AT91SAM9261-EK according to the new scheme
Signed-off-by: NHong Xu <hong.xu@atmel.com>
Signed-off-by: NReinhard Meyer <u-boot@emk-elektronik.de>

Rework for AT91SAM9RL-EK, makes it build again.
Based on the work for AT91SAM9260-EK.
V4: added changes to MAKEALL
Signed-off-by: NHong Xu <hong.xu@atmel.com>
Signed-off-by: NReinhard Meyer <u-boot@emk-elektronik.de>

Provide appropriate '-O u-boot' while doing mkimage
for u-boot.img
Signed-off-by: NAneesh V <aneesh@ti.com>

creating an u-boot.ubl file, which contains the UBL Header
needed for booting from NAND with the RBL from TI. For more
information read doc/README.ublimage.
Signed-off-by: NHeiko Schocher <hs@denx.de>

Tell 'find' to follow symbolic links, so that files under include/asm
and arch/$(ARCH)/include/asm/arch are added to the indexing file list.
Signed-off-by: NHorst Kronstorfer <hkronsto@frequentis.com>
Acked-by: NDetlev Zundel <dzu@denx.de>

Now that the tools target requires the generated version header file, we
need to make sure that the directory it writes to exists.  In a configured
tree, this is taken care of for us.  But in an unconfigured one, the dir
does not yet exist causing a build error like so:

/bin/sh: line 5: ..../u-boot_build/include/version_autogenerated.h.tmp: No such file or directory

So create the dir for this file before we attempt to generate it.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The targets/prerequisites are the same here; the rules only differ in
the recipes.  So move the if logic protection to the recipe part so we
can keep the rest the same.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NAneesh V <aneesh@ti.com>
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@googlemail.com>

Signed-off-by: NAneesh V <aneesh@ti.com>
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@googlemail.com>

Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@googlemail.com>

This creates a standalone ELF that executes just the Blackfin initcode.
This is useful for people who want to program the low level aspects of
the CPU (memory/clocks/etc...) and can easily be used with JTAG for
quick booting while developing.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

On MPC85xx based NAND_SPL builds we generate a u-boot-nand_spl.lds based
on output from preprocessor.  We where never removed it.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NScott Wood <scottwood@freescale.com>

I can't build test this, but just looking at the config files written
and it seems OK ...
Tested-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NScott McNutt <smcnutt@psyent.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Looks like this was missed during the conversion to partial linking.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

mkimage relies on autogenerated version so we need to move
$(VERSION_FILE) rule out of ifeq and make tools rule depend on it to be
able to run 'make tools' from the unconfigured tree.
Signed-off-by: NIlya Yanok <yanok@emcraft.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>

LDSCRIPT is used only from the top-level Makefile and only when the
system is configured so we can move LDSCRIPT and CONFIG_SYS_LDSCRIPT
related logic into the top level Makefile and under configured condition
to avoid errors when building tools from unconfigured tree.
Signed-off-by: NIlya Yanok <yanok@emcraft.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>

The 'trab' board configuration is broken, and there is nobody who is
interested and willing to fix it.  Drop it.

This includes support for VFD displays which have always been used by
this board only.
Signed-off-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NEric Bénard <eric@eukrea.com>

Make ATMEL's at91sam9260/9g20/9xe-ek boards build again
Signed-off-by: NReinhard Meyer <u-boot@emk-elektronik.de>