- 28 10月, 2011 40 次提交
-
-
由 Tom Rini 提交于
We add an weak version of omap_rev_string in omap-common/spl.c and while at it drop the omap3 version. Move the prototype over to <asm/omap_common.h> with the other SPL functions. Signed-off-by: NTom Rini <trini@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Steve Sakoman 提交于
Signed-off-by: NSteve Sakoman <steve@sakoman.com> Acked-by: NKoen Kooi <k-kooi@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Steve Sakoman 提交于
The level shifters used on the Caspa camera module have a 4k output impedance. Combined with the 100uA pull-up resistors in the OMAP3, this raises the ground level to 400mV. Adding crosstalk between the pixel clock and the HS/VS signals on the flat cable (a ground line in between would have been nice), logic 0 levels can raise up to 650mV. This exceeds the camera input pins VIL maximum voltage. This change suggested-by Laurent Pinchart Signed-off-by: NSteve Sakoman <steve@sakoman.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Steve Sakoman 提交于
This pad was previously configured for sysclkout_1. This patch changes the configuration to gpio_10 to reduce radiated noise from the 26Mhz clock, as well as make the pin more generally useful. Signed-off-by: NSteve Sakoman <steve@sakoman.com> Acked-by: NPhilip Balister <philip@opensdr.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Simon Schwarz 提交于
Adding a DMA library to the SPL. It is used if CONFIG_SPL_DMA_SUPPORT is defined. Signed-off-by: NSimon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Simon Schwarz 提交于
Adds an interface to use the OMAP3 DMA. Signed-off-by: NSimon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Simon Schwarz 提交于
Adding the register definitions for omap3 DMA controller to cpu.h Signed-off-by: NSimon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Simon Schwarz 提交于
Adding the base register address of OMAP3 DMA controller. Signed-off-by: NSimon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 SRICHARAN R 提交于
All ddr configurations(geometry/timings) are done automatically by detecting the device connected at run time. Though this is a useful feature, making this as a default setting increases the code size by about 2K bytes. This is quite big, especially in the case of SPL which runs from a smaller SRAM. So do not use this feature as the default setting, instead use the precalculated tables. Signed-off-by: Nsricharan <r.sricharan@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sergei Shtylyov 提交于
MDSTAT.STATE occupies bits 0..5 according to all available documentation, so fix the mask which previously was leaving out the intermediate state indicator bit. While at it, introduce two #define's for that mask -- unfortunately, we can't use a single #define as the assembly code can't include <asm/arch/hardware.h> due to C-specfic constructs in it. Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
Not all padconfs are the same between 4430 and 4460, so instead of working around this with an if, we should have an specific padconf structure for both chips (like handling the differences between the LEDs GPIOs and TPS). Signed-off-by: NRicardo Salveti de Araujo <ricardo.salveti@linaro.org> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
Signed-off-by: NRicardo Salveti de Araujo <ricardo.salveti@linaro.org> 2 files changed, 17 insertions(+), 1 deletions(-) Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
OMAP4460 has a different set of values for the ID code, so moving the old ones to be related just with 4430. Signed-off-by: NRicardo Salveti de Araujo <ricardo.salveti@linaro.org> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Prafulla Wadaskar 提交于
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>
-
由 Michael Walle 提交于
The spi_init() function is missing. Add it. Signed-off-by: NMichael Walle <michael@walle.cc>
-
由 Lei Wen 提交于
Build pass with following config: dkb_config aspenite_config Signed-off-by: NLei Wen <leiwen@marvell.com>
-
由 Lei Wen 提交于
For files like the drivers/serial/serial.c, it must include the platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the definition in the platform definition files. Include the platform definition file in the config file, so that it would decouple the dependence for the driver files. Signed-off-by: NLei Wen <leiwen@marvell.com>
-
由 Lei Wen 提交于
Build pass with following config: dkb_config aspenite_config edminiv2_config openrd_ultimate_config sheevaplug_config mv88f6281gtw_ge_config rd6281a_config guruplug_config km_kirkwood_config Signed-off-by: NLei Wen <leiwen@marvell.com> Acked-by: NWolfgang Denk <wd@denx.de>
-
由 Lei Wen 提交于
For files like the drivers/serial/serial.c, it must include the platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the definition in the platform definition files. Include the platform definition file in the config file, so that it would decouple the dependence for the driver files. Signed-off-by: NLei Wen <leiwen@marvell.com>
-
由 Lei Wen 提交于
For files like the drivers/serial/serial.c, it must include the platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the definition in the platform definition files. Include the platform definition file in the config file, so that it would decouple the dependence for the driver files. Updated cpu.h to remove build errors for gplugd board (by prafulla) Signed-off-by: NLei Wen <leiwen@marvell.com> Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>
-
由 Lei Wen 提交于
For files like the drivers/serial/serial.c, it must include the platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the definition in the platform definition files. Include the platform definition file in the config file, so that it would decouple the dependence for the driver files. Signed-off-by: NLei Wen <leiwen@marvell.com>
-
由 Ajay Bhargav 提交于
This patch adds support for envrionment varaible storage in SPI flash for Marvell gplugD. Signed-off-by: NAjay Bhargav <ajay.bhargav@einfochips.com>
-
由 Ajay Bhargav 提交于
This patch enables Atmel AT45 SPI flash support for Marvell gplugD Enables SF commands. Signed-off-by: NAjay Bhargav <ajay.bhargav@einfochips.com>
-
由 Ajay Bhargav 提交于
This patch add SPI driver support for Marvell gplugD Signed-off-by: NAjay Bhargav <ajay.bhargav@einfochips.com>
-
由 Ajay Bhargav 提交于
This patch provides support for SPI emulated over SSP for Marvell Armada100 SOC. Signed-off-by: NAjay Bhargav <ajay.bhargav@einfochips.com>
-
由 Jason Cooper 提交于
Copied wholeheartedly from board/Marvell/guruplug and modified to add support for SPI NOR flash. CONFIG_MACH_DREAMPLUG defined in include/configs/dreamplug.h until Linus's kernel.org tree adds it to mach-types.h. Once it trickles down, the definition can be removed from include/configs/dreamplug.h. Signed-off-by: NJason Cooper <u-boot@lakedaemon.net>
-
由 Fabio Estevam 提交于
Fix checkpatch warning and errors in several i.MX related files. While at it also address a checkpatch warning at arch/arm/cpu/armv7/mx5/soc.c regarding the usage of extern in a C file. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Stefano Babic 提交于
Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Stefano Babic 提交于
Switch to new pmic generic driver. Signed-off-by: NStefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com>
-
由 Stefano Babic 提交于
Switch to new pmic generic driver. Signed-off-by: NStefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com>
-
由 Stefano Babic 提交于
Switch to new pmic generic driver. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Stefano Babic 提交于
Switch to new pmic generic driver. Signed-off-by: NStefano Babic <sbabic@denx.de> CC: Jason Liu <jason.hui@linaro.org> Acked-by: NJason Liu <jason.hui@linaro.org>
-
由 Stefano Babic 提交于
Switch to new pmic generic driver. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Stefano Babic 提交于
Switch to new pmic generic driver. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Stefano Babic 提交于
Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Stefano Babic 提交于
Instead of using directly the i2c_set_bus() function, the I2C_SET_BUS macro must be used to avoid build errors for targets without multibus I2C. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Stefano Babic 提交于
Switch to new pmic generic driver. Signed-off-by: NStefano Babic <sbabic@denx.de> CC: Marek Vasut <marek.vasut@gmail.com> Acked-by: NMarek Vasut <marek.vasut@gmail.com>
-
由 Stefano Babic 提交于
Switch to new pmic generic driver. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Stefano Babic 提交于
Signed-off-by: NStefano Babic <sbabic@denx.de>
-