- 23 11月, 2009 3 次提交
-
-
由 Marcel Ziswiler 提交于
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@noser.com> Tested-by: NHeiko Schocher <hs@denx.de>
-
由 Po-Yu Chuang 提交于
Signed-off-by: NPo-Yu Chuang <ratbert@faraday-tech.com> Edited commit message. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Mark Jackson 提交于
This patch adds a default bootargs "fbmem" value to the CONFIG_BOOTARGS string for the MIMC200 board. Signed-off-by: NMark Jackson <mpfj@mimc.co.uk>
-
- 17 11月, 2009 3 次提交
-
-
由 Matthias Fuchs 提交于
This patch fixes an ugly behavior of the IL712 magnetic coupler as used on VOM405. These parts will remember their last state over a power cycle which might cause unwanted behavior. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
This patch fixes an ugly behavior of the IL712 magnetic couplers as used on PLU405. These parts will remember their last state over a power cycle which might cause unwanted behavior. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
This patch is in preparation for the upcoming PLU405 board fix. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
- 16 11月, 2009 3 次提交
-
-
- 13 11月, 2009 3 次提交
-
-
由 Kumar Gala 提交于
We were incorrectly use the max CAM size as the number of entries in the array for setting up the addrmap. We should be using the NENTRY field which is the low 12-bits of TLB1CFG. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Mike Rapoport 提交于
Make smc911x_initialize return -1 on error and number of interfaces detected otherwise. Signed-off-by: NMike Rapoport <mike@compulab.co.il> Acked-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Mike Frysinger 提交于
When the smc911x driver was converted to NET_MULTI, the smc911x eeprom was missed. The config option needed updating as well as overhauling of the rergister read/write functions. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Tested-by: NMike Rapoport <mike.rapoport@gmail.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
- 12 11月, 2009 5 次提交
-
-
由 Dave Liu 提交于
commit 1542fbde introduced one new bug to chip-select interleaving. Single DDR controller also can do the chip-select interleaving if there is dual-rank or qual-rank DIMMs. Signed-off-by: NDave Liu <daveliu@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
-
-
由 javier Martin 提交于
Sometimes, inside NetLoop, eth_halt() is called before eth_init() has been called. This is harmless except for free() calls to pointers which have not been allocated yet. This patch initializes those pointers to NULL and allocates them only the first time. This way we can get rid of free calls in halt callback. This has been tested in i.MX27 Litekit board and eldk-4.2 toolchains. Signed-off-by: NJavier Martin <javier.martin@vista-silicon.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 javier Martin 提交于
This patch fixes erroneous access to the ethernet PHY which broke the driver. 1. Selector field in the auto-negotiation register must be 0x00001 for using 802.3, not 0x00000 which is reseved. 2. Access to the PHY address specified by CONFIG_FEC_MXC_PHYADDR, not 0x0 fixed address. This has been tested in i.MX27 Litekit board and eldk-4.2 toolchains. Now using proper defines for auto-negotiation register. Signed-off-by: NJavier Martin <javier.martin@vista-silicon.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
- 11 11月, 2009 1 次提交
-
-
由 Ron Lee 提交于
------------------------------------------------------------------------ GCC 4.4 complains about this now. Signed-off-by: NRon Lee <ron@debian.org>
-
- 10 11月, 2009 6 次提交
-
-
由 Ben Warren 提交于
Both lpd7a400 and lpd7a404 failed to compile because they had CONFIG_SMC_USE_IOFUNCS defined: examples/standalone/smc91111_eeprom.c:388: undefined reference to `SMC_outw' Also removed an orphaned paren in lpd7a404.h Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Ben Warren 提交于
This patch fixes the following warnings: Configuring for xaeniax board... smc91111_eeprom.c: In function 'print_macaddr': smc91111_eeprom.c:278: warning: suggest parentheses around + or - in operand of & smc91111_eeprom.c:281: warning: suggest parentheses around + or - in operand of & ... Configuring for xsengine board... smc91111_eeprom.c: In function 'print_macaddr': smc91111_eeprom.c:278: warning: suggest parentheses around + or - inside shift smc91111_eeprom.c:281: warning: suggest parentheses around + or - inside shift Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
-
由 Ben Warren 提交于
The following error was seen on impa7 board, due to its use of a 32-bit bus on CS8900. cs8900.c:137:37: error: macro "get_reg_init_bus" passed 2 arguments, but takes just 1 This patch gives the macro the correct number of arguments Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Mike Frysinger 提交于
The dev->halt() func can be called at any time, and the dev->recv() func does not need to use NetRxPackets[] when calling NetReceive(). Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Hui.Tang 提交于
Ensure all CS8900 data structures are assigned before accessing device Signed-off-by: NHui.Tang <zetalabs@gmail.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
- 09 11月, 2009 2 次提交
-
-
由 Stefan Roese 提交于
This error only appears when DEBUG is enabled in this driver. That's why it went unnoticed till now. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
This patch fixes a problem only seen very occasionally on Canyonlands. The NOR flash interface (CFI driver) doesn't work reliably in all cases. Erasing and/or programming sometimes doesn't work. Sometimes with an error message, like "flash not erased" when trying to program an area that should have just been erased. And sometimes without any error messages. As mentioned above, this problem was only seen rarely and with some PLL configuration (CPU speed, EBC speed). Now I spotted this problem a few times, when running my Canyonlands with the following setup (chip_config): 1000-nor - NOR CPU:1000 PLB: 200 OPB: 100 EBC: 100 Changing the EBC configuration to not release the bus into high impedance state inbetween the transfers (ATC, DTC and CTC bits set to 1 in EBC0_CFG) seems to fix this problem. I haven't seen any failure anymore with this patch applied. Signed-off-by: NStefan Roese <sr@denx.de> Cc: David Mitchell <dmitchell@amcc.com> Cc: Jeff Mann <MannJ@embeddedplanet.com>
-
- 08 11月, 2009 1 次提交
-
-
由 Remy Bohmer 提交于
The asm-arm/unaligned.h includes linux/unaligned/access_ok.h This file is unsafe to be used on ARM, since it does an unaligned memory accesses which fails on ARM. Lookin at Linux the basic difference seems to be the header "include/asm-arm/unaligned.h". The Linux version of "unaligned.h" does *not* include "access_ok.h" at all. It includes "le_byteshift.h" and "be_byteshift.h" instead. Signed-off-by: NRemy Bohmer <linux@bohmer.net> Signed-off-by: NStefan Roese <sr@denx.de> -- include/asm-arm/unaligned.h | 3 - include/linux/unaligned/be_byteshift.h | 70 +++++++++++++++++++++++++++++++++ include/linux/unaligned/le_byteshift.h | 70 +++++++++++++++++++++++++++++++++ 3 files changed, 142 insertions(+), 1 deletion(-) create mode 100644 include/linux/unaligned/be_byteshift.h create mode 100644 include/linux/unaligned/le_byteshift.h
-
- 05 11月, 2009 2 次提交
-
-
由 Kumar Gala 提交于
The nand_boot_fsl_elbc.c is shared between 83xx & 85xx however we should not be including the immap_83xx.h when building 85xx. We can just get this all from common.h Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Becky Bruce 提交于
The same code exists both inside an #ifdef and outside of it. Remove the extra code for all the 86xx boards. Signed-off-by: NBecky Bruce <beckyb@kernel.crashing.org> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 04 11月, 2009 2 次提交
-
-
由 Ed Swarthout 提交于
commit 70ed869e broke fsl pcie end-point initialization. Returning 0 is not correct. The function must return the first free bus number for the next controller. fsl_pci_init() must still be called and a bus allocated even if the controller is an end-point. Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com> Acked-by: NVivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
This reverts commit 70ed869e. There isn't any need to modify the API for fsl_pci_init_port to pass the status of host/agent(end-point) status. We can determine that internally to fsl_pci_init_port. Revert the patch that makes the API change. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 31 10月, 2009 2 次提交
-
-
由 Dave Liu 提交于
We need loop-check the flash clear lock and enable bit for L2 cache. Signed-off-by: NDave Liu <daveliu@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Wolfgang Denk 提交于
-
- 30 10月, 2009 4 次提交
-
-
由 Nobuhiro Iwamatsu 提交于
There was the point that did not use write macro. Change to write macro. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: NTakashi Yoshii <yoshii.takashi@gmail.com>
-
由 Nobuhiro Iwamatsu 提交于
By "arm/microblaze/nios/nios2/sh: Remove relocation fixups" (commit: 0630535e", doesn't need malloc_bin_reloc function. This commit remove this. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Ben Warren 提交于
Proper behavior is to pull MAC address from NVRAM in the initialization() an stuff it in dev->address, then program the device from dev->address in the init() function. Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
- 29 10月, 2009 3 次提交
-
-
由 Wolfgang Denk 提交于
The comment for the BR0_PRELIM port size initialization incorrectly stated 32 bit, while it's actually 16 bit. The code is correct. Reported-by: NGuenter Koellner <guenter.koellner@nsn.com> Signed-off-by: NWolfgang Denk <wd@denx.de>
-
-
-