- 04 1月, 2018 1 次提交
-
-
- 03 1月, 2018 5 次提交
-
-
由 Philipp Tomsich 提交于
The Rockchip-released ATF for the Firefly apparently (i.e. Kever reported this) does not tolerate a FDT being passed as the platform parameter and will run into a hard stop. To work around this limitation in the ATF parameter handling, we enable SPL_ATF_NO_PLATFORM_PARAM (which will force passing NULL for the platform parameters). Note that this only affects this platform, as the ATF releases for the RK3368 and RK3399 have always either ignored the platform parameter (i.e. before the FDT-based parameters were supported) or support receiving a pointer to a FDT. Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NKever Yang <kever.yang@rock-chips.com>
-
由 Philipp Tomsich 提交于
While we expect to call a pointer to a valid FDT (or NULL) as the platform parameter to an ATF, some ATF versions are not U-Boot aware and have an insufficiently robust (or an overzealour) parameter validation: either way, this may cause a hard-stop with uncooperative ATF versions. This change adds the option to suppress passing a platform parameter and will always pass NULL. Debug output from ATF w/ this option disabled (i.e. default): INFO: plat_param_from_bl2: 0x291450 Debug output from ATF w/ this option enabled: INFO: plat_param_from_bl2: 0 Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NKever Yang <kever.yang@rock-chips.com>
-
由 Peng Fan 提交于
The calculation of left space for version string is not correct, should use VIDEO_COLS not VIDEO_LINE_LEN / 2, otherwise we will get larger space than actual have and cause string to overlay logo picture. Also current version string display only supports two lines words at max. This also causes overlay when the LCD pixel column size is not enough. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Tested-by: NAnatolij Gustschin <agust@denx.de>
-
由 Peng Fan 提交于
The clk_set_rate function dereferences the clk pointer without checking whether it is NULL. This may cause problem when clk is NULL. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Philipp Tomsich 提交于
We want to have the same configuration defaults for the RK3368-uQ7 as for the RK3399-Q7: this change reduces the default env-size to 8KiB to ensure that it does not overlap the boot-payload on SD/MMC configurations. References: commit fe529e65 ("rockchip: rk3399-puma: reduce env size to 8kiB") Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
- 02 1月, 2018 2 次提交
-
-
由 Neil Armstrong 提交于
Khadas VIM is an Open Source DIY Box manufactured by Shenzhen Wesion NOT 'Tomato' The fix was provided by Khadas Team member 'numbqq'. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 01 1月, 2018 10 次提交
-
-
-
由 Felix Brack 提交于
The patch replaces the former error() by the new pr_err(). This makes the TPS65910 driver conform to Masahiro's patch 'treewide:replace with error() with pr_err()' introduced October 2017. Signed-off-by: NFelix Brack <fb@ltec.ch> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Sam Protsenko 提交于
Commit b6251db8 ("Kconfig: Introduce USE_BOOTCOMMAND and migrate BOOTCOMMAND") removed CONFIG_BOOTCOMMAND option from include/configs/am335x_evm.h file. But that option wasn't added to defconfig files for BeagleBone Black board. Because of this we can't boot Linux from SD card using just "run bootcmd", getting next error: ** File not found /boot/undefined ** That's because "fdtfile" variable has "undefined" value by default, and "bootcmd" doesn't call "run findfdt" command, which assigns "fdtfile" to correct device tree file for current board name (obtained from EEPROM). So we are forced to either call "run findfdt" command manually, or assign manually "fdtfile=am335x-boneblack.dtb" (e.g. in uEnv.txt file). Bring back CONFIG_BOOTCOMMAND to BBB defconfigs so that we can boot Linux rootfs from SD card automatically without any addition actions. Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>
-
由 Heinrich Schuchardt 提交于
struct driver_info has no field 'flags'. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Derald D. Woods 提交于
This commit clears 'ethaddr' before calling 'smc911x_initialize' to allow the SROM MAC address to be assigned properly. Signed-off-by: NDerald D. Woods <woods.technical@gmail.com>
-
由 Derald D. Woods 提交于
This commit updates the configuration files needed to support OF_CONTROL on the OMAP3 EVM baseboard. Additionally: - CONFIG_SYS_THUMB_BUILD is enabled - CONFIG_SPL_ENV_SUPPORT is enabled Tested using GCC 7.2.0 [--with-float=hard --with-mode=thumb]. Signed-off-by: NDerald D. Woods <woods.technical@gmail.com>
-
由 Derald D. Woods 提交于
This commit adds OMAP3 EVM devicetree files from Linux v4.15-rc3. Note that this is the first addition of OMAP34XX devicetree files. Signed-off-by: NDerald D. Woods <woods.technical@gmail.com>
-
由 Derald D. Woods 提交于
This commit keeps the 'fdtaddr' as provided by DEFAULT_LINUX_BOOT_ENV. Signed-off-by: NDerald D. Woods <woods.technical@gmail.com>
-
由 Kever Yang 提交于
Enable sdmmc node in SPL and add it to boot order. Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> [Fixed commit tags:] Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Jakob Unterwurzacher 提交于
This commit changes the size of the enviroment (for the RK3399-Q7) to 8kiB for all possible locations of the environment (i.e. even when the environment is saved to SD card). With the default of 32kiB, the environment overwrites the SPL stage which lives at 16kiB. Signed-off-by: NJakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> [Reworked commit-message:] Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
- 29 12月, 2017 20 次提交
-
-
-
由 Patrick Bruenn 提交于
Since commit 999a78d5 ("scripts/dtc: Update to upstream version v1.4.5-3-gb1a60033c110") dtc warns about: arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/serial@53fc0000 arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/ccm@53fd4000 arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/gpio@53fe4000 arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/sdma@63fb0000 arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/ethernet@63fec000 Fix this by adding a node for the tzic interrupt controller. Copied from "<Linux>/arch/arm/boot/dts/imx53.dts" Signed-off-by: NPatrick Bruenn <p.bruenn@beckhoff.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Marek Vasut 提交于
The DDR DRAM calibration doesn't work on T-topology sometimes, so disable it. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
由 Vagrant Cascadian 提交于
In commit 6e6cf015 ("Merge git://www.denx.de/git/u-boot-imx") the line defining spl_sd configuration for wandboard was removed, which resulted in no SPL target being built. Add it back. Signed-off-by: NVagrant Cascadian <vagrant@debian.org> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Breno Lima 提交于
Currently CONFIG_SECURE_BOOT is selecting FSL_CAAM for all i.MX devices, this causes the following error when building mx6sl boards since this SoC doesn't have the CAAM block: In file included from drivers/crypto/fsl/jobdesc.c:12:0: drivers/crypto/fsl/jobdesc.c: In function 'inline_cnstr_jobdesc_blob_dek': include/fsl_sec.h:268:25: error: 'CAAM_ARB_BASE_ADDR' undeclared (first use in this function) #define SEC_MEM_PAGE1 (CAAM_ARB_BASE_ADDR + 0x1000) ^ drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1' memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz); ^ include/fsl_sec.h:268:25: note: each undeclared identifier is reported only once for each function it appears in #define SEC_MEM_PAGE1 (CAAM_ARB_BASE_ADDR + 0x1000) ^ drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1' memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz); ^ scripts/Makefile.build:280: recipe for target 'drivers/crypto/fsl/jobdesc.o' failed make[3]: *** [drivers/crypto/fsl/jobdesc.o] Error 1 scripts/Makefile.build:425: recipe for target 'drivers/crypto/fsl' failed make[2]: *** [drivers/crypto/fsl] Error 2 scripts/Makefile.build:425: recipe for target 'drivers/crypto' failed make[1]: *** [drivers/crypto] Error 2 Add HAS_CAAM configuration to avoid this error. Signed-off-by: NBreno Lima <breno.lima@nxp.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Breno Lima 提交于
MX6UL contains features that MX6ULL doesn't support. Deselect CONFIG_MX6UL and select SYS_L2CACHE_OFF and ROM_UNIFIED_SECTIONS. The motivation for doing this change is that MX6UL supports CAAM and MX6ULL does not. Signed-off-by: NBreno Lima <breno.lima@nxp.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Breno Lima 提交于
Currently the MX6SL option is selected via CONFIG_SYS_EXTRA_OPTIONS, but it is better to select it directly via Kconfig. Signed-off-by: NBreno Lima <breno.lima@nxp.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NPeng Fan <peng.fan@nxp.com>
-
由 Breno Lima 提交于
Secure boot is not enabled in warp imximage.cfg, add support for it. Signed-off-by: NBreno Lima <breno.lima@nxp.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Breno Lima 提交于
Secure boot is not enabled in mx6slevk imximage.cfg, add support for it. Signed-off-by: NBreno Lima <breno.lima@nxp.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com> Acked-by: NPeng Fan <peng.fan@nxp.com>
-
由 Fabio Estevam 提交于
Currently only imx6sx-sdb.dtb is loaded, but if revA board is used the correct dtb is imx6sx-sdb-reva.dtb, so make this possible. While at it, remove an extra 'mmc dev'. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Fabio Estevam 提交于
NXP development boards based on i.MX6/i.MX7 contain the board revision information stored in the fuses. Introduce a common function that can be shared by different boards and convert mx6sabreauto to use this new mechanism. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Lukasz Majewski 提交于
This commit switch display5_factory_defconfig to use new, generic USE_BOOTCOMMAND Kconfig option. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Peng Fan 提交于
Include dm/ofnode.h. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Christopher Spinrath 提交于
Commit 5248930e ("dm: imx: cm_fx6: Enable more driver model support") enabled driver model support for MMC. Remove the old mmc init code, which is no longer used, from the board file. Signed-off-by: NChristopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Christopher Spinrath 提交于
Commit 5248930e ("dm: imx: cm_fx6: Enable more driver model support") enabled driver model support for AHCI. Remove the old, now unused, sata init code from the board file. Signed-off-by: NChristopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Christopher Spinrath 提交于
Commit 5248930e ("dm: imx: cm_fx6: Enable more driver model support") enabled driver model support for USB. But it missed to enable driver model support for keyboards. As a result, USB keyboards do no longer work. Fix this by enabling driver model support for keyboards. Fixes: 5248930e ("dm: imx: cm_fx6: Enable more driver model support") Signed-off-by: NChristopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Christopher Spinrath 提交于
Commit 5248930e ("dm: imx: cm_fx6: Enable more driver model support") enabled driver model support for USB, thereby effectively removing USB support because the cm_fx6 devicetree in the U-Boot does *not* enable the USB nodes. Reinstate the USB support by syncing the devicetree with Linux whose devicetree enables the USB nodes properly. More precisely, use the devicetree found in Linux v4.15-rc1 with the following two changes: 1) Remove the audio mux; the required dt-bindings header is not present in the U-Boot. 2) Keep the usdhc3 MMC controller node currently present in the U-Boot's devicetree to retain the ability to boot from MMC. Fixes: 5248930e ("dm: imx: cm_fx6: Enable more driver model support") Signed-off-by: NChristopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Martyn Welch 提交于
We are going to be using check_time() on more than the mx53ppd, move this function to a common location. Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk>
-
由 Adam Ford 提交于
There is an #ifdef and #endif with nothing in between. This patch simply removes this dead/useless code. Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Fabio Estevam 提交于
In order to provide a consistent user experience for imx board users, remove the custom CONFIG_BOOTDELAY values from defconfig files, so that all boards can use the default two second delay. Signed-off-by: NFabio Estevam <festevam@gmail.com> Reviewed-by: NLukasz Majewski <lukma@denx.de>
-
- 27 12月, 2017 2 次提交
-
-
-
由 Masahiro Yamada 提交于
Freescale (NXP) boards have lots of defconfig files per board. I used "imply PANIC_HANG" for them. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-