- 29 11月, 2011 1 次提交
-
-
由 Stelian Pop 提交于
Change my old email address which is no longer valid. Signed-off-by: NStelian Pop <stelian@popies.net> Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
- 17 7月, 2011 1 次提交
-
-
由 Albert ARIBAUD 提交于
Checkpatch.pl complains about the volatile qualifier in calls to get_ram_size(). Remove this qualifier in the prototype and in the calls where it is useless, and leave it only in the function body where it is needed. Signed-off-by: NAlbert ARIBAUD <albert.u.boot@aribaud.net>
-
- 22 6月, 2011 1 次提交
-
-
由 Eric Benard 提交于
Signed-off-by: NEric Bénard <eric@eukrea.com>
-
- 28 4月, 2011 1 次提交
-
-
由 Eric Benard 提交于
- update to new relocation code - switch to boards.cfg - get rid of LEGACY (still a little hack in .h to compile) - add nand boot configuration - boot tested for the following configurations : 9260 (64MB RAM & nor boot) 9260_nand (64MB RAM & nand boot) 9G20_128M (128MB RAM & nor boot) 9G20_nand_128M (128MB RAM & nand boot) (nor boot is using lowlevel init) Signed-off-by: NEric Bénard <eric@eukrea.com>
-
- 12 7月, 2010 1 次提交
-
-
由 Ben Warren 提交于
Also, remove all calls to eth_init() in boards that use MACB Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
- 19 10月, 2009 1 次提交
-
-
由 Eric Benard 提交于
Signed-off-by: NEric Benard <eric@eukrea.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
- 13 10月, 2009 1 次提交
-
-
由 Tom Rix 提交于
these boards are built around Atmel's AT91SAM9260/9G20 and have up to 64MB of NOR flash, up to 128MB of SDRAM, up to 2GB of NAND and include a 10/100 Ethernet PHY in RMII mode. Signed-off-by: NEric Benard <eric@eukrea.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
- 02 9月, 2009 1 次提交
-
-
由 Albin Tonnerre 提交于
Commit 7ebafb7e introduced a mistake in the spi init function call for those boards. This patch fixes this. Signed-off-by: NAlbin Tonnerre <albin.tonnerre@free-electrons.com>
-
- 07 7月, 2009 1 次提交
-
-
由 Sedji Gaouaou 提交于
On the boards at91sam9260ek, at91sam9263ek and afed9260, the rstc register was set to 0 after being set to 500 ms for the PHY reset. Do backup the old reset length and restore it after the MACB initialisation. Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com> Signed-off-by: NStelian Pop <stelian@popies.net>
-
- 22 3月, 2009 5 次提交
-
-
由 Nicolas Ferre 提交于
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed. The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board. It is essentially the same, with a few minor differences. Here is the chip page on Atmel website: http://www.atmel.com/dyn/products/product_card.asp?part_id=4337Signed-off-by: NJustin Waters <justin.waters@timesys.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 07 11月, 2008 2 次提交
-
-
由 Stelian Pop 提交于
AT91_BASE_EMAC is never used outside the board specific files, so replace its usage by the board specific AT91xxx_BASE_EMAC. Signed-off-by: NStelian Pop <stelian@popies.net> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
由 Stelian Pop 提交于
AT91_ID_US0 / AT91_ID_US1 / AT91_ID_US2 were used but never defined. Since they are never used outside the board specific files, they can be replaced by the board specific AT91xxx_ID_US0 / AT91xxx_ID_US1 / AT91xxx_ID_US2. Bug spotted by Jesus Alvarez <jalvarez@micromint.com>. Signed-off-by: NStelian Pop <stelian@popies.net> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 19 10月, 2008 1 次提交
-
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 03 9月, 2008 1 次提交
-
-
由 Ben Warren 提交于
Removed at91sam9_eth_initialize() from net/eth.c Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
- 13 7月, 2008 1 次提交
-
-
由 Anatolij Gustschin 提交于
On the at91sam9260ep development board there is an EEPROM connected to the TWI interface (PA23, PA24 Peripheral A multiplexing), so we cannot use these pins as ETX2, ETX3. This patch configures PA10, PA11 pins for ETX2, ETX3 instead of PA23, PA24 pins. Signed-off-by: NAnatolij Gustschin <agust@denx.de> Signed-off-by: NManuel Sahm <Manuel.Sahm@feig.de>
-
- 05 7月, 2008 2 次提交
-
-
由 Patrice Vilchez 提交于
Fix NAND FLASH timings for at91sam9x evaluation kits. New timings are based on application note "NAND Flash Support on AT91SAM9 Microcontrollers" available at http://atmel.com/dyn/resources/prod_documents/doc6255.pdfSigned-off-by: NPatrice Vilchez <patice.vilchez@atmel.com> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NStelian Pop <stelian@popies.net>
-
由 Stelian Pop 提交于
AT91 RSTC registers are battery-backuped, so their values are not reset across power cycles. One of those registers, the AT91_RSTC_MR register, is being modified by U-Boot, in the ethernet initialisation routine, to generate a 500ms user reset. Unfortunately, this value is not being restored afterwards, causing subsequent resets to also last for 500ms. This long reset sequence causes problems (at least) in the boot sequence from NOR: by the time the CPU tries to load a program from the NOR flash, the latter is still in reset and not yet available. Additionaly, this patch fixes a bug in the original code which caused the reset delay to last for 2s instead of 500ms. Signed-off-by: NStelian Pop <stelian@popies.net> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 21 5月, 2008 1 次提交
-
-
由 Wolfgang Denk 提交于
This commit gets rid of a huge amount of silly white-space issues. Especially, all sequences of SPACEs followed by TAB characters get removed (unless they appear in print statements). Also remove all embedded "vim:" and "vi:" statements which hide indentation problems. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 10 5月, 2008 4 次提交
-
-
由 Stelian Pop 提交于
The Atmel boards can handle 8 or 16 bit NAND memories. This patch makes the support configurable in the board config header file (CFG_NAND_DBW_8 or CFG_NAND_DBW_16). Signed-off-by: NStelian Pop <stelian@popies.net> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
由 Stelian Pop 提交于
When doing the AT91CAP9/AT91SAM9 port, a number of header files were copied from the Linux kernel sources. This patch explicitly specifies this origin for all the copied headers, and for those missing copyright information, adds it. Additionaly, the header file 'at91sam926x_mc.h' has been superceeded in the latest kernel sources by 'at91sam9_smc.h'. The copyright information has been confirmed by the AT91 Linux kernel maintainer, Andrew Victor <avictor.za@gmail.com>. Signed-off-by: NStelian Pop <stelian@popies.net> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
由 Stelian Pop 提交于
When applying the AT91CAP9 patches upstream, something transformed the '@' character into the ' <at> ' sequence. The patch below restores the original form in all the places where it has been modified (the AT91CAP9 files, the AT91SAM9260 files which were copied from AT91CAP9, and a couple of other files where the ' <at> ' sequence was present). Signed-off-by: NStelian Pop <stelian@popies.net>
-
由 Stelian Pop 提交于
When doing the AT91CAP9/AT91SAM9 port, a number of header files were copied from the Linux kernel sources. This patch explicitly specifies this origin for all the copied headers, and for those missing copyright information, adds it. Additionaly, the header file 'at91sam926x_mc.h' has been superceeded in the latest kernel sources by 'at91sam9_smc.h'. The copyright information has been confirmed by the AT91 Linux kernel maintainer, Andrew Victor <avictor.za@gmail.com>. Signed-off-by: NStelian Pop <stelian@popies.net>
-
- 09 5月, 2008 1 次提交
-
-
由 Stelian Pop 提交于
When applying the AT91CAP9 patches upstream, something transformed the '@' character into the ' <at> ' sequence. The patch below restores the original form in all the places where it has been modified (the AT91CAP9 files, the AT91SAM9260 files which were copied from AT91CAP9, and a couple of other files where the ' <at> ' sequence was present). Signed-off-by: NStelian Pop <stelian@popies.net> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 01 4月, 2008 1 次提交
-
-
由 Stelian Pop 提交于
Support for booting from internal DataFlash, external DataFlash card or NAND flash is available. Signed-off-by: NStelian Pop <stelian@popies.net>
-