- 18 8月, 2017 1 次提交
-
-
由 Angelo Dureghello 提交于
For certain boot types and sbf, for V4 cpu's, an early ddr/sdram init is required. This patch moves this ddr/sdram early initalization away from start.S (to be board related). Signed-off-by: NAngelo Dureghello <angelo@sysam.it>
-
- 17 8月, 2017 4 次提交
-
-
-
git://git.denx.de/u-boot-sunxi由 Tom Rini 提交于
Update A20-OLinuXino-Lime2-eMMC_defconfig to include CONFIG_SCSI Signed-off-by: NTom Rini <trini@konsulko.com>
-
git://www.denx.de/git/u-boot-imx由 Tom Rini 提交于
Update pfla02 for setenv changes and PHYLIB/etc migration to Kconfig. Signed-off-by: NTom Rini <trini@konsulko.com>
-
-
- 16 8月, 2017 35 次提交
-
-
由 Bin Meng 提交于
On some flash (like Macronix), QE (quad enable) bit is in the same status register as BP# bits, and we need preserve its original value during a reboot cycle as this is required by some platforms (like Intel ICH SPI controller working under descriptor mode). Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NJagan Teki <jagan@openedev.com> [Refined code for readability] Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Simon Glass 提交于
The load() methods have inconsistent behaviour on error. Some of them load an empty default environment. Some load an environment containing an error message. Others do nothing. As a step in the right direction, have the method return an error code. Then the caller could handle this itself in a consistent way. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
In principle this can fail, e.g. if the index is out of range. Adjust the driver signature to allow returning an error code. Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
We are now using an env_ prefix for environment functions. Rename these other functions as well, for consistency: getenv_vlan() getenv_bootm_size() getenv_bootm_low() getenv_bootm_mapsize() env_get_default() Suggested-by: NWolfgang Denk <wd@denx.de> Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Rename this function for consistency with env_get(). Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
We are now using an env_ prefix for environment functions. Rename these for consistency. Also add function comments in common.h. Suggested-by: NWolfgang Denk <wd@denx.de> Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
We are now using an env_ prefix for environment functions. Rename these two functions for consistency. Also add function comments in common.h. Quite a few places use getenv() in a condition context, provoking a warning from checkpatch. These are fixed up in this patch also. Suggested-by: NWolfgang Denk <wd@denx.de> Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Rename this function for consistency with env_set(). Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
We are now using an env_ prefix for environment functions. Rename these commonly used functions, for consistency. Also add function comments in common.h. Suggested-by: NWolfgang Denk <wd@denx.de> Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
We are now using an env_ prefix for environment functions. Rename setenv() for consistency. Also add function comments in common.h. Suggested-by: NWolfgang Denk <wd@denx.de> Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Peng Fan 提交于
Fix build warning when CONFIG_IMX_RDC not defined in defconfig. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com>
-
由 Peng Fan 提交于
Simplify code by removing set_preclk_from_osc with directly setbits_le32. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com>
-
由 Peng Fan 提交于
As M4 is sourcing UART clk from OSC, to make UART work when M4 is enabled, need to select OSC as clk parent, 24M OSC is enough for debug UART in uboot. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com>
-
由 Peng Fan 提交于
There is not LDO_SOC/PU/ARM/MMDC1 on i.MX6SLL, also no need to gate/ungate all PFDs to make PFD working. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com>
-
由 Peng Fan 提交于
Select ARM_ERRATA_845369 for i.MX6DQ/DL/QP. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
Under very rare timing circumstances, transitioning into streaming mode might create a data corruption. Present on Two or more processors or 1 core with ACP, all revisions. This erratum can be worked round by setting bit[22] of the undocumented Diagnostic Control Register to 1. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@konsulko.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
The ARM errata 751472, 794072, 761320 only applied to the following configuration: This erratum affects configurations with either: - One processor if the ACP is present - Two or more processors i.MX6 family does not have the ACP and thus only the MPCore system will be impacted, which are the i.MX6DQ, i.MX6DL, and i.MX6QP. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com>
-
由 Sébastien Szymanski 提交于
i.MX6ULL has different speed grades than i.MX6UL. Signed-off-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>
-
由 Sébastien Szymanski 提交于
Return the correct value when the speed grade is 696MHz. Signed-off-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>
-
由 Breno Lima 提交于
The IPU AXI QoS for the i.MX6QP and i.MX6DP processors have to be set as commented in the code: /* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */ Set IOMUXC_GPR6 and IOMUXC_GPR7 to 0x77177717 instead of 0x007F007F. Signed-off-by: NBreno Lima <breno.lima@nxp.com>
-
由 Breno Lima 提交于
The IPU AXI QoS for the i.MX6QP and i.MX6DP processors have to be set as commented in the code: /* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */ Set IOMUXC_GPR6 and IOMUXC_GPR7 to 0x77177717 instead of 0x007F007F. Signed-off-by: NBreno Lima <breno.lima@nxp.com>
-
由 Anatolij Gustschin 提交于
This appear to be a copy-paste error, clean it up. Signed-off-by: NAnatolij Gustschin <agust@denx.de> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
由 Anatolij Gustschin 提交于
Select SION by appropriate macro instead of constant. Signed-off-by: NAnatolij Gustschin <agust@denx.de> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
由 Simon Glass 提交于
Use the env_save() function directly now that there is only one implementation of saveenv(). Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NWolfgang Denk <wd@denx.de> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
This is a strange name for a function that loads the environment. There is now only one implementation of this function, so use the new env_load() function directly instead. Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
We only have a single implementation of this function now and it is called env_get_char(). Drop the old function and the weak version. Reviewed-by: NTom Rini <trini@konsulko.com> Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Now that env_init() is only defined once we can drop the env_init_new() name and just use env_init(). Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
This variable is declared as a global in most environment location drivers. But it is not used outside the drivers and most of the declarations are unnecessary. Also some drivers call free() on env_ptr which seems wrong since it is not in the heap. Drop the variable where possible, and all calls to free(). Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
Add a name to the driver and use that instead of the global variable declared by each driver. Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
Most of the init() implementations just use the default environment. Adjust env_init_new() to do this automatically, and drop the redundant code. Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
Move over to use a the master implementation of the location drivers, with each method calling out to the appropriate driver. Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
We plan to move to a environment access via drivers for each location where the environment can be stored. Add an implementation for this. So far it is not used, but will be pressed into service in a future patch. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
At present we support multiple environment drivers but there is not way to select between them at run time. Also settings related to the position and size of the environment area are global (i.e. apply to all locations). Until these limitations are removed we cannot really support more than one environment location. Adjust the location to be a choice so that only one can be selected. By default the environment is 'nowhere', meaning that the environment exists only in memory and cannot be saved. Also expand the help for the 'nowhere' option and move it to the top since it is the default. Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: Move all of the imply logic to default X if Y so it works again] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Marcel Ziswiler 提交于
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Marcel Ziswiler 提交于
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-