- 23 11月, 2014 1 次提交
-
-
由 Masahiro Yamada 提交于
Since commit 0defddc8 (config: Add a default CONFIG_SYS_PROMPT), each board header does not need to define CONFIG_SYS_PROMPT as long as it uses the default prompt "=> ". Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
- 21 11月, 2014 5 次提交
-
-
由 Masahiro Yamada 提交于
CONFIG_CPU_ARM1136 was introduced into Kconfig by commit 2e07c249 (kconfig: arm: introduce symbol for ARM CPUs). This commit removes all the defines of CONFIG_ARM1136 and replaces the only reference in arch/arm/lib/cache.c with CONFIG_CPU_ARM1136. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
CONFIG_CPU_ARM926EJS was introduced into Kconfig by commit 2e07c249 (kconfig: arm: introduce symbol for ARM CPUs). This commit removes all the defines of CONFIG_ARM926EJS and replaces the only reference in arch/arm/lib/cache.c with CONFIG_CPU_ARM926EJS. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
CONFIG_CPU_ARM920T was introduced into Kconfig by commit 2e07c249 (kconfig: arm: introduce symbol for ARM CPUs). This commit removes all the defines of CONFIG_ARM920T and replaces the only reference in drivers/usb/host/ohci-hcd.c with CONFIG_CPU_ARM920T. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
CONFIG_ARM1176 is defined for some boards but not referenced at all. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Some (not all) of ARMv7 boards define CONFIG_ARMV7, which is useless. Besides, it is never referenced. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
- 19 11月, 2014 4 次提交
-
-
由 Stefan Roese 提交于
a3m071 and a4m2k share one config header. So adding the generic board defines in this one file is enough to convert both boards. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Wolfgang Denk <wd@denx.de>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de> Cc: Wolfgang Denk <wd@denx.de>
-
由 Dirk Eibach 提交于
The gdsys hrcon board is based on a Freescale MPC8308 SOC. It boots from NOR-Flash, kernel and rootfs are stored on SD-Card. On board peripherals include: - 1x GbE (optional) - Lattice ECP3 FPGA connected via eLBC and PCIe Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Dirk Eibach 提交于
Tune dlvision configuration similar to other gdsys boards to reduce memory footprint. Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: NStefan Roese <sr@denx.de>
-
- 17 11月, 2014 12 次提交
-
-
由 Bo Shen 提交于
The code for this board supports following features: - Boot media support: NAND flash/SD card/SPI flash - Support LCD display (optional, disabled by default) - Support ethernet - Support USB mass storage Signed-off-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Bo Shen 提交于
The code for this board supports following features: - Boot media support: NAND flash/SD card/SPI flash - Support LCD display - Support ethernet - Support USB mass storage Signed-off-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Heiko Schocher 提交于
replaces the at91bootstrap code with SPL code. make the spl image with: ./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin this writes the length of the spl image into the 6th execption vector. This is needed from the ROM bootloader. Signed-off-by: NHeiko Schocher <hs@denx.de> Reviewed-by: NBo Shen <voice.shen@atmel.com> Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Heiko Schocher 提交于
replaces the at91bootstrap code with SPL code. make the spl image with: ./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin this writes the length of the spl image into the 6th execption vector. This is needed from the ROM bootloader. Signed-off-by: NHeiko Schocher <hs@denx.de> Reviewed-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de> Reviewed-by: NBo Shen <voice.shen@atmel.com> Reviewed-by: NJagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Heiko Schocher 提交于
move CONFIG_SYS_SPI_WRITE_TOUT into drivers/spi/atmel_spi.h and define a default value. Delete this define in the board config files, where it is possible (all boards use currently the same value). Signed-off-by: NHeiko Schocher <hs@denx.de> Reviewed-by: NJagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Bo Shen 提交于
Signed-off-by: NBo Shen <voice.shen@atmel.com> Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Scott Jiang 提交于
Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>
-
由 Scott Jiang 提交于
Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>
-
由 Nobuhiro Iwamatsu 提交于
Common part of config for lager, koelsch, alt and gose board will be able to replace rcar-gen2-common.h. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
The lager, koelsch, alt, gose board supported in rmobile is distinguished as the R-Car Gen2 series and has much common setting. This collect up the common part of config as rcar-gen2-common.h. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This moves SH_32BIT to Kconfig, and removes SH_32BIT from config files. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
- 15 11月, 2014 7 次提交
-
-
由 Yangbo Lu 提交于
Enable these boards mtdparts for nor flash: p1020rdb-pd, p1021rdb-pc, p1022ds, p1025twr, and p2020rdb-pc. Signed-off-by: NXie Xiaobo <X.Xie@freescale.com> Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Scott Wood <scottwood@freescale.com>
-
由 Valentin Longchamp 提交于
This converts all the Keymile powerpc boards to the generic board initialization. This includes the 3 Keymile powerpc subsystems: km82xx, km83xx, and kmp204x. Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 Ashish Kumar 提交于
* fdt_fixup_mtdparts is called from ft_board_setup * Run "mtdparts default" to create NAND partition on uboot * Use mtdparts to create partitions dynamically rather than using static partitions in device tree Signed-off-by: NAshish Kumar <Ashish.Kumar@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 Ashish Kumar 提交于
* fdt_fixup_mtdparts is called from ft_board_setup * run "mtdparts default" to create NAND, NOR partition on uboot * Use mtdparts to create partitions dynamically rather than using static partitions in device tree Signed-off-by: NAshish Kumar <Ashish.Kumar@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 Chunhe Lan 提交于
This support of CPLD includes - Files and register definitions - Command to switch alternate bank - Command to switch default bank Signed-off-by: NChunhe Lan <Chunhe.Lan@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 Paul Gortmaker 提交于
Tested on the following baseline (note "dirty" since I enabled ALT_BOOT in the config in order to use the alternate boot bank.) Everything seems to work fine with no additional changes. The banner warning message is now gone. --- U-Boot 2014.10-rc1-00075-ge49f14af-dirty (Aug 14 2014 - 10:26:15) CPU: 8548E, Version: 2.1, (0x80390021) Core: e500, Version: 2.2, (0x80210022) Clock Configuration: CPU0:990 MHz, CCB:396 MHz, DDR:198 MHz (396 MT/s data rate), LBC:99 MHz L1: D-cache 32 KiB enabled I-cache 32 KiB enabled I2C: ready DRAM: Detected UDIMM SDRAM: 128 MiB 256 MiB (DDR2, 64-bit, CL=3, ECC off) Flash: 72 MiB L2: 512 KiB enabled *** Warning - bad CRC, using default environment PCI: Host, 64 bit, 66 MHz, sync, arbiter 00:01.0 - 8086:1026 - Network controller PCI1: Bus 00 - 00 PCIe1: Root Complex, x1 gen1, regs @ 0xe000a000 02:00.0 - 1148:9e00 - Network controller PCIe1: Bus 01 - 02 In: serial Out: serial Err: serial Net: eTSEC0 [PRIME], eTSEC1 Hit any key to stop autoboot: 0 => ver U-Boot 2014.10-rc1-00075-ge49f14af-dirty (Aug 14 2014 - 10:26:15) powerpc-linux-gcc (GCC) 4.5.2 GNU ld (GNU Binutils) 2.21 => --- Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 Valentin Longchamp 提交于
Until now this defined to be 512KB and the total binary size actually was on the edge of this limit. Most of the powerpc boards have thus moved to 768KB. Since on the current kmp204x boards there is 1MB reserved for u-boot on the SPI boot flash, there is no problem to set the limit to 768KB as well to be on line with the other powerpc boards and to eventually configure in some additional features (and binary size) to u-boot. Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
- 14 11月, 2014 1 次提交
-
-
由 Soeren Moch 提交于
Add initial support for TBS2910 Matrix ARM miniPC. Support includes MMC, Ethernet, UARTs, HDMI, USB, SATA, PCI, I2C, RTC. Signed-off-by: NSoeren Moch <smoch@web.de>
-
- 13 11月, 2014 10 次提交
-
-
由 John Tobias 提交于
add the spl info in the header file. Also, added a macro statement in m6sabre_common.h to avoid compiler warning. Signed-off-by: NJohn Tobias <john.tobias.ph@gmail.com>
-
由 Ye.Li 提交于
The i.MX6Q/DL sabreauto board has one NAND socket, set the CONFIG_NAND_MXS and relevant NAND configurations to enable the MXS NAND flash driver. Add board level codes to set IOMUX and clock for GPMI-NAND and BCH module. Signed-off-by: NYe.Li <B37916@freescale.com> Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Ye.Li 提交于
Set the CONFIG_ENV_OFFSET from 384KB to 512KB offset, so we will have larger space for u-boot image. When enabling NAND flash support feature, the u-boot image size has exceeded the 384KB, which causes overlay to the environment variables storage. Signed-off-by: NYe.Li <B37916@freescale.com> Acked-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
Since kernel 3.15 there are two dtb's for the imx53-qsb board: imx53-qsb.dtb - For the boards with DA9053 PMIC imx53-qsrb.dtb - For the boards with MC34708 PMIC Change the 'fdt_file' dynamically, so that the correct dtb can be used depending on the board variant. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Acked-by: NOtavio Salvador <otavio@ossystems.com.br>
-
由 Christian Gmeiner 提交于
U-Boot 2014.10-17457-g0b23780f-dirty (Nov 10 2014 - 11:41:04) CPU: Freescale i.MX6D rev1.2 at 792 MHz Reset cause: WDOG Board: ot1200 I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 SF: Detected M25P16 with page size 256 Bytes, erase size 64 KiB, total 2 MiB In: serial Out: serial Err: serial Net: using phy at 0 FEC [PRIME] Hit any key to stop autoboot: 0 => usb start (Re)start USB... USB0: Port not available. USB1: USB EHCI 1.00 scanning bus 1 for devices... 4 USB Device(s) found => usb tree USB device tree: 1 Hub (480 Mb/s, 0mA) | u-boot EHCI Host Controller | +-2 Hub (480 Mb/s, 2mA) | +-3 Mass Storage (480 Mb/s, 80mA) | USBest Technology USB Mass Storage Device 0000000000028B | +-4 Vendor specific (480 Mb/s, 2mA) => Signed-off-by: NChristian Gmeiner <christian.gmeiner@gmail.com>
-
由 Hans de Goede 提交于
Add support for the 2 ehci controllers found on the sun6i (A31) soc. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk> Acked-by: NMarek Vasut <marex@denx.de>
-
由 Hans de Goede 提交于
Add proper Kconfig options to select the usb Vbus gpio-s, besides moving to Kconfig being the right thing to do, an added advantage of this is that it allows for boards without Vbus gpio-s. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
Add clock_init_safe and clockset_pll5 functions, as these are needed for SPL support resp. DRAM init (which is needed for SPL too). Also add some extra clock register constant defines. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Michal Simek 提交于
This is a MIME GnuPG-signed message. If you see this text, it means that your E-mail or Usenet software does not support MIME signed messages. The Internet standard for MIME PGP messages, RFC 2015, was published in 1996. To open this message correctly you will need to install E-mail or Usenet software that supports modern Internet standards. Move CONFIG_DEFAULT_DEVICE_TREE from board config directly to defconfig. This patch removes compilation warning: include/configs/zynq_zybo.h:24:0: warning: "CONFIG_DEFAULT_DEVICE_TREE" redefined [enabled by default] #define CONFIG_DEFAULT_DEVICE_TREE zynq-zybo Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Masahiro Yamada 提交于
This commit moves CONFIG_SH2, CONFIG_SH2A, CONFIG_SH3, CONFIG_SH4 to Kconfig renaming into CONFIG_CPU_SH2, CONFIG_CPU_SH2A, CONFIG_CPU_SH3, CONFIG_CPU_SH4, respectively because arch/sh/Kconfig of Linux uses CONFIG_CPU_SH* convention. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-