- 30 1月, 2018 35 次提交
-
-
由 Michal Simek 提交于
Ethernet is not enabled that's why this alias should be completely unused. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
The same change is done for others zynq boards to get uart as early as possible. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Updating year in zynq files. Also add missing Copyright to board.c. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Add low level initialization for zcu102-rev1.0. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Move generic functions to common location psu_spl_init.c. Function declarations are added to private header. These changes are done in connection to the fact that still files from HDF can be copied over and compilation should pass. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Remove SPL_BUILD dependency from zynqmp.c and move it to header file. Use only one symbol for including psu_init. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Remove functions which are no longer renerated by PCW. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Ezequiel Garcia 提交于
The Arasan NFC driver requires the self-init mode, so it should select it. Instead of having the config header define the macro, it's cleaner to select the option at the Kconfig level. Signed-off-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
This patch corrects the ecc address calculation before updating to ecc register. The ecc address has to be calculated based on page, oob and ecc sizes of the device. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
This patch adds support for ondie ecc. As of now this adds support for micron parts which supports ondie ecc. Didn't found any better way to detect ondie ecc support by a device except sorting out with manufacture and device id's. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
Move common part of ecc structure initialization to arasan_nand_init() routine. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
This patch adds new target which is called as mini configuration with only emmc functionality and other required basic features enabled. This will be used to run in system with small footprint and needs emmc support. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
This patch adds new target which is called as mini configuration with only nand functionality and other required basic features enabled. This will be used to run in system with small footprint and needs nand support. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
DDR less systems are possible for configuration like mini qspi and making DDR region as normal memory may cause speculative access which results u-boot hang if DDR is absent. So, this patch fixes the issue by not making DDR memory region entry into MMU table. Future solution is to prepare MMU table per memory node in dts instead of hard code DDR addresses. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
psu_init() returns int which wasn't declared and checked. The patch is fixing function declarations and code to handle return values properly. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Remove additional spaces before comment. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Drop the space before/after '<' and '>'; and separate the entries to be a bit more readable. Reported-by: NJulia Cartwright <julia@ni.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
BOOTCOMMAND is composed with distro_bootcmd but this variable is not present. Enabling distro defaults setting is fixing it. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
It will cleanup generic config and enable option to change it for every board. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
There are two reasons for doing this change. There is still !DM driver for xilinx soft gpio IP and especially it is saving some space for memory constrained boards like cse (almost ~400B). Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Do not enable DM_ETH/MMC if subsystems are not enabled. This saves memory for memory constrained boards like cse. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
There is no reason to enable BLK by default for all boards which is just increasing memory footprint for memory contrained boards like cse. zc770s are also saving some space. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Ethernet cable is not connected for xm011 that's why disable all ethernet related configurations. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Wire debug console which is useful for early debugging. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
It is good to see this string to make sure that u-boot which runs on the board is the same which should run there. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Anders Hedlund 提交于
Set the 8GB PCIe High area as device memory. Also extend the DDR High area to cover the full 32GB range. Signed-off-by: NAnders Hedlund <anders.j.hedlund@gmail.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
Add check if boot_targets exists in environment and then generate new_targets env accordingly. Performing strlen on null address causes it to fail with exception if isolation is enabled with DDR address zero as secure. It works with out isolation enabled as zero is valid address but it may lead to junk values in boot_targets. This patch fixes the issue by checking return value of env_get so that it generate boot_targets properly. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Masahiro Yamada 提交于
These are defined, but not referenced at all. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
The patch is fixing the following Warning: arch/arm/mach-zynq/ps7_spl_init.c:133:24: warning: comparison between signed and unsigned integer expressions [-Wsign-compare] while (ioread(addr) < delay) ^ Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
zc770-xm011 is x8 width configuration. This FMC card has also x16 variant which requires different ps7_init configuration. This patch adds it. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Simplify ps7_init* initialization. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Simplify ps7_init* initialization. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Simplify ps7_init* initialization. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Simplify ps7_init* initialization. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
zc770-xm011 is also added and supported. Reflect this in README. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 24 1月, 2018 2 次提交
-
-
由 Ezequiel Garcia 提交于
NAND and QSPI devices are now supported, so mark them as such. Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Ezequiel Garcia 提交于
Setup proper dependency in Kconfig for SPL_CLK. If SPL is not enabled, SPL_CLK shouldn't be selected. Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 17 1月, 2018 1 次提交
-
-
由 Tom Rini 提交于
In some cases when "more" is told to page a given file it will prepend the output with: :::::::::::::: /PATH/TO/THE/FILE :::::::::::::: And when this happens the output will not match the expected length. Further, if we use a different pager we will instead fail the coverage tests as we will not have 100% coverage. Update the help test to remove the string in question. Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 16 1月, 2018 2 次提交
-
-