- 29 6月, 2017 6 次提交
-
-
由 Heiko Schocher 提交于
since commit: f8b7fff1 "serial: atmel_usart: Add clk support" smartweb board comes not up anymore. Fix it. Signed-off-by: NHeiko Schocher <hs@denx.de> Acked-by: NWenyou Yang <wenyou.yang@microchip.com>
-
由 Heiko Schocher 提交于
fix warnings: drivers/usb/gadget/at91_udc.c:1344:12: warning: 'at91rm9200_udc_init' defined but not used [-Wunused-function] drivers/usb/gadget/at91_udc.c:1379:13: warning: 'at91rm9200_udc_pullup' defined but not used [-Wunused-function] drivers/usb/gadget/at91_udc.c:1476:12: warning: 'at91sam9263_udc_init' defined but not used [-Wunused-function] Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Peter Robinson 提交于
The CONFIG_DEFAULT_FDT_FILE expects just the file not a full path as that might vary depending on the variant of Linux distro you might be using. Cc: Martin Donnelly <martin.donnelly@ge.com> Cc: Fabio Estevam <festevam@gmail.com> Signed-off-by: NPeter Robinson <pbrobinson@gmail.com> Acked-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Bin Meng 提交于
Some Kconfig options are defined in a line with leading spaces/tabs. Update build-whitelist/check-config scripts to handle such cases. Generate a new config_whitelist.txt with new scripts. Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Andy Yan 提交于
The origin SPL_USE_ARCH_MEMSET/MEMCPY use same prompt message as USE_ARCH_MEMSET/MEMCPY, which makes it's hard to distinguish them in menuconfig interface. This patch gives them different prompt messages for spl and none-spl config. Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
-
由 Lukasz Majewski 提交于
After the commit SHA1: 842778a0 - the serial number descriptor is only visible when we have non zero length of g_dnl_serial. However, on some platforms (e.g. Siemens) the serial number is set at g_dnl_bind_fixup(), so with the current code we will always omit the serial (since it is not set). This commit moves the g_dnl_bind_fixup() call before the g_dnl_serial length test. Signed-off-by: NLukasz Majewski <lukma@denx.de> Acked-by: NHeiko Schocher <hs@denx.de> Tested-by: NHeiko Schocher <hs@denx.de>
-
- 28 6月, 2017 1 次提交
-
-
由 Tom Rini 提交于
The ti816x SoC revision of the ethernet IP block is handled by the "davinci_emac" driver, rather than the "cpsw" driver as done by later members of the family. Enable the relevant plumbing. Signed-off-by: NSriramakrishnan <srk@ti.com> Signed-off-by: NVitaly Wool <vitaly.wool@konsulko.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 27 6月, 2017 5 次提交
-
-
-
git://www.denx.de/git/u-boot-imx由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
-
由 Bin Meng 提交于
This reverts commit ddb3ac3c. With MMC converted to driver model, SCSI driver is broken due to zero address access at (ops->read) in block_dread() function. The fix (SCSI driver converted to DM) is ready in u-boot-dm branch, but it is too late for this relese to get that in. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Fabio Estevam 提交于
The correct name is 'Celsius', so fix it accordingly. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
-
-
- 26 6月, 2017 1 次提交
-
-
由 Masahiro Yamada 提交于
These are only used in drivers/mis/i2c_eeprom.c Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
- 25 6月, 2017 5 次提交
-
-
git://git.denx.de/u-boot-uniphier由 Tom Rini 提交于
- fix sparse warnings - sync DT with Linux - add new board support (LD11/LD20 global)
-
由 Kunihiko Hayashi 提交于
Add initial device tree support for LD20 Global board. Signed-off-by: NKunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Kunihiko Hayashi 提交于
Add initial device tree support for LD11 Global board. Signed-off-by: NKunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Fix warnings reported by sparse: - ... was not declared. Should it be static?" - cast to restricted __be32 While fixing those, the type conflict of cci500_init() was found. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
- 23 6月, 2017 22 次提交
-
-
-
由 Kever Yang 提交于
According to rk3036 TRM, pll_con1[12] should be set to '1' for the pll integer mode, while the '0' means the frac mode. Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Kever Yang 提交于
The maximum spl_size for rk3399 is the internal memory size minus the size used in bootrom (which usually can get from SPL_TEXT_BASE). Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Kever Yang 提交于
The SPL_MAX_SIZE is the internal memory size minux the space used by bootrom. Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Tom Rini 提交于
This function is unused, remove. Reported by clang-3.8. Fixes: a1c29d4b ("rockchip: mkimage: set init_boot_size to avoid ...") Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Heiko Schocher 提交于
since commit: f8b7fff1 "serial: atmel_usart: Add clk support" corvus board comes not up anymore. Fix it. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Philipp Tomsich 提交于
Adding myself to MAINTAINERS and git-mailrc for the rockchip sub-architecture. Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Heiko Schocher 提交于
fix menutext for the options SPL_DM_SERIAL and TPL_DM_SERIAL. Both have the same text as DM_SERIAL, which is confusing. Signed-off-by: NHeiko Schocher <hs@denx.de> Reviewed-by: NStefan Roese <sr@denx.de>
-
由 Heiko Schocher 提交于
for debugging it is handy to know the fdt_blob address. So print it in bdinfo. Signed-off-by: NHeiko Schocher <hs@denx.de> Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Rob Clark 提交于
Otherwise the loaded image would miss the efi_runtime sections, and fall over hard when grub (for example) tried to call runtime services located in this section. Signed-off-by: NRob Clark <robdclark@gmail.com>
-
由 Ladislav Michl 提交于
commit dfe64e2c Author: Sergey Lapin <slapin@ossfans.org> Date: Mon Jan 14 03:46:50 2013 +0000 mtd: resync with Linux-3.7.1 modified onenand_block_markbad to call mtd_block_markbad, but as _block_markbad function pointer used by mtd_block_markbad to do actual job is by default pointing back to onenand_block_markbad there is no way this function ever finishes its job. Fix it by changing function body according current (4.12-rc6) linux implementation. Tested on IGEPv2 board with Muxed OneNAND(DDP) 512MB containing several unerasable blocks this function marked bad. Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
-
由 Ladislav Michl 提交于
Current implementation is unable to access second half of DDP OneNAND flash (reads first half mirrored). Use block and bufferram address calculations from onenand_base to fix this. Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
-
由 Ladislav Michl 提交于
Do not call onenand_spl_get_geometry() for each block read. Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
-
由 Emmanuel Vadot 提交于
Define a default number of 1 for mmc max device if board config didn't specify one. Signed-off-by: NEmmanuel Vadot <manu@bidouilliste.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Tom Rini 提交于
The variables gpll_init_cfg and apll_init_cfg are unused in this file, remove them. Cc: Simon Glass <sjg@chromium.org> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Tom Rini 提交于
The variable syndrome_codes is only used when DEBUG is define, add #if guards around it in the same style as the rest of the file. Cc: Stefan Roese <sr@denx.de> Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NStefan Roese <sr@denx.de>
-
由 Tom Rini 提交于
On the controlcenterd_36BIT_SDCARD config we get a warning about prg_stage1_prepare being unused. Move the declaration closer to usage and hide under the existing #if tests. Cc: Dirk Eibach <eibach@gdsys.de> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Lokesh Vutla 提交于
Now that we can specify DT nodes that can be used in spl, mark all necessary nodes as u-boot,dm-spl. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Lokesh Vutla 提交于
Now that we can specify DT nodes that can be used in spl, mark all necessary nodes as u-boot,dm-spl. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
It has been observed that between PG1.0 and PG2.0/2.1 depending on which device we boot from, we may see a different value here than is documented in the TRM. Update the values for NAND and MMC1 based on real life usage on each revision. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Semen Protsenko 提交于
Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org> Reviewed-by: NTom Rini <trini@konsulko.com>
-
-