Based on ST-Ericsson internal git repo.
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NJohn Rigby <john.rigby@linaro.org>
CC: Albert Aribaud <albert.aribaud@free.fr>

Add a header file with the missing function prototype to fix

ca9x4_ct_vxp.c: In function 'cpu_mmc_init':
ca9x4_ct_vxp.c:93: warning: implicit declaration of function 'arm_pl180_mmci_init'

introduced by commit "ARMV7: Vexpress: Add MMC support"
(f0c64526)
Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Matt Waddel <matt.waddel@linaro.org>

We change default settings for egiga on mgcoge3un.
The reason we need this is that we have the gig port on mgcoge3un
connected using a back-to-back pair of PHYs. There are no magnetics and
because of that the port has to be run with a fixd configuration and
auto-negotiation must be disabled. In the default mode the egiga driver
uses autoneg to determine port speed - which defaults to 1G (we need
100M full duplex).

Add wait for the GPIO line connected to mgcoge3ne before
starting mgcoge3un. A board specific ethernet present function
was added, because on this board ethernet is always present.
The BOCO FPGA access was enhanced and changed to use register
definitions.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

This allows this configuration to be defined differently for some
boards that request it.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

The mgcoge2un target was only an intermediate step to mgcoge3un.
For this reason the mgcoge2un support was moved to mgcoge3un,
because it isn't needed to support both targets.

We add the BootROM init file for the mgcoge3un memphis RAM.

We also move the suen3 and suen8 boards into the correct category
in the MAINTAINERS file.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Acked-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

This is not supported on our km-arm boards since we have defined
CONFIG_SYS_NO_FLASH for our NAND Flash chip.

With CONFIG_CMD_JFFS2, the ls command is present and works very badly
on our km-arm boards.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Acked-by: NHeiko Schocher <hs@denx.de>
Acked-by: NPrafulla Wadaskar <prafulla@marvell.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>

This environment variable is used to set the bootcount address
for the kernel.

last_stage_init is not available for arm platforms. So the
calls to set_km_var and set_bootcount_addr are done in
misc_init_r.

Additionally some unneeded printouts were removed.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Acked-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

Since all the boards define the same env settings, this simplifies
the board files.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

This define is marvell specific, so it should be present in km_arm.
It is however not needed there either, since we set it to the default
value that is already set in include/asm/arch-kirkwood/config.h
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>

Added MMC SPL boot support for SMDKV310. This framework design is
based on nand_spl support.
Signed-off-by: NChander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

SMDKV310 board is based on Samsung S5PV310 SOC. This SOC is very much
similar to S5PC210.
Signed-off-by: NChander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

The source of pwm clock is fixed at evt1.
And some registers for pwm clock are removed.
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

This patch added set_mmc_clk for external clock control.

c210 didn't support host clock control.
So We need external_clock_control function for c210.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>

S5PC210 SoC have two cpu revisions, and have some difference.
So, support the cpu revision for each revision.
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>

SROM config code is made common for S5P series of boards.
smdkc100.c now refers to s5p-common/sromc.c for SROM related
subroutines.
Signed-off-by: NChander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

Since we rename _end to __bss_end__, But we need add _end symbol for
the end of u-boot image.
Signed-off-by: NZhong Hongbo <bocui107@gmail.com>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

Fix typo resulting in the compilation error

s5p_mmc.c: In function 's5p_mmc_initialize':
s5p_mmc.c:469: error: 'struct mmc' has no member named 'm_bmax'

introduced by commit "MMC: make b_max unconditional"
(8feafcc4)
Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
CC: John Rigby <john.rigby@linaro.org>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

S5PC2XX: Macro values for Pull Up and Driver Strength were wrong.
S5PC1XX: Macro values for Driver Strength were wrong.
Signed-off-by: NChander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

Signed-off-by: NDavid Müller <d.mueller@elsoft.ch>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

Signed-off-by: NDavid Müller <d.mueller@elsoft.ch>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

Signed-off-by: NDavid Müller <d.mueller@elsoft.ch>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

Signed-off-by: NDavid Müller <d.mueller@elsoft.ch>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

Without this patch, you should get a warning.
Signed-off-by: NJason Kridner <jkridner@beagleboard.org>
Acked-by: NDirk Behme <dirk.behme@de.bosch.com>

Before the actual initialization do a hard reset of the SATA port and the
connected device.

changes v1->v2:
 - add comment for udelay
Signed-off-by: NMichael Walle <michael@walle.cc>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>

Signed-off-by: NDavid Müller <d.mueller@elsoft.ch>

Signed-off-by: NStefano Babic <sbabic@denx.de>

Signed-off-by: NStefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>

get_reset_cause() should not be exported. Drop code in the function
after return statement that can generate warnings due to unreachable code.
Signed-off-by: NStefano Babic <sbabic@denx.de>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

commit ed59e587 (Remove device tree booting dependency on CONFIG_SYS_BOOTMAPSZ) made the
definition of CONFIG_SYS_BOOTMAPSZ unnecessary.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NJason Liu <jason.hui@linaro.org>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

The boot cause code has been factor out to soc common
code,we need drop the part from the board support code

This patch also remove the redundant cpu version print
Signed-off-by: NJason Liu <jason.hui@linaro.org>

config.mk should not be used in board directory and should be removed.
Use the same approach for building the image as other MX51/MX53 boards.

After this change vision2 board can be built again.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

Currently the fb_videomode struct is only declared if CONFIG_HW_WATCHDOG is defined.

Remove this dependancy and let the video struct always be declared.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

This patch add initial support for freescale MX53LOCO board.
Network(FEC),SD/MMC,UART have been supported by this patch
Signed-off-by: NJason Liu <jason.hui@linaro.org>

With the following commit, CONFIG_OF_LIBFDT is redefined.

  2fa8ca98
  Add CONFIG_OF_LIBFDT to more boards.

Remove the duplicated definition to fix CONFIG_OF_LIBFDT redefined
warning.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Since the following commit, definition CONFIG_SYS_BOOTMAPSZ is not
needed any more.

  ed59e587
  Remove device tree booting dependency on CONFIG_SYS_BOOTMAPSZ
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

No need to use '#define SYMBOL 1' to make it active.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>