Enable networking for EP108 by default.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Enable gem0 and setup phy addr for EP.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Based on the patch:
"armv8: caches: Added routine to set non cacheable region"
(sha1: dad17fd5)
it is necessary to add platform specific hook.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Enable Secure IOU setup to enable U-Boot to run in EL3 without
setting from ATF.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

We have flipped CONFIG_SPL_DISABLE_OF_CONTROL.  We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:

 #ifdef CONFIG_OF_CONTROL
 # if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
 #  define OF_CONTROL 0
 # else
 #  define OF_CONTROL 1
 # endif
 #else
 # define OF_CONTROL 0
 #endif

Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute.  It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.

Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

As we discussed a couple of times, negative CONFIG options make our
life difficult; CONFIG_SYS_NO_FLASH, CONFIG_SYS_DCACHE_OFF, ...
and here is another one.

Now, there are three boards enabling OF_CONTROL on SPL:
 - socfpga_arria5_defconfig
 - socfpga_cyclone5_defconfig
 - socfpga_socrates_defconfig

This commit adds CONFIG_SPL_OF_CONTROL for them and deletes
CONFIG_SPL_DISABLE_OF_CONTROL from the other boards to invert
the logic.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

There is no case where defined(SPL_DISABLE_OF_CONTROL) is true.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

We do not want to compile the DM remove code for SPL.  Currently,
we undef it in include/config_uncmd_spl.h (for C files) and in
scripts/Makefile.uncmd_spl (for Makefiles).  This is really ugly.

This commit demonstrates how we can deprecate those two files.

Use $(SPL_) for the entry in the Makfile and CONFIG_IS_ENABLED()
in C files.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NStefano Babic <sbabic@denx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NStefano Babic <sbabic@denx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NStefano Babic <sbabic@denx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Just preparing for upcoming cleaning.

The board-specific linker script  board/vpac270/u-boot-spl.lds
has been touched to avoid build error.  It does not change the
size of spl/u-boot-spl.bin for this board, so it should be OK.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NStefano Babic <sbabic@denx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

The previous commit introduced a useful macro used in makefiles,
in order to reference to different variables (CONFIG_... or
CONFIG_SPL_...) depending on the build context.

Per-image config option control is a PITA in C sources, too.
Here are some macros useful in C/CPP expressions.

CONFIG_IS_ENABLED(FOO) can be used as a shorthand for

  (!defined(CONFIG_SPL_BUILD) && defined(CONFIG_FOO)) || \
   (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_FOO))

For example, it is useful to describe C code as follows,

  #if CONFIG_IS_ENABLED(OF_CONTROL)
      (device tree code)
  #else
      (board file code)
  #endif

The ifdef conditional above is switched by CONFIG_OF_CONTROL during
the U-Boot proper building (CONFIG_SPL_BUILD is not defined), and by
CONFIG_SPL_OF_CONTROL during SPL building (CONFIG_SPL_BUILD is
defined).

The macro can be used in C context as well, so you can also write the
equivalent code as follows:

  if (CONFIG_IS_ENABLED(OF_CONTROL)) {
      (device tree code)
  } else {
      (board file code)
  }

Another useful macro is CONFIG_VALUE().
CONFIG_VALUE(FOO) is expanded into CONFIG_FOO if CONFIG_SPL_BUILD is
undefined, and into CONFIG_SPL_FOO if CONFIG_SPL_BUILD is defined.

You can write as follows:

  text_base = CONFIG_VALUE(TEXT_BASE);

instead of:

  #ifdef CONFIG_SPL_BUILD
      text_base = CONFIG_SPL_TEXT_BASE;
  #else
      text_base = CONFIG_TEXT_BASE;
  #endif

This commit also adds slight hacking on fixdep so that it can
output a correct list of fixed dependencies.

If the fixdep finds CONFIG_IS_ENABLED(FOO) in a source file,
we want
    $(wildcard include/config/foo.h)
in the U-boot proper building context, while we want
    $(wildcard include/config/spl/foo.h)
in the SPL build context.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Commit e02ee254 ("kconfig: switch to single .config
configuration") made the configuration itself pretty simple,
instead, we lost the way to systematically enable/disable config
options for each image independently.

Our current strategy is, put entries into Makefile.spl for options
we need separate enabling, or once enable the options globally in
Kconfig and then undef them in Makefile.uncmd_spl if we do not want
to compile the features for SPL at all.  Things are getting really
messy.  Besides, "ifdef CONFIG_SPL_BUILD" are sprinkled everywhere
in makefiles.

This commit adds a variable to help describe makefile simpler.

$(SPL_) evaluates to "SPL_" during the SPL build, while to an empty
string during building U-boot proper.

So, you can write

  obj-$(CONFIG_$(SPL_)FOO) += foo.o

instead of

  ifdef CONFIG_SPL_BUILD
  obj-$(CONFIG_SPL_FOO) += foo.o
  else
  obj-$(CONFIG_FOO) += foo.o
  endif

If CONFIG_SPL_FOO does not exist in Kconfig, it is equivalent to

  ifndef CONFIG_SPL_BUILD
  obj-$(CONFIG_SPL_FOO) += foo.o
  endif

This is the pattern we often see in our current makefiles.

To take advantage of this macro, we should prefix SPL_ for the SPL
version of the option when we need independent control between
U-boot and SPL.  With this naming scheme, I hope our makefiles will
be much simplified.

It means we want to rename existing config options as follows
in the long run:

  CONFIG_SPL_SERIAL_SUPPORT     -> CONFIG_SPL_SERIAL
  CONFIG_SPL_I2C_SUPPORT        -> CONFIG_SPL_I2C
  CONFIG_SPL_GPIO_SUPPORT       -> CONFIG_SPL_GPIO
  CONFIG_SPL_SPI_SUPPORT        -> CONFIG_SPL_SPI
  CONFIG_SPL_DISABLE_OF_CONTROL -> CONFIG_SPL_OF_CONTROL
                                      (inverting the logic)

Then drivers/Makefile would be re-worked as follows:

  obj-$(CONFIG_$(SPL_)SERIAL)  += serial/
  obj-$(CONFIG_$(SPL_)I2C)     += i2c/
  obj-$(CONFIG_$(SPL_)GPIO)    += gpio/
  obj-$(CONFIG_$(SPL_)SPI)     += spi/
     ...

Eventually, SPL-specialized entries in Makefile.spl would go away.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

If the target string matches "CONFIG_", move the pointer p
forward.  This saves several 7-chars adjustments.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

- Re-direct stderr into the log files, so any errors U-Boot emits are
  visible in the logs. This is relevant if the "reset" shell command
  attempts to report that it's not supported on the sandbox board.
- Fix test_fs_nonfs() to name the files it created differently for each
  invocation. Otherwise, the logs from different tests overwrite
  each-other.
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Acked-by: NSuriyan Ramasami <suriyan.r@gmail.com>

LPC32xx has 3 I2C bus controllers, 2 of them are used as generic ones
and their parent clock is HCLK and CLK_HI/CLK_LO registers are 10 bit
wide. This means that if HCLK is 104MHz, then minimal configurable I2C
clock speed is about 51KHz.

Only USB OTG I2C bus controller CLK registers are 8 bit wide, thus in
assumption that peripheral clock is 13MHz it allows to set the minimal
bus speed about 25.5KHz.

Check for negative half clock value is removed since it is always false.

The change fixes the following problem for I2C busses 0 and 1:

  => i2c dev 0
  Setting bus to 0
  => i2c speed 100000
  Setting bus speed to 100000 Hz
  Failure changing bus speed (-22)
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Tested-by: NSylvain Lemieux <slemieux@tycoint.com>

The change adds a number of macro definitions used by USB OHCI driver,
if CONFIG_USB_OHCI_LPC32XX is selected from a board config file.
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Tested-by: NSylvain Lemieux <slemieux@tycoint.com>

Incorporate USB driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx USB driver
- lpc3250 header file USB registers definition.

The legacy driver was updated and clean-up as part of the integration with the latest u-boot.
Signed-off-by: NSylvain Lemieux <slemieux@tycoint.com>
Acked-by: NMarek Vasut <marex@denx.de>
Tested-by: NVladimir Zapolskiy <vz@mleia.com>

Updated the LPC32xx I2C driver to support
the OTG I2C that is part of the USB module.
Signed-off-by: NSylvain Lemieux <slemieux@tycoint.com>
Acked-by: NMarek Vasut <marex@denx.de>

Incorporate ECC layout for small page NAND from legacy LPCLinux NXP BSP.
The code taken from the legacy patch is:
- lpc32xx SLC NAND driver (ECC layout for small page)

This layout is matching the lpc32xx NAND SLC Linux Kernel driver.
Signed-off-by: NSylvain Lemieux <slemieux@tycoint.com>

Incorporate NAND SLC hardware ECC support from legacy LPCLinux NXP BSP.
The code taken from the legacy patch is:
- lpc32xx SLC NAND driver (hardware ECC support)
- lpc3250 header file missing SLC NAND registers definition

The legacy driver was updated and clean-up as part of the integration with the existing NAND SLC driver.
Signed-off-by: NSylvain Lemieux <slemieux@tycoint.com>
Tested-by: NVladimir Zapolskiy <vz@mleia.com>

A number of LPC32xx SLC NAND defines is dictated by controller
hardware limits and OOB layout is defined by operating system, the
definitions are common for all users. Since those macro are used
in out of NAND SLC driver code (simple NAND SPL framework), they can
not be placed into the driver, therefore move them from board config
files to arch/config.h

The change also adds OOB layout details specific to small page NAND
devices taken from Linux kernel.
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Tested-by: NSylvain Lemieux <slemieux@tycoint.com>

Incorporate DMA driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx DMA driver
- lpc3250 header file DMA registers definition.

The legacy driver was updated and clean-up as part of the integration with the latest u-boot.
Signed-off-by: NSylvain Lemieux <slemieux@tycoint.com>
Acked-by: NMarek Vasut <marex@denx.de>
Tested-by: NVladimir Zapolskiy <vz@mleia.com>

Signed-off-by: NTom Rini <trini@konsulko.com>

This causes widespread breakage due to the operation of the low-level code
in crt0.S and cro0_64.S for ARM at least.

The fix is not complicated but it seems safer to revert this for now.

This reverts commit 2afddae0.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Enable TI_EDMA3 and SPL_DMA support, so as to reduce boot time. With
DMA enabled there is almost 3x improvement in read performance. This
helps in reducing boot time in qspiboot mode

Also add EDMA3 base address for DRA7XX and AM57XX.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Reviewed-by: NJagan Teki <jteki@openedev.com>

ti_qspi uses memory map mode for faster read. Enabling DMA will increase
read speed by 3x @48MHz on DRA74 EVM.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Reviewed-by: NJagan Teki <jteki@openedev.com>

Signed-off-by: NVignesh R <vigneshr@ti.com>
Reviewed-by: NJagan Teki <jteki@openedev.com>

When doing a memory mapped copy we may have DMA available and thus need
to have this copy abstracted so that the driver can do it, rather than a
simple memcpy.
Signed-off-by: NTom Rini <trini@ti.com>
Signed-off-by: NVignesh R <vigneshr@ti.com>
Reviewed-by: NJagan Teki <jteki@openedev.com>

Adds functions to enable and disable edma3 clocks which can be invoked
by drivers using edma3 to control the clocks.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NJagan Teki <jteki@openedev.com>

Adds functions to enable and disable edma3 clocks which can be invoked
by drivers using edma3 to control the clocks.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NJagan Teki <jteki@openedev.com>

Add do_disable_clocks() to disable clock domains and module clocks.
These clocks are enabled using do_enable_clocks().
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NVignesh R <vigneshr@ti.com>
Reviewed-by: NJagan Teki <jteki@openedev.com>