Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Enable options to permit HDMI output on Odroid-C2 GXBB boards.
Enable VPU Power Domain.
Enable ADC and USB_KERBOARD.
Reviewed-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NAnand Moon <linux.amoon@gmail.com>

Restore CONFIG_ENV_ADDR value to fix boot hang with IFC-NOR
which is default boot source.
Signed-off-by: NAshish Kumar <ashish.kumar@nxp.com>
Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable support to compile SBSA driver.
Signed-off-by: NZhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Add Root Complex and Endpoint mode specific config entries, such that
it's feasible to enable the RC and/or EP mode driver indepently.
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Add TFA secure boot defconfig and Enables secure boot related
configs in it.
Signed-off-by: NManish Tomar <manish.tomar@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CONFIG_BOARD_EARLY_INIT_R for SDHC adapter card
identification and configuration.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable dspi in lx2160aqds tfa defconfig
Enable CONFIG_SPI_FLASH_SST/EON in config file.
Signed-off-by: NZhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable support for sub command 'env info' in sandbox
with CONFIG_CMD_NVEDIT_INFO. This is aimed primarily
at adding unit test.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC
driver can be used for SoC detection.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>

Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC
driver can be used for SoC detection.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>

Add a sandbox SOC driver, and some tests for the SOC uclass.
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>

The Beacon EmbeddedWorks kit is based on the R8A774A1 SoC also
known as the RZ/G2M.

The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi.
Signed-off-by: NAdam Ford <aford173@gmail.com>

Add Kconfig entries for the dc2114x driver and convert various boards.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>

This reverts commit 5d3a21df, reversing
changes made to 56d37f1c.

Unfortunately this is causing CI failures:
https://travis-ci.org/github/trini/u-boot/jobs/711313649Signed-off-by: NTom Rini <trini@konsulko.com>

Add booting from SPI for SiFive Unleashed board.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NBin Meng <bin.meng@windriver.com>
Tested-by: NBin Meng <bin.meng@windriver.com>

Disable ram rockchip debug driver for ROCKPi N8/N10 boards
since we have verified ram in many instances with respective
U-Boot versions.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Enable PCI/NVME for M.2 Slot on RockPI-4 boards.

=> nvme info
Device 0: Vendor: 0x144d Rev: 4L1QCXB7 Prod: S35FNX0J623292
            Type: Hard Disk
            Capacity: 122104.3 MB = 119.2 GB (250069680 x 512)
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Enable common on board devices for ROCKPi N8.

- USB 2.0 Host
- USB 2.0 OTG/Gadget
- HDMI Out
Signed-off-by: NSuniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Enable common on board devices for ROCKPi N10.

- USB 2.0 Host
- USB 3.0 Host
- USB 3.0 Gadget
- HDMI Out
Signed-off-by: NSuniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

ROC-RK3399-PC has specific set of configurations for
on-board led setup.

Due to easiness for user to know the state of the board
roc-rk339-pc board code will setup the low power led
on/off, and waiting for user to press power key and then
glow full power led.

All this needs to happen only during power-on-reset not
for soft reset or WDT.

Also, it is not a proper usage to ask the user to press
the Power key if the board connected remotely, so add
the environment variable 'pwr_key' to check as well.

So, user need to press Power key only
- during POR
- pwr_key=y
Tested-by: NSuniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

roc-rk3399-pc has some specific requirements to support LEDS,
environment. board detection and etc prior to U-Boot proper.

So as of now SPL would be a better stage for these custom board
requirements to support unlike TPL. Adding few of these custom
requirements like LEDS in TPL would require extra code pulling
and also the size of TPL can grow.

So, this patch moves the leds code from TPL into SPL Board init
led_setup code.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>
(split tpl.c change as separate patch)
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>

Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enabled
GPIO pin change compared to 4B, 4C.

So, add or enable difference nodes/properties in 4C dts
by including common dtsi.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Rock PI 4 has 3 variants of hardware platforms called
RockPI 4A, 4B, and 4C.

- Rock PI 4A has no Wif/BT.
- Rock PI 4B has AP6256 Wifi/BT, PoE.
- Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enable
  GPIO pin change compared to 4B, 4C

So move common nodes, properties into dtsi file and include
on respective variant dts files.

Use 4B dts into default rock-pi-4 defconfig until we find any
solution for dynamic detection of these variants.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

To fix below build error:
drivers/usb/host/built-in.o: In function `xhci_dwc3_remove':
drivers/usb/host/xhci-dwc3.c:174: undefined reference to `dwc3_shutdown_phy'
drivers/usb/host/built-in.o: In function `xhci_dwc3_probe':
drivers/usb/host/xhci-dwc3.c:130: undefined reference to `dwc3_setup_phy'
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>

Disable ram rockchip debug driver for roc-rk3399-pc
boards since we have verified ram in many instances
with respective U-Boot versions.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Add U-Boot SPI Flash support for the PINE64 Rock64 board
Signed-off-by: NJohannes Krottmayer <krjdev@gmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Adjust the ENV offset, size to fit into all images
on 16MB flash.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Enable DWC3 core, gadget for roc-rk3399-pc board.

This would help to use fastboot by default.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Enable config options to get HDMI output on RockPI-4 boards.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Enable USB gadget for rock-pi-4 boards.

This would help to use fastboot by default.

Note: Connect the Host USB cable (Port A or C) to rock-pi-4
Upper USB 3.0 port.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Enable PCI/NVME for M.2 Slot on RockPI-4 boards.

=> nvme info
Device 0: Vendor: 0x144d Rev: 2B2QEXM7 Prod: S4EUNG0MC10012Y
            Type: Hard Disk
            Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)

Cc: Tom Cubie <tom@radxa.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Enable USB3.0 Host support for RockPI-4 boards.

Note that the Upper USB3.0 port is marked as otg and
lower USB3.0 port marked as host, so this below log
capture when USB3.0 mass storage plug in at lower
USB 3.0 port.

Log:
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... cannot reset port 1!?
2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
  1  Hub (480 Mb/s, 0mA)
     u-boot EHCI Host Controller

  1  Hub (480 Mb/s, 0mA)
     u-boot EHCI Host Controller

  1  Hub (5 Gb/s, 0mA)
     U-Boot XHCI Host Controller

  1  Hub (5 Gb/s, 0mA)
  |  U-Boot XHCI Host Controller
  |
  +-2  Mass Storage (5 Gb/s, 224mA)
       SanDisk Dual Drive 040130e3ee554b7078843f4eb331646

Cc: Tom Cubie <tom@radxa.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Enable USB3.0 Host support for RockPro64 boards.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Also known as Odroid Go Advance but named Go2 internally by the
vendor it seems.
Signed-off-by: NHeiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC
driver can be used for SoC detection.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>

Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC
driver can be used for SoC detection.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>

Add a sandbox SOC driver, and some tests for the SOC uclass.
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>

This patch adds very basic minimal support for the Marvell Octeon 3
CN73xx based EBB7304 EVK. Please note that the basic Octeon port does
not support DDR3/4 initialization yet. To still use U-Boot on with this
port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot
to the prompt on this board.

Supported devices:
- UART
- reset
- CFI parallel NOR flash
Signed-off-by: NStefan Roese <sr@denx.de>

This converts the following to Kconfig:
   CONFIG_MXC_UART
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NPeng Fan <peng.fan@nxp.com>