In general, we want to load the DT at base+128MB, so that we ahve
sufficient room for the kernel and a larger device tree.  In the case of
OMAP3, use 64MB instead as we have a number of boards with 128MB DDR.
Signed-off-by: NTom Rini <trini@ti.com>

Adding support for reading cpsw 2nd mac address from efuse and pass it
to kernel via dtb which will be used in dual emac mode of cpsw.
Also adding mii command support to am335x common config.
Acked-by: NTom Rini <trini@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>

This patch add support for the Silica Pengwyn board [1]
The board is based on a TI AM3354 CPU [2]
All jumpers removed it will boot from the SDcard, the console is on
UART1 accessible via the FDTI -> USB. The on board NAND flash is
supported and can act as boot medium, depending on jumper settings.
USB Host, USB Device and Ethernet are also provided but untested.

[1]
http://www.silica.com/product/silica-pengwyn-board.html
[2]
http://www.ti.com/product/am3354Signed-off-by: NLothar Felten <lothar.felten@gmail.com>
[trini: Move CONFIG_BOARD_LATE_INIT into am335x_evm.h, drop unused
spi0_pin_mux from Pengwyn support]
Signed-off-by: NTom Rini <trini@ti.com>

The ELM hardware engine wihich is used for ECC error detections is not present
on OMAP3 SoC, so move the CONFIG_SPL_NAND_AM33XX_BCH from ti_armv7_common.h to
SoC configuration file.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>

Some am33xx boards may not use the RTC block for bootcount (as it may
not be wired up for the board) and use some other facility.  So add
another symbol for the bootcount driver for the IP block.
Acked-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NTom Rini <trini@ti.com>

As
http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast
states:
"Initialize devices only when they are needed within U-Boot"

enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is
enabled. Enable this in ti_am335x_common.h, so all boards in mainline
should work as before.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>

There is a board-specific portion for calling watchdog enable itself, in
main U-Boot.
Signed-off-by: NTom Rini <trini@ti.com>

Enable the bootcount driver for am335x in general.  We leave adding a
bootlimit and altbootcmd to the environment to the board ports.
Signed-off-by: NTom Rini <trini@ti.com>

Signed-off-by: NTom Rini <trini@ti.com>

While in here, drop CONFIG_BOOTP_DEFAULT as it is unused in the code.
Signed-off-by: NTom Rini <trini@ti.com>

We had been allowing the max size to be larger than actually allowed by
the ROM.  Expand the commentary here to explain why we set these
locations.
Signed-off-by: NTom Rini <trini@ti.com>

We create two new files, include/configs/ti_armv7_common.h for all of
the common IP blocks and related features / commands we share in
virtually all of our platforms.  We then create
include/configs/ti_am335x_common.h for everything common to the am335x
SoC leaving just the board specific parts to
include/configs/ti_am335x_common.h.
Signed-off-by: NTom Rini <trini@ti.com>