- 13 12月, 2013 9 次提交
-
-
由 Tom Rini 提交于
To make managing the environment easier, add DFUARGS to CONFIG_EXTRA_ENV_SETTINGS. Then we set DFUARGS down in the DFU part of the file, and include (or not) the NAND part, based on if NAND is set. Signed-off-by: NTom Rini <trini@ti.com>
-
由 Stefan Roese 提交于
Add SPL U-Boot support to replace x-loader on the Compulab cm_t35 board. Currently only the 256MiB SDRAM board versions are supported. Tested by booting via MMC and NAND. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
-
由 Stefan Roese 提交于
The Head acoustics (HA) baseboard used the Technexion TAO3530 SOM and has only some minor differences to the Technexion Thunder baseboard. This patch adds support for this HA baseboard / TAO3530 as the "omap3_ha" build target. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Tapani Utriainen <tapani@technexion.com> Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de> Cc: Tom Rini <trini@ti.com>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de> Cc: Tapani Utriainen <tapani@technexion.com> Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de> Cc: Tom Rini <trini@ti.com>
-
由 Stefan Roese 提交于
The memory size is autodetected and is passed to the Linux kernel either via ATAGs or device-tree (dtb). So there is no need to pass it via the bootargs. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Tapani Utriainen <tapani@technexion.com> Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de> Cc: Tom Rini <trini@ti.com>
-
由 Stefan Roese 提交于
Add SPL support for the Technexion TAO3530 SOM to replace x-loader. Tested with the Thunder baseboard. Currently this is only tested with the TAO3530 SOM revision (Ax/Bx). Tested by booting via MMC and NAND. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Tapani Utriainen <tapani@technexion.com> Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de> Cc: Tom Rini <trini@ti.com>
-
由 Tapani Utriainen 提交于
Add support for TechNexion TAO3530 SoM This patch has been posted quite a long time ago. I ported it to the latest mainline U-Boot version. With some additional cleanup and enhancements. Signed-off-by: NTapani Utriainen <tapani@technexion.com> CC: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: NStefan Roese <sr@denx.de> Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de> Cc: Tom Rini <trini@ti.com>
-
由 Lokesh Vutla 提交于
With the current scenario SPL size is being overlapped with the public stack and not allowing any OMAP4 device to boot. So the suggestion came up was to move the TEXT_BASE down to non-HS limit. Fixing the same and also moving the SRAM_SCRATCH_SPACE_ADDR up to the end of image downloadable area. Discussion on this can be seen here: https://www.mail-archive.com/u-boot@lists.denx.de/msg127147.html Tested on OMAP4460 PANDA. Reported-by: NChao Xu <caesarxuchao@gmail.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Tom Rini 提交于
Test on Beaglebone white over cpsw, usb ether and SD card (read and write), performance increased, crc32 of data matches. Signed-off-by: NTom Rini <trini@ti.com>
-
- 12 12月, 2013 2 次提交
-
-
由 Jeroen Hofstee 提交于
The standalone programs do not use the api calls, but rely directly on u-boot variable gd->jt for the jump table. Commit fe1378a9 - "ARM: use r9 for gd" changed the register holding the address of gd, but the assembly code in the standalone examples was not updated accordingly. This broke the programs on ARM relying on the jumptable in the v2013.10 release. This patch unbricks them by using the correct register. Cc: Michal Simek <monstr@monstr.eu> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: NJeroen Hofstee <jeroen@myspectrum.nl>
-
由 Albert ARIBAUD 提交于
Revert commit 0f5141e9 which causes boards starting in FLASH to try and write to a FLASH location. Signed-off-by: NAlbert ARIBAUD <albert.u.boot@aribaud.net>
-
- 11 12月, 2013 2 次提交
-
-
git://git.denx.de/u-boot-arm由 Tom Rini 提交于
Conflicts: board/samsung/trats2/trats2.c include/configs/exynos5250-dt.h Signed-off-by: NTom Rini <trini@ti.com>
-
由 Albert ARIBAUD 提交于
Conflicts: arch/arm/cpu/armv7/rmobile/Makefile doc/README.scrapyard Needed manual fix: arch/arm/cpu/armv7/omap-common/Makefile board/compulab/cm_t335/u-boot.lds
-
- 10 12月, 2013 11 次提交
-
-
-
-
-
由 Ian Campbell 提交于
Signed-off-by: NIan Campbell <ijc@hellion.org.uk> Cc: albert.u.boot@aribaud.net
-
由 Soren Brinkmann 提交于
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Mike Frysinger 提交于
We want to test SPI flash code in the sandbox, so enable the new drivers and the 'sf test' command. This command is used to validate the sandbox SPI / SPI flash implementation, so enable it. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Mike Frysinger 提交于
This adds a SPI flash driver which simulates SPI flash clients. Currently supports the bare min that U-Boot requires: you can probe, read, erase, and write. Should be easy to extend to make it behave more exactly like a real SPI flash, but this is good enough to merge now. sjg@chromium.org added a README and tidied up code a little. Added a required map_sysmem() for sandbox. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Mike Frysinger 提交于
This adds a SPI framework for people to hook up simulated SPI clients. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This was obtained from Linux 3.12 commit 5e01dc7b26. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This allows us to put the SPI flash chip inside the SPI interface node, with U-Boot finding the correct bus and chip select automatically. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
The new name is longer but more clearly related to sandbox. This is in a separate patch within the same series since some comments on the SPI series rely on it. Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NHung-ying Tyan <tyanh@chromium.org>
-
- 09 12月, 2013 7 次提交
-
-
由 Mateusz Kulikowski 提交于
Add support for USB-A9263 board manufactured by Calao Systems (http://www.calao-systems.com/). Code is based on old U-Boot sources (2010.09) released by Calao. Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Heiko Schocher 提交于
enable support for the siemens AT91SAM9G20 based board corvus. Signed-off-by: NBoris Schmidt <boris.schmidt@siemens.com> Reviewed-by: NHeiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Bo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Heiko Schocher 提交于
enable support for the siemens AT91SAM9G20 based boards taurus and axm. Signed-off-by: NRoger Meier <r.meier@siemens.com> Reviewed-by: NHeiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Bo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Andreas Bießmann 提交于
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Andreas Bießmann 提交于
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com> Acked-by: Jens Scharsig (BuS Elektronik)<esw@bus-elektronik.de> Tested-by: Jens Scharsig (BuS Elektronik)<esw@bus-elektronik.de> Acked-by: NScott Wood <scottwood@freescale.com>
-
由 Andreas Bießmann 提交于
In order to get the very same value for legacy pin definitions and new gpio definitions set the legacy PIN_BASE to 0. Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Andreas Bießmann 提交于
This patch define new names for GPIO pins on at91 devices. Follow up patches will convert the whole infrastructure to use these new definitions. Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com> Tested-by: NBo Shen <voice.shen@atmel.com>
-
- 08 12月, 2013 4 次提交
-
-
由 Kuo-Jung Su 提交于
Faraday FTSDC021 is a controller which is compliant with SDHCI v3.0, SDIO v2.0 and MMC v4.3. However this driver is only verified with SD memory cards. Signed-off-by: NKuo-Jung Su <dantesu@faraday-tech.com> Acked-by: NPantelis Antoniou <panto@antoniou-consulting.com> CC: Andy Fleming <afleming@gmail.com>
-
由 Priyanka Jain 提交于
Existing eSDHC SPL framework assumes booting from sd-image with boot_format header which contains final u-boot Image offset and size. No such header is present in case of corenet devices like T1040 as corenet deivces use PBI-RCW based intialization. So, for corenet deives, SPL bootloader use values provided at compilation time. These values can be defined in board specific config file. Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com> Acked-by: NPantelis Antoniou <panto@antoniou-consulting.com>
-
由 Alexey Brodkin 提交于
If platform provides "host->fifoth_val" it will be used for initialization of DWMCI_FIFOTH register. Otherwise default value will be used. This implementation allows: * escape unclear and recursive calculations that are currently in use * use whatever custom value for DWMCI_FIFOTH initialization if any particular SoC requires it Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com> Cc: Mischa Jonker <mjonker@synopsys.com> Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Amar <amarendra.xt@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Simon Glass <sjg@chromium.org> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Andy Fleming <afleming@freescale.com> Acked-by: NJaehoon Chung <jh80.chung@samsung.com> Acked-by: NPantelis Antoniou <panto@antoniou-consulting.com>
-
由 Jaehoon Chung 提交于
dw-mmc.c is the general driver file. So, remove the exynos specific code at dw-mmc.c. Instead, exynos specific cod can be move into exynos-dw_mmc.c. Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com> Acked-by: NAlexey Brodkin <abrodkin@synopsys.com> Acked-by: NPantelis Antoniou <panto@antoniou-consulting.com> Acked-by: NMinkyu Kang <mk7.kang@samsung.com>
-
- 07 12月, 2013 2 次提交
-
-
由 Albert ARIBAUD 提交于
Current LDS files /DISCARD/ a lot of sections when linking ELF files, causing diagnostic tools such as readelf or objdump to produce partial output. Keep all section at link stage, filter only at objcopy time so that .bin remains minimal. Signed-off-by: NAlbert ARIBAUD <albert.u.boot@aribaud.net> Reviewed-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
-
由 Masahiro Yamada 提交于
The lower 5 bit of MVBAR is UNK/SBZP. So, Monitor Vector Base Address must be 32-byte aligned. On the other hand, the secure monitor handler does not need 32-byte alignment. This commit moves ".algin 5" directive to the correct place. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Cc: Andre Przywara <andre.przywara@linaro.org> Acked-by: NAndre Przywara <andre.przywara@linaro.org>
-
- 06 12月, 2013 3 次提交
-
-
由 Albert ARIBAUD 提交于
-
由 Albert ARIBAUD 提交于
-
-