- 20 8月, 2013 18 次提交
-
-
由 Chunhe Lan 提交于
When the code detected that the bus is hung (e.g. SDA stuck low), send 9 pulses on SCL to try to fixup the bus. Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: NChunhe Lan <Chunhe.Lan@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Heiko Schocher <hs@denx.de>
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@ti.com>
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de> [trini Don't remove some copyrights by accident] Signed-off-by: NTom Rini <trini@ti.com>
-
由 Wolfgang Denk 提交于
The file header indicated that this file was GPL-2.0+, but actually the code was derived from (Marvell based) Linux source code which is only GPL-2.0. Fix this. Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Acked-by: NStefan Roese <sr@denx.de>
-
由 Wolfgang Denk 提交于
This commit adapts the files that were derived from PIBS (PowerPC Initialization and Boot Software) codeto using SPDX License Identifiers. So far, SPDX has not assigned an official License ID for the PIBS license yet, so this should be considered preliminary. Note that the following files contained incorrect license information: arch/powerpc/cpu/ppc4xx/4xx_uart.c arch/powerpc/cpu/ppc4xx/start.S arch/powerpc/include/asm/ppc440.h These files included, in addition to the GPL-2.0 / ibm-pibs dual license as inherited from PIBS, a GPL-2.0+ license header which was obviously incorrect. This has been removed. Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: NWolfgang Denk <wd@denx.de> Conflicts: Licenses/README Acked-by: NStefan Roese <sr@denx.de>
-
由 Wolfgang Denk 提交于
Unlike the other patches in this series so far, this commit fixes a ambiguity in the license terms for some OMAP files: the code was originally derived from the Linux kernel sources, where it was clearly marked as GPL-2.0 (i. e. without the "or later" part), but the U-Boot version had a GPL-2.0+ file header added, apparently without permission / relicensing from the original authors of the code. Insert a GPL-2.0 SPDX-License-Identifier to fix this. Signed-off-by: NWolfgang Denk <wd@denx.de> cc: Tom Rix <Tom.Rix@windriver.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: NTom Rini <trini@ti.com>
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Kuo-Jung Su 提交于
1. Reformat tx/rx descriptor as an uniform struct. 2. Replace uint32_t[2] with uint64_t for descriptor control. Signed-off-by: NKuo-Jung Su <dantesu@faraday-tech.com> CC: Joe Hershberger <joe.hershberger@gmail.com>
-
由 Kuo-Jung Su 提交于
Signed-off-by: NKuo-Jung Su <dantesu@faraday-tech.com> CC: Joe Hershberger <joe.hershberger@gmail.com>
-
由 Kuo-Jung Su 提交于
Signed-off-by: NKuo-Jung Su <dantesu@faraday-tech.com> CC: Joe Hershberger <joe.hershberger@gmail.com>
-
由 Jeroen Hofstee 提交于
The __* keywords are reserved. On FreeBSD __unused evaluates to the attribute unused, causing a compilation failure. Just use unused instead. Signed-off-by: NJeroen Hofstee <jeroen@myspectrum.nl> cc: joe.hershberger@gmail.com
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@ti.com>
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@ti.com>
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@ti.com>
-
由 Bhupesh Sharma 提交于
This patch adds support for Realtek PHY modules RTL8211DN and RTL8211E (variants: RTL8211E-VB-CG, RTL8211E-VL-CG, RTL8211EG-VB-CG), which can be found on Freescale's T1040RDB boards. To make the driver more generic across 8211 family, a generic name 8211x is added for macros and function names. Signed-off-by: NBhupesh Sharma <bhupesh.sharma@freescale.com> Acked-by: NYork Sun <yorksun@freescale.com>
-
由 Stefan Roese 提交于
This patch adds support for the SMSC9500 with product id 0x9900 which is equipped in the "EXSYS USB 2.0" etherner USB adapter. Tested on omap3_beagle. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Axel Lin 提交于
Use ARRAY_SIZE instead of having similar implementation in each drivers. The NUMELEMS defined in drivers/net/npe/include/IxOsalTypes.h is not used at all, so this patch removes it instead of converting it to use ARRAY_SIZE. Signed-off-by: NAxel Lin <axel.lin@ingics.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Marek Vasut <marex@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: TsiChungLiew <Tsi-Chung.Liew@freescale.com> Cc: Wolfgang Denk <wd@denx.de> Cc: York Sun <yorksun@freescale.com>
-
由 Fabio Estevam 提交于
LAN8710/8720 are 10/100 Mbps PHYs, so fix the '.features' field. Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
- 19 8月, 2013 6 次提交
-
-
由 Axel Lin 提交于
Use default_serial_puts() instead of its own implementation. Signed-off-by: NAxel Lin <axel.lin@ingics.com> Acked-by: NMarek Vasut <marex@denx.de> Acked-by: NMichal Simek <monstr@monstr.eu>
-
由 Dirk Eibach 提交于
Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Dirk Eibach 提交于
Up to this point some PHY initialization was done from the FPGA and some from u-boot. From now all initialization is done from u-boot. To keep this maintainable a PHY setup machine was implemented that can execute commands from initialization arrays. Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Dirk Eibach 提交于
Add a new iocon flavor with a second communiction port per channel. Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Dirk Eibach 提交于
Add a new iocon flavor with fiber instead of copper connectivity. Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: NStefan Roese <sr@denx.de>
-
git://88.191.163.10/u-boot-arm由 Tom Rini 提交于
Fixup an easy conflict over adding the clk_get prototype and USB_OTG defines for am33xx having moved. Conflicts: arch/arm/include/asm/arch-am33xx/hardware.h Signed-off-by: NTom Rini <trini@ti.com>
-
- 18 8月, 2013 1 次提交
-
-
由 Albert ARIBAUD 提交于
-
- 17 8月, 2013 7 次提交
-
-
由 Axel Lin 提交于
Signed-off-by: NAxel Lin <axel.lin@ingics.com> Reviewed-by: NThierry Reding <thierry.reding@gmail.com> Acked-by: NMarek Vasut <marex@denx.de>
-
由 York Sun 提交于
Commit 669dfc2e adds libfdt_env.h to HOSTCPPFLAGS. It causes stdio.h to be included before _GNU_SOURCE is defined in C files. On some old hosts some prototypes are protected by #ifdef __USE_GNU, which is set when _GNU_SOURCE is defined. Signed-off-by: NYork Sun <yorksun@freescale.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
The timestamp is shown in fit_print_contents() but for some reason not in fit_image_print(). This seems to be an oversight, since it is the latter which is used by bootm. Add timestamp printing in this case. (There is code duplication in these two function, for looking at in a future patch). Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Paul B. Henson 提交于
This function is only defined if CONFIG_SILENT_CONSOLE is set and CONFIG_SILENT_U_BOOT_ONLY is not set, the call to it should be based on the same conditions. Signed-off-by: NPaul B. Henson <henson@acm.org> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
At present the console for linux is silent if the U-Boot console is silent, unless CONFIG_SILENT_U_BOOT_ONLY is set. I wonder if a better way would be to have an environment variable to control this? Then we can control the verbosity from scripts, and set the variable to 'no' for those boards that want Linux to boot with console output. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Taras Kondratiuk 提交于
If image name is longer than 32 bytes, then it will be truncated. This will remove '\0' at the end of the line, so printf will go out of string limit. Signed-off-by: NTaras Kondratiuk <taras@ti.com> Reviewed-by: NTom Rini <trini@ti.com>
-
由 Angus Ainslie 提交于
This is a trivial patch that just enables xmodem downloads using the existing ymodem framework. Signed-off-by: NAngus Ainslie <angus@akkea.ca>
-
- 16 8月, 2013 8 次提交
-
-
由 TENART Antoine 提交于
Signed-off-by: NAntoine Tenart <atenart@adeneo-embedded.com> [trini: Change to SPDX, fix a few compiler warnings, adapt to CONFIG_OMAP_COMMON] Signed-off-by: NTom Rini <trini@ti.com>
-
由 TENART Antoine 提交于
Signed-off-by: NAntoine Tenart <atenart@adeneo-embedded.com> [trini: Fix warnings about vtp things in emif4.c, adapt AM43XX] Signed-off-by: NTom Rini <trini@ti.com>
-
由 TENART Antoine 提交于
Rename some CONFIG_TI814X to a more generic CONFIG_TI81XX Signed-off-by: NAntoine Tenart <atenart@adeneo-embedded.com> [trini: Adapt for CONFIG_OMAP_COMMON changes, AM43XX] Signed-off-by: NTom Rini <trini@ti.com>
-
由 Heiko Schocher 提交于
add the am1808 based ipam390 board from Barix. - 128MByte, DDR2, synchronous RAM 16bit databus to SDRAM interface - 128MByte, NAND Flash, 8bit databus to the NANDFlash Interface - Ethernet PHY Micrel KSZ8051R via RMII - Console on UART 0 - booting fron nand flash - spl falcon bootmode Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
-
由 Heiko Schocher 提交于
in arch_cpu_init() uart2 is fix enabled, without reference the setting from CONFIG_SYS_NS16550_COM1. Use the setting from CONFIG_SYS_NS16550_COM1 for enabling the console. Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Tom Rini <tom.rini@gmail.com> Cc: Christian Riesch <christian.riesch@omicron.at>
-
由 Heiko Schocher 提交于
In case CONFIG_BOOTSTAGE is not defined, call from bootstage_mark_name() show_boot_progress(), so get more BOOTSTAGE_ID* ids in show_boot_progress() if CONFIG_BOOTSTAGE is not defined. Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
-
由 Tom Rini 提交于
Add the generic "poke a GPIO" command, with the GPIO related defines. Acked-by: NDan Murphy <dmurphy@ti.com> Signed-off-by: NTom Rini <trini@ti.com>
-