enable support for the siemens AT91SAM9G20 based board corvus.
Signed-off-by: NBoris Schmidt <boris.schmidt@siemens.com>
Reviewed-by: NHeiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

enable support for the siemens AT91SAM9G20 based boards taurus
and axm.
Signed-off-by: NRoger Meier <r.meier@siemens.com>
Reviewed-by: NHeiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

Phytec sells revision or version 3 of pcm051. It is labeled 1358.3 on
the board. The difference for u-boot is that is has other DDR3 RAM on it:
1 x MT41K256M16HA125E instead of 2 x MT41J256M8HX15E on revisions 1 and
2. Both configurations are 512 MiB.
Configure your u-boot build with pcm051_rev3 for the new RAM and
pcm051_rev1 for the old RAM configuration. Board revision 2 has to use
pcm051_rev1 also.
Signed-off-by: NLars Poeschel <poeschel@lemonage.de>

Add cm_t335 board directory, config file. Enable build.
Signed-off-by: NIlya Ledvich <ilya@compulab.co.il>
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
[trini: Adapt Makefile]
Signed-off-by: NTom Rini <trini@ti.com>

The koelsch board has R8A7791, 2GB DDR3-SDRAM, USB,
Quad SPI, Ethernet, and more.

This patch supports the following functions:
 - DDR3-SDRAM
 - SCIF
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NHisashi Nakamura <hisashi.nakamura.ak@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>

The lager board has R8A7790, 4GB DDR3-SDRAM, USB, Ethernet, and more.

This patch supports the following functions:
 - DDR3-SDRAM
 - SCIF
Signed-off-by: NKouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: NHisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: NRyo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>

Signed-off-by: NTom Rini <trini@ti.com>

Commit f6d1f6e4 broke selection of UARTs
other than UART0 for am335x_evm configurations by setting CONS_INDEX to
1 for all configurations.  Revert the CONS_INDEX changes.
Signed-off-by: NAndrew Bradford <andrew@bradfordembedded.com>

Update my email address as ti814x_evm maintainer to save
people some frustrating bounces and non-response.
Signed-off-by: NMatt Porter <matt.porter@linaro.org>

Remove 'HEAD' line which is most likely left there while rebasing. It was
introduced in commit 877bfe37.
Signed-off-by: NLuka Perkov <luka@openwrt.org>

Commit 93e14596 "Coding Style cleanup: replace leading SPACEs by TABs"
added trailing whitespace to a single line of boards.cfg. I presume this
was unintentional, and it causes the file to change after running it
through the reformat.py script. Remove the offending character.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

UART booting is supported on this SoC, but via UART3 rather than UART1.
Because of this we must change the board to use UART3 for all console
access (only one UART is exposed on this board and a slight HW mod is
required to switch UARTs).
Signed-off-by: NMinal Shah <minal.shah@ti.com>
[trini: Make apply to mainline, reword commit]
Signed-off-by: NTom Rini <trini@ti.com>

The 'flashcard' u-boot configuration has a readonly environment and boots a
bare kernel/initrd to program the device from an clean environment.
Signed-off-by: NAndreas Bießmann <andreas.biessmann@corscience.de>

There seems to be a naming convention for the configuration
files for boards using the same SoC family. This makes
easier to do changes that affect different boards based
on the same SoC.

Since the IGEPv2 board and the IGEP COM Module use a TI
OMAP35xx/DM37xx processor, is better to rename its board
config to use this naming scheme.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>

There seems to be a naming convention for the configuration
files for boards using the same SoC family. This makes
easier to do changes that affect different boards based
on the same SoC.

Since the IGEP COM AQUILA use a TI AM335x processor is better
to rename its board config to use this naming scheme.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>

This patch introduces the support for Keymile's kmp204x reference
design. This design is based on Freescale's P2040/P2041 SoC.

The peripherals used by this design are:
- DDR3 RAM with SPD support
- SPI NOR Flash as boot medium
- NAND Flash
- 2 PCIe busses (hosts 1 and 3)
- 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5)
- 3 Local Bus windows, with one dedicated to the QRIO reset/power mgmt
  FPGA
- 2 HW I2C busses
- last but not least, the mandatory serial port

The board/keymile/kmp204x code is mostly based on Freescale's P2041rdb
support and was changed according to our design (that means essentially
removing what is not present on the designs and a few adaptations).

There is currently only one prototype board that is based on this design
and this patch also introduces it. The board is called kmlion1.
Signed-off-by: NStefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>

kmp204x: update the ENV #define

The comments had to be refined as well as the total size
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix ddr.c]
Acked-by: NYork Sun <yorksun@freescale.com>

This board supports FEC Ethernet, SPI NOR and NAND flash.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Christoph Baumann <c.baumann@ppc-ag.de>

Add basic support for mx6q udoo board.

For further information about Udoo board:
http://www.udoo.org/

Tested booting a mainline device tree kernel and a Yocto rootfs from mmc.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

Remove Prodrive pdnb3 board (including the scpu variant) support
from mainline. As its unmaintained and not needed any more for
quite some time.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Martijn de Gouw <martijn.de.gouw@prodrive.nl>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>

- Rename old P1010RDB board as P1010RDB-PA.
- Add support for new P1010RDB-PB board.
- Some optimization.

For more details, see board/freescale/p1010rdb/README.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix conflicts in boards.cfg]
Acked-by: NYork Sun <yorksun@freescale.com>

T1040QDS is a high-performance computing evaluation, development and
test platform supporting the T1040 QorIQ Power Architecture™ processor.

 T1040QDS board Overview
 -----------------------
 - Four e5500 cores, each with a private 256 KB L2 cache
 - 256 KB shared L3 CoreNet platform cache (CPC)
 - Interconnect CoreNet platform
 - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
   support
 - Data Path Acceleration Architecture (DPAA) incorporating acceleration
 for the following functions:
    -  Packet parsing, classification, and distribution
    -  Queue management for scheduling, packet sequencing, and congestion
    	management
    -  Cryptography Acceleration
    - RegEx Pattern Matching Acceleration
    - IEEE Std 1588 support
    - Hardware buffer management for buffer allocation and deallocation
 - Ethernet interfaces
    - Integrated 8-port Gigabit Ethernet switch
    - Four 1 Gbps Ethernet controllers
 - SERDES Connections, 8 lanes supporting:
      — PCI Express: supporting Gen 1 and Gen 2;
      — SGMII
      — QSGMII
      — SATA 2.0
      — Aurora debug with dedicated connectors
 - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
   Interleaving
 -IFC/Local Bus
     - NAND flash: 8-bit, async, up to 2GB.
     - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
     - GASIC: Simple (minimal) target within Qixis FPGA
     - PromJET rapid memory download support
 - Ethernet
     - Two on-board RGMII 10/100/1G ethernet ports.
     - PHY #0 remains powered up during deep-sleep
 - QIXIS System Logic FPGA
 - Clocks
     - System and DDR clock (SYSCLK, “DDRCLK”)
     - SERDES clocks
 - Power Supplies
 - Video
     - DIU supports video at up to 1280x1024x32bpp
 - USB
     - Supports two USB 2.0 ports with integrated PHYs
     — Two type A ports with 5V@1.5A per port.
     — Second port can be converted to OTG mini-AB
 - SDHC
     - SDHC port connects directly to an adapter card slot, featuring:
     - Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC
     — Supporting eMMC memory devices
 - SPI
    -  On-board support of 3 different devices and sizes
 - Other IO
    - Two Serial ports
    - ProfiBus port
    - Four I2C ports
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: fix conflict in boards.cfg]
Acked-by-by: NYork Sun <yorksun@freescale.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>
[trini: Drop changes for PEP 4 following python tools]
Signed-off-by: NTom Rini <trini@ti.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>

omap1510inn is orphan and has been for years now.
Reove it and, as it was the only arm925t target,
also remove arm925t support.
Update doc/README.scrapyard accordingly.
Signed-off-by: NAlbert ARIBAUD <albert.u.boot@aribaud.net>

This patch add support for a new Samsung board Trats2.
Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

Add the missing bang (!) to execute external command, otherwise it does not
work.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>

Put all informations about targets, including state (active or
orphan) and maintainers, in boards.cfg; remove MAINTAINERS;
adjust the build system accordingly.
Signed-off-by: NAlbert ARIBAUD <albert.u.boot@aribaud.net>

Signed-off-by: NPhilippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: NEric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: NNicolas Colombain <nicolas.colombain@armadeus.com>

Add STMP3780-based Sansa Fuze+ board. This board is a small PMP
device sporting a CPU which was later rebranded to i.MX233 .
Currently supported is USB gadget mode and MMC .
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>

Add STMP3780-based XFi3 board. This board is a small PMP device
sporting a CPU which was later rebranded to i.MX233 . Currently
supported is USB gadget mode and both external SD and internal
Phison SD-NAND bridge .
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>

These boards were not sortes in the boards.cfg, fix this.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>

Arndale board is based on samsung's exynos5250 soc.
Signed-off-by: NInderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: NChander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

add support for the am335x based boards from siemens:

dxr2:
  - DDR3 128MiB
  - NAND 256MiB
  - Ethernet with external Switch SMSC LAN9303
  - no PMIC
  - internal Watchdog
  - DFU support

pxm2:
  - DDR2 512 MiB
  - NAND 1024 MiB
  - PMIC
  - PHY atheros ar803x
  - USB Host
  - internal Watchdog
  - DFU support

rut:
  - DDR3 256 MiB
  - NAND 256 MiB
  - PMIC
  - PHY natsemi dp83630
  - external Watchdog
  - DFU support
Signed-off-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NRoger Meier <r.meier@siemens.com>
Signed-off-by: NSamuel Egli <samuel.egli@siemens.com>
Cc: Pascal Bach <pascal.bach@siemens.com>
Cc: Tom Rini <trini@ti.com>

The target uses AUART 3 instead of the DUART for console output.
Signed-off-by: NAndreas Wass <andreas.wass@dalelven.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>

This board and especially the CPU (PPC405CR) is EOL.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NAntoine Tenart <atenart@adeneo-embedded.com>
[trini: Change to SPDX, fix a few compiler warnings, adapt to
CONFIG_OMAP_COMMON]
Signed-off-by: NTom Rini <trini@ti.com>

add the am1808 based ipam390 board from Barix.

- 128MByte, DDR2, synchronous RAM 16bit databus to SDRAM
  interface
- 128MByte, NAND Flash, 8bit databus to the NANDFlash
  Interface
- Ethernet PHY Micrel KSZ8051R via RMII
- Console on UART 0
- booting fron nand flash
- spl falcon bootmode
Signed-off-by: NHeiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>

Add config file
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

C29XPCIE board is a series of Freescale PCIe add-in cards to perform
as public key crypto accelerator or secure key management module. It
includes C293PCIE board, C293PCIE board and C291PCIE board.

 - 512KB platform SRAM in addition to 512K L2 Cache/SRAM
 - 512MB soldered DDR3 32bit memory
 - CPLD System Logic
 - 64MB x16 NOR flash and 4GB x8 NAND flash
 - 16MB SPI flash
Signed-off-by: NMingkai Hu <Mingkai.Hu@freescale.com>
Singed-off-by: NPo Liu <Po.Liu@freescale.com>
[yorksun: Fixup include/configs/C29XPCIE.h]
Signed-off-by: NYork Sun <yorksun@freescale.com>

Add new board p1020RDB-PD. P1020RDB-PD board was update from P1020RDB.
DDR changed from DDR2 1G to DDR3 2G.
NAND: 128 MiB
Flash: 64 MiB

Also change P1020RDB to P1020RDB-PC to distinguish from P1020RDB board.
Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: NHaijun Zhang <Haijun.Zhang@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Acked-by: NYork Sun <yorksun@freescale.com>