Configure the number of bits used to address the banks inside the SDRAM
device.  The default register value of 0 means 2 bits to address 4 banks.
Higher capacity devices like a 2GB DIMM require 3 bits to address 8 banks.
Signed-off-by: NBecky Bruce <bgill@freescale.com>

Just use the standard defines in asm/cache.h.
Signed-off-by: NJon Loeliger <jdl@freescale.com>

Assumes the presence of the aliases node in the DTS to
locate the pci and serial nodes for fixups.

Use consistent fdtaddr and fdtfile in environment variables.
Signed-off-by: NJon Loeliger <jdl@freescale.com>

Turn off DEBUG.
Signed-off-by: NJon Loeliger <jdl@freescale.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>

didnt realize how out of shape easylogo actually was until i tried using it.
this patch does byte swapping as need be on the input tga header since the tga
is in little endian but the host could just as well be big endian.  i didnt
bother using bswap macros or such stuff from system headers as nothing in
POSIX dictates byte swapping functionality.
Signed-Off-By: NMike Frysinger <vapier@gentoo.org>

- make the Makefile not suck
- include proper headers for prototypes
- fix obvious broken handling of strchr() when handling '.' in filenames
Signed-Off-By: NMike Frysinger <vapier@gentoo.org>

This patch allows u-boot to build without error in a cygwin
environment.  Cygwin does not define __u64 in it's
include/asm/types.h file.  The -idirafter flag in the u-boot
build causes the inclusion of the cygwin types.h file as opposed
to u-bot/include/asm/types.h file which does define __u64.
Subsequently, sha1.c compile fails due to unknown symbol.
Signed-off-by: NBrian Miller <raptorbrino@netscape.net>

The existing code can show information about a gzip compressed BMP
image, but can't actually display it.

Therefore, move the decompression code out of bmp_info() and use it in
bmp_display() as well in order to display a compressed BMP image.

Also, clean things up a bit and fix a memory leak while we're at it.

[hskinnemoen@atmel.com: a bit of refactoring]
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>

This patch fixes several issues at least on a MPC885 based system with two
FEC interfaces used in MII mode.

1. PHY discovery should first read PHY_PHYIDR2 register and only then
   PHY_PHYIDR1 like cpu/mpc8xx/fec.c::mii_discover_phy() does it,
   otherwise the values read are wrong. Also notice, that PHY discovery
   cannot work on MPC88x / MPC87x in setups with both FECs active at all
   in its present form, because for both interfaces the registers from FEC
   1 are used to communicate over MII.

2. Remove code duplication for resetting the FEC by isolating it into a
   separate function.

3. Initialize MII on FEC 1 when communicating over FEC 2 in fec_init().

4. Optimize mii_init() to only reset the FEC 1 controller once.

5. Fix a typo in mii_init() using index i instead of j thus potentially
   leading to unpredictable results.
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>

It is unclear on what platforms this driver has been tested, since
noone up to now defines CONFIG_RTL8169 in the board configuration
header. Now it has been fixed for a big-endian mpc8241 based
linkstation platform. This patch presents the necessary endianness
conversion fixes.
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>

This patch removes the unnecessary bit swapping when
booting .bit files with the 'fpga loadb' command.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

This patch adds a post configuration callback for Spartan2/3 FPGAs.
pre and post configuration callback are now optional and
not called when the function pointer is set to NULL.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

This patch removes the FPGA subsystem configuration through
the CONFIG_FPGA bitmask configuration option.

See README for the new options:

	CONFIG_FPGA,
	CONFIG_FPGA_<vendor>,
	CONFIG_FPGA_<family>
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

With this patch it is possible to reimplement default_serial_console()
in board specific code. This will be done in the upcomming PMC440
U-Boot port. This also allows the lwmon board maintainer to
remove the '#if !defined(CONFIG_LWMON) ...' from common/serial.c.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

This patch adds a 'cu' like serial terminal command to u-boot
using which you can access other serial ports from the system console.

OpenMoko uses this in their Neo1973 phones to get access to the GSM
Modem and GPS chip from the bootloader.
Signed-off-by: NHarald Welte <laforge@openmoko.org>

that used to exist with the legacy NAND code
Signed-off-by: NHarald Welte <laforge@openmoko.org>

Signed-off-by: NHarald Welte <laforge@openmoko.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Add until the new phylib will be arrived
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

based on Linux source tree's .gitignore files
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>

On LWMON5 we now use d-cache as init-ram and stack. The SPR POST test uses
self modifying code and this doesn't work with stack in d-cache, since
I can't move the code from d-cache to i-cache. We move the SPR test to
be executed a little later, after relocation. Then stack is located in
SDRAM and this self-modifying code is no problem anymore.
Signed-off-by: NStefan Roese <sr@denx.de>

This patch configures the LWMON5 port to use d-cache as init-ram and
the unused GPT0_COMP6 as POST WORD storage.
Signed-off-by: NStefan Roese <sr@denx.de>

The privious 4xx POST implementation only supported storing the POST
WORD in OCM. Since we need to reserve the OCM on LWMON5 for the logbuffer
we need to store the POST WORD in some other non volatile location.
This patch adds CFG_POST_ALT_WORD_ADDR to specify an address for such
a location.
Signed-off-by: NStefan Roese <sr@denx.de>

This patch adds support for locking the init-ram/stack in d-cache,
so that other regions may use d-cache as well

Note, that this current implementation locks exactly 4k of d-cache,
so please make sure that you don't define a bigger init-ram area. Take
a look at the lwmon5 440EPx implementation as a reference.
Signed-off-by: NStefan Roese <sr@denx.de>

ext2fs_read_file() had the function arguments swapped.

Pointed out by Mike Montour, 19 Dec 2007 22:34:25 -0800
Signed-off-by: NWolfgang Denk <wd@denx.de>

The MPC5200 OHCI controller operates in big endian, so
CFG_OHCI_BE_CONTROLLER must be defined for it to work properly.
Signed-off-by: NMarkus Klotzbuecher <mk@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>

This patch updates the fw_printenv/fw_setenv userspace tool to include
the correct MTD header in order to compile against current kernel
headers. Backward compatibility is preserved by introducing an option
MTD_VERSION which can be set to "old" for compilation using the old MTD
headers. Along with this a number of warnings are fixed.
Signed-off-by: NMarkus Klotzbuecher <mk@denx.de>