- 12 12月, 2010 1 次提交
-
-
由 Dirk Behme 提交于
CC: Ruslan N. Araslanov <byaaka@yandex.ru> Signed-off-by: NRuslan Araslanov <ruslan.araslanov@vitecmm.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 20 11月, 2010 1 次提交
-
-
由 Grazvydas Ignotas 提交于
Most OMAP3 boards have various flash related macros in their configs that are either not referenced anywhere in the code or are used by drivers that are not enabled. Remove them. Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com> Acked-by: NSteve Sakoman <steve@sakoman.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 05 11月, 2010 2 次提交
-
-
由 Steve Sakoman 提交于
This patch fixes the issue by defining and using CONFIG_SYS_INIT_RAM_SIZE and CONFIG_SYS_INIT_RAM_ADDR. Based on an email discussion with Wolfgang Denk and Heiko Schocher. Signed-off-by: NSteve Sakoman <steve.sakoman@linaro.org> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Koen Kooi 提交于
Beagle expansion boards contain an i2c eeprom to identify themselves. This patch adds code to read and parse the eeprom contents. It prints the expansion board name and revision and modifies environment variables as appropriate. This patch is based on the Overo expansion board code. Signed-off-by: NKoen Kooi <k-kooi@ti.com> Signed-off-by: NSteve Sakoman <steve.sakoman@linaro.org> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 27 10月, 2010 1 次提交
-
-
由 Wolfgang Denk 提交于
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not being able to use "sizeof(struct global_data)" in assembler files. Recent experience has shown that manual synchronization is not reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into GENERATED_GBL_DATA_SIZE which gets automatically generated by the asm-offsets tool. In the result, all definitions of this value can be deleted from the board config files. We have to make sure that all files that reference such data include the new <asm-offsets.h> file. No other changes have been done yet, but it is obvious that similar changes / simplifications can be done for other, related macro definitions as well. Signed-off-by: NWolfgang Denk <wd@denx.de> Acked-by: NKumar Gala <galak@kernel.crashing.org>
-
- 19 10月, 2010 1 次提交
-
-
由 John Rigby 提交于
For testing ARM device tree support Signed-off-by: NJohn Rigby <john.rigby@linaro.org> Acked-by: NWolfgang Denk <wd@denx.de>
-
- 18 10月, 2010 2 次提交
-
-
由 Steve Sakoman 提交于
This patch switches from the legacy mmc driver to the new generic mmc driver Signed-off-by: NSteve Sakoman <steve@sakoman.com>
-
由 Steve Sakoman 提交于
TI hasn't reserved a USB Product ID for gadgets, so use the default vendor and product ID to avoid confusion. Signed-off-by: NSteve Sakoman <steve@sakoman.com>
-
- 13 10月, 2010 2 次提交
-
-
由 Ben Gardiner 提交于
There were some #undef's of CONFIG_SYS_ARM_WITHOUT_RELOC added to a few board configs as part of the arm relocation series; but these are not needed now as we do not #undef what is not #defined in the first place. Signed-off-by: NBen Gardiner <bengardiner@nanometrics.ca> CC: Heiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
- 20 9月, 2010 2 次提交
-
-
由 Heiko Schocher 提交于
Change the implementation for ARM V7 to relocate the code to an arbitrary address in RAM. Adapt the Beagle board (Cortex A8) to test the changes. Portions of this work were supported by funding from the CE Linux Forum. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
Add data cache support for ARM V7 systems. Used cache flush functions from linux:arch/arm/mm/cache-v7.S developed from Catalin Marinas. Enable "cache" command on Beagle board and test performance. Test 1: Loading 127 MB of data from NAND flash into RAM: Instr. Cache off on on Data Cache off off on -------------------------------------------------- Beagle (Cortex A8) 116s 106s 30.3s = x 3.8 Test 2: uncompressing a gzipped image from RAM to RAM (size compressed: 6.5 MiB, uncompressed: 35 MiB): Instr. Cache off on on Data Cache off off on -------------------------------------------------- Beagle (Cortex A8) 1.84s 1.64s 0.12s = x 15.3 Portions of this work were supported by funding from the CE Linux Forum. Signed-off-by: NHeiko Schocher <hs@denx.de> Reviewed-by: Ben Gardiner<bengardiner@nanometrics.ca>
-
- 09 9月, 2010 2 次提交
-
-
由 Steve Sakoman 提交于
Future versions of these boards have options for POP memory with no NAND. This option prevents display of error messages when no NAND is detected. Signed-off-by: NSteve Sakoman <steve@sakoman.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Steve Sakoman 提交于
Allows one to set the processor clock rate via "setenv mpurate 720" for example Default is set to a "safe" 500 Mhz. Signed-off-by: NSteve Sakoman <steve@sakoman.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 06 7月, 2010 1 次提交
-
-
由 Steve Sakoman 提交于
The purpose of this patch is to prepare for adding the OMAP4 architecture, which is Cortex A9 Cortex A8 and A9 both belong to the armv7 architecture, hence the name change. The two architectures are similar enough that substantial code can be shared. Signed-off-by: NAneesh V <aneesh@ti.com> Signed-off-by: NSteve Sakoman <steve@sakoman.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 08 6月, 2010 2 次提交
-
-
由 Vaibhav Hiremath 提交于
Consolidated SDRC related functions into one file - sdrc.c And also replaced sdrc_init with generic memory init function (mem_init), this generalization of omap memory setup is necessary to support the new emif4 interface introduced in AM3517. Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Vaibhav Hiremath 提交于
Consolidated SDRC related functions into one file - sdrc.c And also replaced sdrc_init with generic memory init function (mem_init), this generalization of omap memory setup is necessary to support the new emif4 interface introduced in AM3517. Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 13 2月, 2010 1 次提交
-
-
由 Tom Rix 提交于
Every omap3 board config file declared the global variable gpmc_cfg. This changes moves the declaration to a better location in the arch dependent header file cpu.h. Signed-off-by: NTom Rix <Tom.Rix@windriver.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 01 2月, 2010 1 次提交
-
-
由 Tom Rix 提交于
Every omap3 board config file declared the global variable gpmc_cfg. This changes moves the declaration to a better location in the arch dependent header file cpu.h. Signed-off-by: NTom Rix <Tom.Rix@windriver.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 04 1月, 2010 1 次提交
-
-
由 Robert P. J. Day 提交于
A number of config files define the V_PROMPT macro for the command-line prompt, only to immediately use that macro to define CONFIG_SYS_PROMPT, making V_PROMPT entirely superfluous. Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
-
- 20 12月, 2009 1 次提交
-
-
由 Tom Rix 提交于
The primary console of beagle is the serial header. A secondary console is to use the usbtty. The user can set this manually by doing setenv stdout usbtty; setenv stdin usbtty; setenv stderr usbtty saveenv usbtty will be usable by accessing the /dev/ttyACM0 on a linux host. Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
- 09 12月, 2009 1 次提交
-
-
由 Heiko Schocher 提交于
There is more and more usage of printing 64bit values, so enable this feature generally, and delete the CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL defines. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
- 28 11月, 2009 1 次提交
-
-
由 Nishanth Menon 提交于
Micron DDR timings based on: http://www.sakoman.net/cgi-bin/gitweb.cgi?p=x-load-omap3.git;a=blob;f=include/asm/arch-omap3/mem.h;h=e6fbfe3947f5d0d85fea776e30821d4017316d86;hb=HEAD Introduce Micron DDR timings and provide CONFIG_OMAP3_INFINEON_DDR and CONFIG_OMAP3_MICRON_DDR config options to allow for platform files to setup their timings as per the type of DDR selected Reported-by: Steve Sakoman in http://www.nabble.com/forum/Permalink.jtp?root=25779518&post=25959734&page=ySigned-off-by: NNishanth Menon <nm@ti.com>
-
- 19 10月, 2009 2 次提交
-
-
由 Sandeep Paulraj 提交于
This patch removes dependency on the sizes.h header file and removes all references to SZ_xx. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Steve Sakoman 提交于
Update default environment to support new kernel DSS2 subsystem and simplify rootfs type and location changes. Signed-off-by: NSteve Sakoman <sakoman@gmail.com> Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
- 13 10月, 2009 1 次提交
-
-
由 Tom Rix 提交于
This changes fixes an early i2c error. It appears that I2C is working because once a read or write error is detected, the omap24xx_i2c driver calls i2c_init inside its error handling check. While it is ok to attempt error handling this way, the boards must not depend on this side effect to initialize it's i2c. Instead of explicitly calling i2c_init for every board, use the generic arm initialization in lib_arm/board.c. By defining the config variable CONFIG_HARD_I2C, the omap3 i2c initialization is included in the init_sequence table. Run tested on Beagle. Compile tested on the omap3's Signed-off-by: NTom Rix <Tom.Rix@windriver.com> Acked-by: NDirk Behme <dirk.behme@googlemail.com>
-
- 04 10月, 2009 1 次提交
-
-
由 Tom Rix 提交于
This changes fixes an early i2c error. It appears that I2C is working because once a read or write error is detected, the omap24xx_i2c driver calls i2c_init inside its error handling check. While it is ok to attempt error handling this way, the boards must not depend on this side effect to initialize it's i2c. Instead of explicitly calling i2c_init for every board, use the generic arm initialization in lib_arm/board.c. By defining the config variable CONFIG_HARD_I2C, the omap3 i2c initialization is included in the init_sequence table. Run tested on Beagle. Compile tested on the omap3's Signed-off-by: NTom Rix <Tom.Rix@windriver.com> Acked-by: NDirk Behme <dirk.behme@googlemail.com>
-
- 08 8月, 2009 2 次提交
-
-
由 Dirk Behme 提交于
Signed-off-by: NMatthias Ludwig <mludwig@ultratronik.de> Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
由 Matthias Ludwig 提交于
Embedd chip select configuration into struct for gpmc config instead of having it completely separated as suggested by Wolfgang Denk on http://lists.denx.de/pipermail/u-boot/2009-May/052247.htmlSigned-off-by: NMatthias Ludwig <mludwig@ultratronik.de>
-
- 29 7月, 2009 1 次提交
-
-
由 Tom Rix 提交于
Because twl4030 now has its own device files, move exiting omap3 power_init_r to a new location. power_init_r is the only function in board/omap3/common. It initializes the twl4030 power for the board and enables the led. The power part of the the function is moved to twl4030_power_init in drivers/power/twl4030.c The power compilation is conditional on the existing config variable CONFIG_TWL4030_POWER. The led part is moved to twl4030_led_init in the new file drivers/misc/twl4030_led.c The led compilation is conditional on the new config variable CONFIG_TWL4030_LED The directory board/omap3/common was removed because power_init_r was the only function in it. Signed-off-by: NTom Rix <Tom.Rix@windriver.com> Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NHeiko Schocher <hs@denx.de>
-
- 19 7月, 2009 1 次提交
-
-
由 Wolfgang Denk 提交于
Commit 8d2effea added a warning for configurations that use NAND without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but failed to fix the affected boards. This patch covers the non-PPC boards that were missed in the previous patch (commit 170c1972). Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 13 6月, 2009 1 次提交
-
-
由 Stefan Roese 提交于
By changing the cmd_mtdparts to only use the MTD infrastructure and not the direct interface to the CFI NOR FLASH driver we now need to add the MTD infrastructure to all boards using those mtdparts commands. This patch adds those components: CONFIG_MTD_DEVICE (for all FLASH types) plus CONFIG_FLASH_CFI_MTD (for NOR FLASH) To all board maintainers: Please test this on your platforms and report any problems/issues found. Thanks. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Ron Madrid <info@sheldoninst.com> Cc: Georg Schardt <schardt@team-ctech.de> Cc: Michal Simek <monstr@monstr.eu> Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Martin Krause <martin.krause@tqs.de> Cc: Gary Jennejohn <garyj@denx.de> Cc: Ricardo Ribalda <ricardo.ribalda@uam.es>
-
- 01 5月, 2009 1 次提交
-
-
由 Manikandan Pillai 提交于
Signed-off-by: NDirk Behme <dirk.behme@googlemail.com> Signed-off-by: NManikandan Pillai <mani.pillai@ti.com>
-
- 30 4月, 2009 2 次提交
-
-
由 Dirk Behme 提交于
Remove remaining legacy NAND defines for Beagle, EVM, Overo and Pandora. Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
由 Sanjeev Premi 提交于
Use the functions print_cpuinfo() and checkboard() to display the cpu and board specific information. These functions reuse content from the existing function display_board_info() - which has been removed. Also, updated the existig OMAP3 configurations to define: - CONFIG_DISPLAY_CPUINFO - CONFIG_DISPLAY_BOARDINFO Signed-off-by: NSanjeev Premi <premi@ti.com>
-
- 27 4月, 2009 1 次提交
-
-
由 Dirk Behme 提交于
In recent U-Boot mmcinit changed to mmc init. Signed-off-by: NSteve Sakoman <steve@sakoman.com> Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
- 04 4月, 2009 1 次提交
-
-
由 Wolfgang Denk 提交于
According to the doc/feature-removal-schedule.txt, the "autoscr" command will be replaced by the "source" command in approximately 6 months from now. This patch prepares this change and starts a 6 month transition period as follows: - The new "source" command has been added, which implements exactly the same functionlaity as the old "autoscr" command before - The old "autoscr" command name is kept as an alias for compatibility - Command sequences, script files atc. have been adapted to use the new "source" command - Related environment variables ("autoscript", "autoscript_uname") have *not* been adapted yet; these will be renamed resp. removed in a separate patch when the support for the "autoscr" command get's finally dropped. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 31 3月, 2009 1 次提交
-
-
由 Ladislav Michl 提交于
Divisor field is called PTV not PVT. Signed-off-by: NLadislav Michl <ladis@linux-mips.org> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 29 3月, 2009 1 次提交
-
-
由 Ladislav Michl 提交于
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
-
- 26 3月, 2009 1 次提交
-
-
由 Nishanth Menon 提交于
http://www.denx.de/wiki/DULG/UBootCmdGroupFlash#UBootCmdFlMtdparts provides a flexible way to create and maintain u-boot mtd partitions. This allows commands such as "nand erase fs" to work and the user no longer needs to decode the absolute nand offsets. This patch enables this function for beagleboard Signed-off-by: NNishanth Menon <nm@ti.com> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-