- 27 10月, 2017 3 次提交
-
-
由 Yuantian Tang 提交于
On ls1012a soc, core clock source frequency is fixed at 100Mhz. Generic timer frequency is core clock source divided by 4, which is 25Mhz. Signed-off-by: NTang Yuantian <andy.tang@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Ashish Kumar 提交于
Signed-off-by: NAshish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Prabhakar Kushwaha 提交于
Memory allocated via malloc is not guaranteed to be zeroized. So explicitly use calloc instead of malloc. Signed-off-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 24 10月, 2017 1 次提交
-
-
由 York Sun 提交于
Commit 06ad970b ("powerpc: mpc85xx: Implemente workaround for CPU erratum A-007907") clears L1CSR2 for the boot core, but other cores don't run through the workaround. Add similar code for secondary cores to clear DCSTASHID field in L1CSR2 register. Signed-off-by: NYork Sun <york.sun@nxp.com>
-
- 23 10月, 2017 9 次提交
-
-
-
由 Masahiro Yamada 提交于
Commit dd74b945 ("ARM: uniphier: use pr_() instead of printf() where appropriate"), but I missed to update this file for some reason. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Add a simple documentation about how to use the Verified Boot on UniPhier boards. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
If the environment "verify" is set to n, the image verification is entirely skipped. Remove it as a preparation for verified boot. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
The default value of CONFIG_SYS_BOOTM_LEN, 0x800000, causes error when uncompressing Image.gz out of FIT image. Uncompressing Kernel Image ... Error: inflate() returned -5 Image too large: increase CONFIG_SYS_BOOTM_LEN Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
UniPhier 32-bit SoCs use CONFIG_SPL_OF_CONTROL. So, many nodes must be marked as dm-pre-reloc to prevent fdtgrep from stripping them off. Sprinkling U-Boot-specific properties all over the place is painful because DT files are synced with Linux from time to time. Split u-boot,dm-pre-reloc out to uniphier-v7-u-boot.dtsi, which is appended to UniPhier V7 DTS before the build. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Masahiro Yamada 提交于
The option is never enabled by anyone. Remove the code surrounded by its ifdef. This should be handled by the clock/reset drivers. CONFIG_UNIPHIER_ETH in scripts/config_whitelist.txt will be dropped by the next resync. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
I thought commit d37d3184 ("ARM: uniphier: enable DWC3 xHCI driver") enabled CONFIG_USB_DWC3_UNIPHIER, but CONFIG_USB_XHCI_DWC3 was missing in uniphier_v7_defconfig. Re-add. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
- 21 10月, 2017 3 次提交
-
-
由 Tom Rini 提交于
This was dropped by accident in the Kconfig conversion. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Adam Ford 提交于
We add the various SMC91XX symbols to drivers/net/Kconfig and then this converts the following to Kconfig: CONFIG_SMC911X CONFIG_SMC911X_BASE CONFIG_SMC911X_16_BIT CONFIG_SMC911X_32_BIT Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Apply to the rest of the tree, re-squash old and new patch] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_NAND_MXC CONFIG_NAND_OMAP_GPMC CONFIG_NAND_OMAP_GPMC_PREFETCH CONFIG_NAND_OMAP_ELM CONFIG_SPL_NAND_AM33XX_BCH CONFIG_SPL_NAND_SIMPLE CONFIG_SYS_NAND_BUSWIDTH_16BIT Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NHeiko Schocher <hs@denx.de> [trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues, add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 19 10月, 2017 9 次提交
-
-
-
由 Stefan Roese 提交于
I've missed to add the ACPI resume support to this x86 build target. This patch adds the ACPI resume support enabling S3 suspend / resume. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Heinrich Schuchardt 提交于
Up to now we depended on an exported variable to build u-boot.rom. We should be able to specify it in the configuration file, too. With this patch this becomes possible using the new Kconfig option CONFIG_BUILD_ROM. This option depends on CONFIG_X86 and is selected in qemu-x86_defconfig and qemu-x86_64_defconfig. Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Bin Meng 提交于
Azalia configuration may be different across boards, hence it's not appropriate to do that in the SoC level. Instead, let's make the SoC update_fsp_azalia_configs() routine as a weak version, and do the actual work in the board codes. So far it seems only som-db5800-som-6867 board enables the Azalia. Move the original codes into som-db5800-som-6867.c. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
At present we directly pass the Azalia config pointer to the FSP UPD. This updates to use a function to do the stuff, like Braswell does. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
So far there are two copies of Azalia struct defines with one in baytrail and the other one in braswell. This consolidates these two into one, put it in the common place, and remove the prefix pch_ to these structs to make their names more generic. This also corrects reset_wait_timer from us to ms. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
This is only needed when graphics console is used. For kernel with native graphics driver, this can be turned off to speed up. Change this option's default to n in the Kconfig. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
It was observed that when booting a Ubuntu 16.04 kernel, doing ACPI S3 suspend/resume sometimes causes the Ubuntu kernel hang forever. The issue is however not reproduced with a kernel built from i386/ x86_64 defconfig configuration. The unstability is actually caused by unexpected interrupts being generated during the S3 resume. For some unknown reason, FSP (gold4) for BayTrail configures the GPIO DFX5 PAD to enable level interrupt (bit 24 and 25). As this pin keeps generating interrupts during an S3 resume, and there is no IRQ requester in the kernel to handle it, the kernel seems to hang and does not continue resuming. Clear the mysterious interrupt bits for this pin. Reported-by: NStefan Roese <sr@denx.de> Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Tested-by: NStefan Roese <sr@denx.de> Reviewed-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
Adjust VGA rom address to 0xfffb0000 so that u-boot.rom image can be built again. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NStefan Roese <sr@denx.de>
-
- 18 10月, 2017 2 次提交
-
-
- 17 10月, 2017 7 次提交
-
-
由 Patrice Chotard 提交于
Remove useless local variable "s" and use directly function's parameter "output" Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Christophe Kerello 提交于
As "v" is a local variable in stm32_i2c_choose_solution() "v" has to be copied into "s" to avoid data abort in stm32_i2c_compute_timing(). Signed-off-by: NChristophe Kerello <christophe.kerello@st.com> Reviewed-by: NPatrick DELAUNAY <patrick.delaunay@st.com> Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Masahiro Yamada 提交于
No global pointer is used in this file. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Heinrich Schuchardt 提交于
On qemu errors like assert 2.999650001525879 >= 3 occur. According to the comment in the code the test is meant to be approximate. So we should accept some milliseconds less. Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: NStephen Warren <swarren@nvidia.com>
-
由 Heinrich Schuchardt 提交于
Update the script to version 0.26 (as of Linux v4.14-rc1) Keep our "penguin_chief". Keep our top_of_kernel_tree. The negative forms of the command line parameters are described when using --help. New options are --git-blame-signatures => when used with --git-blame, also include all commit signers --r => include reviewer(s) if any --letters => print all matching 'letter' types from all matching sections File .get_maintainer.ignore can be used to specify email addressees that shall be ignored. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
- 16 10月, 2017 6 次提交
-
-
由 Praneeth Bajjuri 提交于
'commit fa24eca1 ("omap: Add routine for setting fastboot variables")' adds initial support and usage of "fastboot getvar" command for DRA75x and DRA72x devices. and 'commit 0f9e6aee ("arm: dra76: Add support for ES1.0 detection")' adds initial dra76 device definition This patch is to extend usage of "fastboot getvar" for DRA76 device. Signed-off-by: NPraneeth Bajjuri <praneeth@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Vishal Mahaveer 提交于
DRA71x processors are reduced pin and software compatible derivative of DRA72 processors. Extend support for this revision in "getvar cpu" command. Signed-off-by: NVishal Mahaveer <vishalm@ti.com> [praneeth@ti.com: rebase to u-boot master] Signed-off-by: NPraneeth Bajjuri <praneeth@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Vishal Mahaveer 提交于
Add vendor partition to Android GPT table for eMMC. A Vendor image contains SoC-specific code and configuration. Prior to Android 8.0, the vendor partition was optional ; files belonging to these images were placed in boot.img or system.img with symlinks (such as /vendor >/system/vendor ) when absent. Android 8.0 makes the vendor partition mandatory The goal is to modularize Android partitions with standard interface between the Android Platform (on system.img ) and vendor-provided code(on vendor.img). This standard interface enables the Android Platform to be updated without affecting the SoC partitions. This makes it possible to upgrade a device system.img from Android 8.0 to Android P while other images (such as vendor.img) remain at Android 8.0. This modularity enables timely Android platform upgrades (such as monthly security updates ) without requiring SoC/ODM partners to update SoC- and device-specific code. Signed-off-by: NVishal Mahaveer <vishalm@ti.com> Signed-off-by: NPraneeth Bajjuri <praneeth@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Praneeth Bajjuri 提交于
Add vendor partition to Android GPT table for eMMC. A Vendor image contains SoC-specific code and configuration. Prior to Android 8.0, the vendor partition was optional ; files belonging to these images were placed in boot.img or system.img with symlinks (such as /vendor >/system/vendor ) when absent. Android 8.0 makes the vendor partition mandatory The goal is to modularize Android partitions with standard interface between the Android Platform (on system.img ) and vendor-provided code(on vendor.img). This standard interface enables the Android Platform to be updated without affecting the SoC partitions. This makes it possible to upgrade a device system.img from Android 8.0 to Android P while other images (such as vendor.img) remain at Android 8.0. This modularity enables timely Android platform upgrades (such as monthly security updates ) without requiring SoC/ODM partners to update SoC- and device-specific code. Signed-off-by: NPraneeth Bajjuri <praneeth@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Heinrich Schuchardt 提交于
Fix typos in USB tty driver. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Bin Meng 提交于
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
-