- 17 5月, 2017 15 次提交
-
-
由 Bin Meng 提交于
In enter_acpi_mode() PM1_CNT register is changed to PM1_CNT_SCI_EN directly without preserving its previous value. Update to change the register access to read-modify-write (RMW). Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
Call board_final_cleanup() before write_tables(), so that anything done in board_final_cleanup() on a normal boot path is also done on an S3 resume path. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
When SeaBIOS is being used, U-Boot reserves a memory area to be used for configuration tables like ACPI. But it should not be cleared otherwise ACPI table will be missing. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
At the end of pre-relocation phase, save the new stack address to CMOS and use it as the stack on next S3 boot for fsp_init() continuation function. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
This adds a library that provides CMOS (inside RTC SRAM) access at a very early stage when driver model is not available yet. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
In an S3 resume path, U-Boot does everything like a cold boot except in the last_stage_init() it jumps to the OS resume vector. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
This adds one API acpi_find_wakeup_vector() to locate OS wakeup vector from the ACPI FACS table, to be used in the S3 boot path. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
This adds a wake up stub before jumping to OS wake up vector. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
U-Boot itself as well as everything that is consumed by U-Boot (like heap, stack, dtb, etc) needs to be reserved and reported in the E820 table when S3 resume is on. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
When U-Boot is built without ACPI S3 support, it should not report S3 in the ACPI table otherwise when kernel does STR it won't work. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
Add one member in the global data to store previous sleep state, and display the state during boot in print_cpuinfo(). Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
When ACPI S3 resume is turned on, we should pass different boot mode to FSP init instead of default BOOT_FULL_CONFIG. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
This adds OS_RESUME (0x40) and RESUME_FAILURE (0xed) post codes. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
This adds APIs for determining previous sleep state from ACPI I/O registers, as well as clearing sleep state on BayTrail SoC. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
This introduces a Kconfig option for ACPI S3 resume, as well as a header file to include anything related to ACPI S3 resume. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NStefan Roese <sr@denx.de>
-
- 16 5月, 2017 17 次提交
-
-
git://git.denx.de/u-boot-mmc由 Tom Rini 提交于
- Add #undef CONFIG_DM_MMC_OPS to omap3_logic in the SPL build case, to match other TI platforms in the same situation. Signed-off-by: NTom Rini <trini@konsulko.com>
-
-
由 Wenyou Yang 提交于
To fix the timeout of sending the write command, enable the quirk SDHCI_QUIRK_WAIT_SEND_CMD. Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Jernej Skrabec 提交于
This patch adds support for TV encoder clocks which will be used later. Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
-
由 Jernej Skrabec 提交于
Newer SoCs use same TV encoder unit. Split it out so it can be reused with new DM video driver. Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Philipp Tomsich 提交于
Due to a typo, the 24 bit-per-pixel configuration ends in 24BMP instead of 24BPP. This change renames it throughout the source tree for consistency and to make moving these options into Kconfig easier and less error-prone. Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NHannes Schmelzer <hannes.schmelzer@br-automation.com>
-
由 Philipp Tomsich 提交于
Instead of having drivers/video/rockchip/Kconfig point outside of its hierarchy for dw_hdmi.o, we should use a configuration-option to include the Designware HDMI support. This change introduces a new config option (not to be selected via menuconfig, but to be selected from a dependent video driver's configuration option) that enables dw_hdmi.o and selects it whenever the HDMI support for Rockchip SoCs is selected. Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Jernej Skrabec 提交于
Some DVI monitors don't work in HDMI mode. Set it only if edid data explicitly states that it is supported. Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Jernej Skrabec 提交于
Some DVI monitors don't show anything in HDMI mode since audio stream confuses them. To solve this situation, this commit adds HDMI flag in timing data and sets it accordingly during edid parsing. First existence of extension block is checked. If it exists and it is CEA861 extension, then data blocks are checked for presence of HDMI vendor specific data block. If it is present, HDMI flag is set. Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Jernej Skrabec 提交于
Timing flags are never set, so they may contain garbage. Since some drivers check them, video output may be broken on those drivers. Initialize them to 0 and check for few common flags. Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
-
由 Masahiro Yamada 提交于
Recent commits of DTC introduced new warnings checking PCI and simple buses, unit address formatting, and stricter node and property name checking. Disable the new DTC warnings by default. As before, warnings are enabled with W=*. The strict node and property name checks are a bit subjective, so they are only enabled for W=2. (This policy reflects the commit 8654cb8d0371 of Linux.) Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Adam Ford 提交于
Enable TI_COMMON_CMD_OPTIONS and remove similar options from the defconfig. Updated with savedefconfig CMD_USB isn't enabled yet. I have some testing to do with musb. Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Adam Ford 提交于
Now that CMD_POWEROFF can turn off the twl4030, let's imply that just incase someone wants to disable it. Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
Follow the exiting logic for the i.MX options when migrating this option. Cc: Marek Vasut <marex@denx.de> Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NMarek Vasut <marex@denx.de>
-
由 Tom Rini 提交于
The following options are migrated over fully now: - USB_EHCI_ATMEL - USB_EHCI_MARVELL - USB_EHCI_MX6 - USB_EHCI_MX7 - USB_EHCI_MSM - USB_EHCI_ZYNQ - USB_EHCI_GENERIC This also requires fixing the depends on USB_EHCI_MARVELL as it's used by Orion5X and Kirkwood as well. Cc: Marek Vasut <marex@denx.de> Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NMarek Vasut <marex@denx.de>
-
由 Tom Rini 提交于
Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig. For a few SoCs, imply or default y this if USB is enabled. In some cases we had not already migrated to CONFIG_USB so do that as well. Cc: Marek Vasut <marex@denx.de> Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NMarek Vasut <marex@denx.de>
-
- 15 5月, 2017 8 次提交
-
-
由 Tom Rini 提交于
In order to be able to migrate the various SoC EHCI CONFIG options we first need to finish the switch from CONFIG_USB_EHCI to CONFIG_USB_EHCI_HCD. Cc: Marek Vasut <marex@denx.de> Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NMarek Vasut <marex@denx.de>
-
由 Tom Rini 提交于
The symbol CONFIG_OMAP3_LOGIC_USE_NEW_PRODUCT_ID was recently dropped from usage and CONFIG_OMAP3_MICRON_DDR is unused in code. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
The symbol CONFIG_OMAP_VC_I2C_HS_MCODE always uses the default value. Restructure the comment and code such that if a need arises later to use another value we can address this then. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
Move this entry to Kconfig. As it is a hardware watchdog, select HW_WATCHDOG. While we could default to enabling this for all platforms, it is currently only enabled by default on AM33XX, so keep that logic today. Cc: Roger Meier <r.meier@siemens.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
This particular quirk is not enabled in any config files today. It does however exist and is handled correctly in device trees and via CONFIG_DM_SPI. So we drop the symbol now and add a comment to indicate that any (new) boards that require this quirk need to enable DM_SPI instead. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
The symbols CONFIG_OMAP3_GPIO_X control if we enable the clocks for a given GPIO bank in U-Boot. select the required banks for each target. In some cases we need to also migrate from CONFIG_USB_EHCI (deprecated, in include/configs/) to CONFIG_USB_EHCI_HCD as we only require the GPIO bank to be enabled if USB is also enabled. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
This driver is used often enough such that we want to have this enabled by default on any ARCH_OMAP2PLUS board, and this only compiles on ARCH_OMAP2PLUS due to required defines, so mark that as the depends. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
We no longer have a need for a per-board CONFIG_OMAP3_xxx define (we have CONFIG_TARGET_xxx when this is required), so drop these unused references. Signed-off-by: NTom Rini <trini@konsulko.com>
-