Signed-off-by: NAlessandro Rubini <rubini@unipv.it>
Acked-by: NAndrea Gallo <andrea.gallo@stericsson.com>

- fix board support following relocation changes
- switch to boards.cfg
- disable i2c to keep size under 128kiB (1 sector)
Signed-off-by: NEric Bénard <eric@eukrea.com>

- update to new relocation code
- switch to boards.cfg
- get rid of LEGACY (still a little hack in .h to compile)
- add nand boot configuration
- boot tested for the following configurations :
	9260 (64MB RAM & nor boot)
	9260_nand (64MB RAM & nand boot)
	9G20_128M (128MB RAM & nor boot)
	9G20_nand_128M (128MB RAM & nand boot)
	(nor boot is using lowlevel init)
Signed-off-by: NEric Bénard <eric@eukrea.com>

Board support for the DIG297 board manufactured by Comelit Group SpA.
It is a custom board based on the BeagleBoard <http://beagleboard.org/> by
Texas Instruments.

The board support is based on the BeagleBoard implementation.
Signed-off-by: NLuca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

It is a low cost reference design based on Sitara AM3517 SoC from Texas Instruments
Please refer to <www.craneboard.org> for more details.
Signed-off-by: NSrinath <srinath@mistralsolutions.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg
Signed-off-by: NJason Liu <r64343@freescale.com>

The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg
Signed-off-by: NStefano Babic <sbabic@denx.de>

Old address of RESET_VECTOR were overwritten by the bss sector, making
impossible its run from xmd.
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NGraeme Russ <graeme.russ@gmail.com>

PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and
PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as
1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from
CPC after PBL completes RCW and PBI phases.
Signed-off-by: NChunhe Lan <b25806@freescale.com>
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NShaohui Xie <b21989@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NChong Huang <chuang@ucrobotics.com>
Signed-off-by: NHaitao Zhang <minipanda@linuxrobot.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Info about the hardware can be found here:
	http://www.dilnetpc.com/dnp0086.htmSigned-off-by: NAndreas Schallenberg <Andreas.Schallenberg@3alitydigital.de>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

We implement our own mmc_get_env_addr since the environment variables are
written to just after the u-boot image on SDCard, so we must read the MBR
to get the start address and code length of the u-boot image, then
calculate the address of the env.
Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: NZhao Chenhui <b35336@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NJiang Yutang <b14898@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for 36-bit address map for NOR, SD, and SPI boot cfgs.
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Au1x00 is a SoC and its specific code should reside in an own
SoC subdirectory. Also add -mtune=4kc flag for CPU optimization.
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Thomas Lange <thomas@corelatus.se>
Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>

IncaIP is a SoC and its specific code should reside in an own
SoC subdirectory. Also add -mtune=4kc flag for CPU optimization.
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>

All current CPUs and SoCs are based on MIPS32 arch. The complete
code resides in the global arch/mips/cpu directory. This is not
suitable if other MIPS architectures like MIPS64 or Octeon should
be supported in the future.

To achieve this the current CPU code is moved to its own mips32
subdirectory. All MIPS32 boards have to use mips32 as config switch
in board.cfg.
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Thomas Lange <thomas@corelatus.se>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>

The Purple SoC and eval board are not actively maintained since years.
This patch removes the support completely as aggreed with Wolfgang Denk.
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>

DKB is a Development Board for PANTHEON TD/TTC(pxa920/pxa910) with
* Processor upto 806Mhz
* LPDDR1/2
* x8/x16 SLC/MLC NAND
* Footprints for eMMC & MMC x8 card

With Peripherals:
* Parallel LCD I/F
* Audio codecs (88PM8607)
* MIPI CSI-2 camera
* Marvell 88W8787 802.11n/BT module
* Marvell 2G/3G RF
* Dual analog mics & speakers, headset jack, LED, ambient
* USB2.0 HS host, OTG (mini AB)
* GPIO, GPIO expander with DIP switches for easier selection
* UART serial over USB, CIR

This patch adds basic board support with DRAM and UART functionality
Signed-off-by: NLei Wen <leiwen@marvell.com>
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>

Signed-off-by: NTom Warren <twarren@nvidia.com>

Signed-off-by: NTom Warren <twarren@nvidia.com>

Position independant functionality is due for removal from the x86
architecture, so create two distinct configurations - One for Flash and
one for SRAM

We should have been defining the actual board name in the options, not
the processor.  Fix this for P1011RDB, P1020RDB, P2010RDB, and P2020RDB.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>
Acked-by: NStefan Roese <sr@denx.de>

Board support for the Guntermann & Drunck DLVision-10G.
Adds support for multiple FPGAs per board for gdsys 405ep
architecture.
Adds support for dual link osd hardware for gdsys 405ep.
Signed-off-by: NDirk Eibach <eibach@gdsys.de>
Signed-off-by: NStefan Roese <sr@denx.de>

At the same time, fix up CPU_CLOCK_RATE to have the CONFIG_ prefix to
work with boards.cfg.
Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>

CONFIG_QEMU_MIPS is already provided by <configs/qemu-mips.h>, so we
don't generate it using the options fields in boards.cfg.
Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>

CONFIG_GTH2 is already provided by <configs/gth2.h>, so we don't
generate it using the options fields in boards.cfg.
Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>

The R0P7757LC0030RL board has SH7757, 256MB DDR3-SDRAM, SPI ROM,
Ethernet, and more.

This patch supports the following functions:
 - 256MB DDR3-SDRAM
 - SPI ROM
 - Ethernet
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

This patch adds support for Samsung s5pc210 universal board
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>

This patch adds support for CM-T35 board
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

The patch adds suupport for the Freescale's mx35pdk board
(known as well as mx35_3stack).

The board boots from the NOR flash. Following devices
are supported:
 - two ethernet devices (FEC and SMC911x on debug board)
 - I2C
 - PMIC (MC13892) via I2C interface
 - UART
 - NOR flash (64MB)
 - NAND flash (2GB)
 - basic access to mc9sdz60 registers via I2C interface
Signed-off-by: NStefano Babic <sbabic@denx.de>

Supported:
MMC
IDE
PMIC
SPI flash
LEDs

I can boot the kernel supplied by freescale/genesi with this from MMC card
and/or PATA disk.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Add initial support for MX53EVK board support.
FEC, SD/MMC, UART, I2C, have been supported.
Signed-off-by: NJason Liu <r64343@freescale.com>

Mpq101 is a RapidIO development board in AMC form factor, featuring MPC8548
processor, 512MB of hardwired DDR2 RAM, 128MB of hardwired NAND flash
memory, real time clock and additional serial EEPROM on i2c bus (enabled).
USB controller is available, but not presently enabled.

Additional board information is available at:
http://www.mc.com/products/boards/ensemble_mpq101_rapidio_powerquicc_iii.aspx

Environment is configured to precede the actual u-boot image so that it's
located at the beginning of flash erase block (made necessary by the recent
changes to the embedded environment handling). This is achieved by means of
custom ld script.
Signed-off-by: NAlex Dubov <oakad@yahoo.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

There is not break character between board name and CPU.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

difference to previous board version:
- M29W128GH flash from Numonyx
- SDRAM ISSI IS45S16800 (Option A2 105°C)
- rev5 uses RTC RV-3029-C2
- update cs0 and cs1 baseaddr and length
  depending on the detected flash size.
- added Werner Pfister <Pfister_Werner@intercontrol.de>
  as maintainer for the digsy board variants
- As the M29W128GH needs a special flash_cmd_reset()
  document that in the new file doc/README.cfi.
- move "#endif /* CONFIG_CMD_IDE */" to the right place
- remove LOWBOOT config option for digsy_mtc and digsy_mtc_rev5
  boards
- change doc/README.cfi as Stefan Roese suggested
Signed-off-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NStefan Roese <sr@denx.de>
Acked-by: NDetlev Zundel <dzu@denx.de>
cc: Wolfgang Denk <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Werner Pfister <Pfister_Werner@intercontrol.de>
cc: Detlev Zundel <dzu@denx.de>

The MPC852 based mgsuvd and kmsupx4 boards from keymile
were initially ported but later on not developed further. So
the respective files were removed to avoid unneeded merging
and maintenance.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher<hs@denx.de>