- 28 4月, 2014 17 次提交
-
-
由 Nobuhiro Iwamatsu 提交于
CONFIG_SH_TMU_CLK_FREQ of koelsch is calculated from the external clock. This defines RMOBILE_XTAL_CLK, this updates the calculation of CONFIG_SH_TMU_CLK_FREQ. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This update QoS version 0.240 for ES1 and version 0.310 for ES2. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
There is koelsch where ES2 revision of R8A7791 was put on. This is different in Qos setting. This adds Qos setting for ES2 revision of R8A7791. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
There is ES2 is a new revision to R8A7791. This adds support this revision. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
There is ES2 is a new revision to R8A7790. This adds support this revision. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
The print_cpuinfo fucntion has same code. It has a code of many common. This adds a table of CPU information, duplicate using for-loop. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
These functions are defined but has no prototype declaration. Add them. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This adds rmobile_get_cpu_rev_fraction to get fraction revision for R-Car SoCs. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Value that can be obtained in the rmobile_get_cpu_rev_integer() starts at 0. However, revisions to start from 1, which adds 1. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Functions to get the CPU information of R8A7790 and R8A7791 are common. This merges these as cpu_info-rcar.c. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Lagar board has NOR-Flash. But user uses SPI-Flash ROM instead of NOR-Flash. This removed the setting of NOR-Flash. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This changes from r8a7790_ to rcar_. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Koelsch board has NOR-Flash. But user uses SPI-Flash ROM instead of NOR-Flash. This removed the setting of NOR-Flash. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This changes from r8a7791_ to rcar_. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
L2CTLR only need to update for cluster 0. This changes L2CTLR to initialize only when cluster is 0. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Header files of R8A7790 and R8A7791 have common part of many. This coordinates as rcar-base.h. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
- 22 4月, 2014 2 次提交
-
-
由 Albert ARIBAUD 提交于
-
由 Albert ARIBAUD 提交于
-
- 18 4月, 2014 21 次提交
-
-
由 Tom Rini 提交于
QSPI booting on this board does not use SPL, so drop SPI-SPL related options. Signed-off-by: NTom Rini <trini@ti.com>
-
由 Manish Badarkhe 提交于
Make funtions static which are locally used in file and remove the declaration from header file. Signed-off-by: NManish Badarkhe <badarkhe.manish@gmail.com>
-
由 Tom Rini 提交于
In the case of SPL or NOR_BOOT (no SPL involved) we need to include certain code in the build. Use !CONFIG_SKIP_LOWLEVEL_INIT rather than CONFIG_SPL_BUILD || CONFIG_NOR_BOOT to make the code clearer, and to make supporting XIP QSPI boot clearer in the code. Signed-off-by: NTom Rini <trini@ti.com> Reviewed-by: NWolfgang Denk <wd@denx.de>
-
由 Nishanth Menon 提交于
ti_omap3_common contains a lot of common header definitions that help reduce the size of the zoom1 config file. So, use the generic header and customize as needed for the platform (example: no spl). Signed-off-by: NNishanth Menon <nm@ti.com>
-
由 Nishanth Menon 提交于
We do not use ttyS2 anymore in Linux, it changed to ttyO2 a few years back. never too late to update. Signed-off-by: NNishanth Menon <nm@ti.com>
-
由 Nishanth Menon 提交于
Boot from zImage and fdt_file if uImage is not available to maintain the legacy behavior. Signed-off-by: NNishanth Menon <nm@ti.com>
-
由 Nishanth Menon 提交于
This is more in line with commits 664979a2(omap3_beagle: remove JFFS2 support.) and 102ce9ea (omap3_beagle: enable CMD_FS_GENERIC and simplify load of image/ramdisk) CMD_FS_GENERIC allows us to simplify where we load up our image from either from ext2/fat etc. So, lets use that instead of cumbersome options we'd have to use. Sticking with existing conventions, defaults will be: bootfile=uImage bootpart=0:1 (first partition) bootdir=/ (/ in first partition) Signed-off-by: NNishanth Menon <nm@ti.com>
-
由 Nishanth Menon 提交于
Basic networking commands for usability. Signed-off-by: NNishanth Menon <nm@ti.com>
-
由 Nishanth Menon 提交于
Zoom1 was wrongly setup for LAN91C96. Fix it by enabling LAN9211. Signed-off-by: NNishanth Menon <nm@ti.com>
-
由 Nishanth Menon 提交于
zoom1 uses LAN9211 configured over GPMC Chip Select 1. Signed-off-by: NNishanth Menon <nm@ti.com>
-
由 Nishanth Menon 提交于
CONFIG_SYS_GENERIC_BOARD should now be enabled for generic functionality Further information in doc/README.generic-board Signed-off-by: NNishanth Menon <nm@ti.com>
-
由 Karicheri, Muralidharan 提交于
Ethernet driver configures the CPSW, SGMI and Phy and uses the the Navigator APIs. The driver supports 4 Ethernet ports and can work with only one port at a time. Port configurations are defined in board.c. Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com> Signed-off-by: NWingMan Kwok <w-kwok2@ti.com>
-
由 Vitaly Andrianov 提交于
Multicore navigator consists of Network Coprocessor (NetCP) and Queue Manager sub system. More details on the hardware can be obtained from the following links:- Network Coprocessor: http://www.ti.com/lit/pdf/sprugz6 Multicore Navigator: http://www.ti.com/lit/pdf/sprugr9 Multicore navigator driver implements APIs to configure the Queue Manager and NetCP Pkt DMA. Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com> Signed-off-by: NWingMan Kwok <w-kwok2@ti.com> Acked-by: NTom Rini <trini@ti.com>
-
由 Karicheri, Muralidharan 提交于
currently only spi0 is enabled on k2hk evm. This configuration update is needed to enable spi1 and spi2. Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com> Acked-by: NTom Rini <trini@ti.com>
-
由 Karicheri, Muralidharan 提交于
Currently davinci spi driver supports only bus 0 cs 0. This patch allows driver to support bus 1 and bus 2 with configurable number of chip selects. Also defaults are selected in a way to avoid regression on other platforms that uses davinci spi driver and has only one spi bus. Signed-off-by: NRex Chang <rchang@ti.com> Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com> Reviewed-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>
-
由 Vitaly Andrianov 提交于
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please refer the ti/k2hk_evm/README for details on the board, build and other information. This patch add support for keystone architecture and k2hk evm. Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com> Signed-off-by: NWingMan Kwok <w-kwok2@ti.com> Signed-off-by: NSandeep Nair <sandeep_n@ti.com>
-
由 Vitaly Andrianov 提交于
- add davinci driver to new multibus/multiadpater support - adapted all config files, which uses this driver Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com> Acked-by: NHeiko Schocher <hs@denx.de>
-
由 Karicheri, Muralidharan 提交于
This patch moves the davinci i2c_defs.h file to drivers.i2c directory. It will allow to reuse the davinci_i2c driver for TI Keystone2 SOCs. Not used "git mv" command to move the file because small part of it with definitions specific for Davinci SOCs has to remain in the arch/arm/include/asm/arch-davinci. Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com> Acked-by: NTom Rini <trini@ti.com>
-
由 Karicheri, Muralidharan 提交于
This patch introduces a configurable mechanism to disable subpage writes in the DaVinci NAND driver. Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com> Acked-by: NTom Rini <trini@ti.com>
-
由 Vitaly Andrianov 提交于
This patch add basic support for the architecture timer found on recent ARMv7 based SoCs. Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
-
由 Karicheri, Muralidharan 提交于
This patch add support for gpimage format as a preparatory patch for porting u-boot for keystone2 devices and is based on omapimage format. It re-uses gph header to store the size and loadaddr as done in omapimage.c Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com> Acked-by: NTom Rini <trini@ti.com>
-