These take the 'struct udevice *' as an argument, not the
'struct xilinx_pcie *` which is a local variable. Fix the comments to
match the code.
Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

We have limited stack in SPL builds.  Drop itrblock and move to
malloc/free of itr to move this off of the stack.  As part of this fix a
double-free issue in fat_size().
Signed-off-by: NTom Rini <trini@konsulko.com>
---
Rework to use malloc/free as moving this to a global overflows some SH
targets.

Support spi driver and can detect MX25U1635E flash on AE3XX board.

Verification:

sf probe 0:0 50000000 0
spi_flash_std_probe(sf_Probr.c)
	spi_flash_probe_slave(sf_Probr.c)
	SF: Detected mx25u1635e with page size 256 Bytes, erase size 4 KiB, total 2 MiB
	NDS32 # sf test 0x100000 0x1000
	SPI flash test:
	0 erase: 34 ticks, 117 KiB/s 0.936 Mbps
	1 check: 15 ticks, 266 KiB/s 2.128 Mbps
	2 write: 21 ticks, 190 KiB/s 1.520 Mbps
	3 read: 11 ticks, 363 KiB/s 2.904 Mbps
	Test passed
	0 erase: 34 ticks, 117 KiB/s 0.936 Mbps
	1 check: 15 ticks, 266 KiB/s 2.128 Mbps
	2 write: 21 ticks, 190 KiB/s 1.520 Mbps
	3 read: 11 ticks, 363 KiB/s 2.904 Mbps
Signed-off-by: Nrick <rick@andestech.com>

Add spi dts node and enable spi dm flash config.
Signed-off-by: Nrick <rick@andestech.com>

To support MACRONIX MX25U1635E 16M-BIT flash.
Signed-off-by: Nrick <rick@andestech.com>

After soft reset complete, write mac address immediately will fail.
Add delay to work around this problem.
Signed-off-by: Nrick <rick@andestech.com>

Enable cache and ftmac100 performance can be improved.
Signed-off-by: Nrick <rick@andestech.com>

Add cache inval and flush when rx and tx.
Signed-off-by: Nrick <rick@andestech.com>

move #include <asm/setup.h> from bootm.c to bootm.h
Signed-off-by: Nrick <rick@andestech.com>

Add #include <asm/mach-types.h> to fix it.
Signed-off-by: Nrick <rick@andestech.com>

Add Serial Download Protocol support (SDP), which allows loading
SPL and u-boot.img via imx_usb_loader tool as explained in
doc/README.sdp.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>

Instead of having every board file to add its own g_dnl_bind_fixup()
implementation, move it to the common imx6 SPL code.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: NŁukasz Majewski <lukma@denx.de>

Define i2c mux configuration.  Add new vpd_reader which is used to read
vital product data.  Read VPD from EEPROM and set eth0 MAC address.
Signed-off-by: NIan Ray <ian.ray@ge.com>
Signed-off-by: NJose Alarcon <jose.alarcon@ge.com>

The hummingboard2 is slightly different to the cubox i and to the
hummingboard. The GPIO pin info to probe came from solidruns
for of u-boot on github.
https://github.com/SolidRun/u-boot-imx6/blob/imx6/board/solidrun/mx6_cubox-i/mx6_cubox-i.c#L569-L589
I have tested on a hummingboard-edge witha  imx6 solo and 512mb of
ram.
Signed-off-by: NDennis Gilmore <dgilmore@redhat.com>

Increase serialno_str to 17 bytes so it can hold the 16 bytes long serial
nummer and the terminating null byte added by snprintf.
Signed-off-by: NKlaus Goger <klaus.goger@theobroma-systems.com>

After Simon's patch, the dtoc can work with 64bit address,
so we need to fix reg number for it.
Depend on Simon's patch set:
https://patchwork.ozlabs.org/cover/807266/Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

After Simon's patch, the dtoc can work with 64bit address,
so we need to fix reg number for it.
Depend on Simon's patch set:
https://patchwork.ozlabs.org/cover/807266/Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

The RK3368 TPL stage always returns to the BootROM, so it has no need
for the eMMC, SD and SPI nodes.  This marks those nodes (that should
be included in SPL, but not TPL) as 'u-boot,dm-spl'.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

With the new 32/64bit-aware dtoc, the type of reg is fdt64_t and the
OF_PLATDATA structure layout changes.  This adjusts the DMC driver for
the RK3368 to track these changes.

For the time being (i.e. until regmap_init_mem_platdata works for the
64bit case), we won't use regmap_init_mem_platdata here and simply
access of_plat.reg[] directly.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

With dtoc emitting fdt64_t for addresses (and region sizes), the array
indices for accessing the reg[] array needs to be adjusted.  This
adjusts the Rockchip DM timer driver to correctly handle OF_PLATDATA
given this new structure layout.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

With the critical drivers ready for switching to a live tree, we can
now enable it in the defconfig for the RK3399-Q7.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

With the dev_read_addr_ptr function available, we can change the
efuse driver to use it (and eliminate the explicit type-cast).
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Update the clock driver for the RK3399  to support a live device tree.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

On the RK3399-Q7, we need to turn on the on-module USB hub before using the
USB host interfaces (only the OTG interface is directly connected to the edge
connector).  This drops the deprecated 'rockchip,vbus-gpio' property and uses
a fixed regulator to turn on the USB hub.

References: 26a8b80f "usb: host: xhci-rockchip: use fixed regulator to control vbus"
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

The generic ehci-driver (ehci-generic.c) will try to enable the clocks
listed in the DTSI. If this fails (e.g. due to clk_enable not being
implemented in a driver and -ENOSYS being returned by the clk-uclass),
the driver will bail our and print an error message.

This implements a minimal clk_enable for the RK3399 and supports the
clocks mandatory for the EHCI controllers; as these are enabled by
default we simply return success.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Add the missing target and pinctrl config for rk3368 sheep board
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

Add the ENV_MEM_LAYOUT_SETTINGS to CONFIG_EXTRA_ENV_SETTINGS
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

This patch adds support for Vyasa RK3288 initial board
from Amarula Solutions.
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

On the RK3399, we will have either OF_PLATDATA or full OF_CONTROL
enabled: this allows the use of syscon to retrieve the addresses of
GRF and SGRF (except for the early debug UART setup, which runs so
early that the device-model is not initialised).

This removes the hard-coded addresses and goes through syscon to
retrieve the base-addresses of GRF and SGRF. After that, we use
the structure definitions to locate the respective registers.

In addition to this, the inclusion of header files is also cleaned up:
- all headers are included at the beginning (there was a spurious
  inclusion of the grf header from within a function)
- all #include statements for unused headers are removed
- the remaining #include statements are sorted (while keeping common.h
  included in front)
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This adds OF_LIVE and BOOTSTAGE support for the RK3368-uQ7 and
regenerates the defconfig (picking up a few changes/reorderings) from
upstream Kconfig changes.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

To support bootstage recording, we want to mark our DM timer as the
tick-timer; this triggers the support for 'trying harder' to read the
timer in the Rockchip DM timer driver, even if the device model isn't
ready yet.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

Remove a comment claiming that this driver only supports the RK3288,
as we also use it on the RK3368, RK3399 and (most likely) on other
variants.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

Version-changes: 2
- use the dev_read_addr_ptr function in rk_gpio.c

Update the Rockchip GPIO-bank driver to support a live tree.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

Version-changes: 2
- use the dev_read_addr_ptr function in rk_gpio.c

Update the Rockchip I2C driver to support livetree.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: NHeiko Schocher <hs@denx.de>

Remove header file includes that have been left over after the
conversion to livetree-support.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

Update the Rockchip SDHCI wrapper to support a live device tree.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

Version-changes: 2
- use the dev_read_addr_ptr function in	rockchip_sdhci.c

Update the Rockchip SPI driver to support a live device tree.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NJagan Teki <jagan@openedev.com>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>