With updated moveconfig.py and an better default, re-generate
the migration of BOOTDELAY to the defconfig.
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig
Signed-off-by: NTom Rini <trini@konsulko.com>

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND.  Due to how we have used this historically
we need to take further care here when converting.
Signed-off-by: NTom Rini <trini@konsulko.com>

Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files.  Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.
Signed-off-by: NTom Rini <trini@konsulko.com>

Move this option to Kconfig and tidy up existing boards.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Add CMD_GPIO to Kconfig and run tools/moveconfig.py .
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Some boards' defconfigs are disordered. Reorder them.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>

Discard MX6UL from CONFIG_SYS_EXTRA_OPTIONS, since we default
select MX6UL for mx6ul_14x14_evk board.
Signed-off-by: NPeng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>

Add enet support for mx6ul_14x14_evk board:
1. add pinmux settings
2. implement board_eth_init
3. implement board_phy_config
Signed-off-by: NPeng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>

Move TARGET_xx Kconfig option based on mx6 to arch/arm/cpu/armv7/mx6/Kconfig.
Add enable "CONFIG_ARCH_MX6" for boards based on mx6.
Then we can choose target boards using "make ARCH=arm menuconfig"
with ARCH_MX6 defined.

If using original way, we have no chance to enable ARCH_MX6 when
"make menuconfig". Even define CONFIG_ARCH_MX6=y in xx_defconfig,
kconfig will complains "arch/../configs/platinum_titanium_defconfig:3:
warning: override: TARGET_PLATINUM_TITANIUM changes choice state"
Signed-off-by: NPeng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Soeren Moch <smoch@web.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: NStefano Babic <sbabic@denx.de>
Acked-by: NSoeren Moch <smoch@web.de>
Acked-by: NOtavio Salvador <otavio@ossystems.com.br>
Acked-by: NChristian Gmeiner <christian.gmeiner@gmail.com>

Several files are out of order. This means that when the moveconfig tool
moves CONFIG options to Kconfig it generates a large diff. To avoid this,
reorder the files first.
Signed-off-by: NSimon Glass <sjg@chromium.org>

1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
   supports sd for usdhc2, but can do hardware rework to make usdhc2 support
   emmc.

Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img

U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)

CPU:   Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU:   Commercial temperature grade (0C to 95C)CPU:   Thermal invalid data, fuse: 0x0
 - invalid sensor device
 Reset cause: POR
 Board: MX6UL 14x14 EVK
 I2C:   ready
 DRAM:  512 MiB
 MMC:   FSL_SDHC: 0, FSL_SDHC: 1
 *** Warning - bad CRC, using default environment

 In:    serial
 Out:   serial
 Err:   serial
 Net:   CPU Net Initialization Failed
 No ethernet found.
 Hit any key to stop autoboot:  0
Signed-off-by: NPeng Fan <Peng.Fan@freescale.com>