This patch moved ethernet PHY configs of ZynqMP boards
to respective defconfig.
Signed-off-by: NVipul Kumar <vipulk@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This patch moved ethernet PHY configs of Microblaze board to
respective defconfig.
Signed-off-by: NVipul Kumar <vipulk@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This patch moved ethernet PHY configs of Zynq boards
to respective defconfig.
Signed-off-by: NVipul Kumar <vipulk@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Ethernet is not enabled that's why this alias should be completely
unused.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

The same change is done for others zynq boards to get uart as early as
possible.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Updating year in zynq files. Also add missing Copyright to board.c.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add low level initialization for zcu102-rev1.0.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Move generic functions to common location psu_spl_init.c. Function
declarations are added to private header.
These changes are done in connection to the fact that still files from
HDF can be copied over and compilation should pass.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Remove SPL_BUILD dependency from zynqmp.c and move it to header file.
Use only one symbol for including psu_init.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Remove functions which are no longer renerated by PCW.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

The Arasan NFC driver requires the self-init mode,
so it should select it.

Instead of having the config header define the macro,
it's cleaner to select the option at the Kconfig level.
Signed-off-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This patch corrects the ecc address calculation before updating
to ecc register. The ecc address has to be calculated based on
page, oob and ecc sizes of the device.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This patch adds support for ondie ecc. As of now
this adds support for micron parts which supports
ondie ecc.
Didn't found any better way to detect ondie ecc
support by a device except sorting out with
manufacture and device id's.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Move common part of ecc structure initialization to
arasan_nand_init() routine.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This patch adds new target which is called as mini configuration
with only emmc functionality and other required basic features enabled.
This will be used to run in system with small footprint and needs
emmc support.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This patch adds new target which is called as mini configuration
with only nand functionality and other required basic features enabled.
This will be used to run in system with small footprint and needs
nand support.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

DDR less systems are possible for configuration like mini qspi
and making DDR region as normal memory may cause speculative
access which results u-boot hang if DDR is absent. So, this
patch fixes the issue by not making DDR memory region
entry into MMU table.

Future solution is to prepare MMU table per memory node in dts instead
of hard code DDR addresses.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

psu_init() returns int which wasn't declared and checked.
The patch is fixing function declarations and code to handle return
values properly.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Remove additional spaces before comment.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Drop the space before/after '<' and '>'; and
separate the entries to be a bit more readable.
Reported-by: NJulia Cartwright <julia@ni.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

BOOTCOMMAND is composed with distro_bootcmd but this variable is not
present. Enabling distro defaults setting is fixing it.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

It will cleanup generic config and enable option to change it for every
board.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

There are two reasons for doing this change.
There is still !DM driver for xilinx soft gpio IP and especially it is
saving some space for memory constrained boards like cse (almost ~400B).
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Do not enable DM_ETH/MMC if subsystems are not enabled.
This saves memory for memory constrained boards like cse.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

There is no reason to enable BLK by default for all boards which is just
increasing memory footprint for memory contrained boards like cse.
zc770s are also saving some space.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Ethernet cable is not connected for xm011 that's why disable all
ethernet related configurations.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Wire debug console which is useful for early debugging.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

It is good to see this string to make sure that u-boot which runs on the
board is the same which should run there.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Set the 8GB PCIe High area as device memory.
Also extend the DDR High area to cover the full 32GB range.
Signed-off-by: NAnders Hedlund <anders.j.hedlund@gmail.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add check if boot_targets exists in environment and then
generate new_targets env accordingly. Performing strlen on
null address causes it to fail with exception if isolation
is enabled with DDR address zero as secure. It works with out
isolation enabled as zero is valid address but it may lead to
junk values in boot_targets.
This patch fixes the issue by checking return value of env_get
so that it generate boot_targets properly.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

These are defined, but not referenced at all.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

The patch is fixing the following Warning:
arch/arm/mach-zynq/ps7_spl_init.c:133:24: warning: comparison between
signed and unsigned integer expressions [-Wsign-compare]
    while (ioread(addr) < delay)
                        ^
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

zc770-xm011 is x8 width configuration. This FMC card has also x16
variant which requires different ps7_init configuration. This patch adds
it.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Simplify ps7_init* initialization.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Simplify ps7_init* initialization.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Simplify ps7_init* initialization.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Simplify ps7_init* initialization.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

zc770-xm011 is also added and supported. Reflect this in README.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

NAND and QSPI devices are now supported, so mark
them as such.

Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Setup proper dependency in Kconfig for SPL_CLK.
If SPL is not enabled, SPL_CLK shouldn't be selected.

Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>