- 01 10月, 2011 5 次提交
-
-
由 Ajay Bhargav 提交于
This patch enables ethernet support for Marvell GplugD board. Network related commands works. Signed-off-by: NAjay Bhargav <ajay.bhargav@einfochips.com>
-
由 Ajay Bhargav 提交于
This patch adds support for Fast Ethernet Controller driver for Armada100 series. Signed-off-by: NAjay Bhargav <ajay.bhargav@einfochips.com> Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>
-
由 Joe Hershberger 提交于
Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Sandeep Paulraj <s-paulraj@ti.com>
-
由 Ajay Bhargav 提交于
This patch adds support for generic GPIO driver framework for Marvell SoC Armada100. Signed-off-by: NAjay Bhargav <ajay.bhargav@einfochips.com>
-
由 Ajay Bhargav 提交于
This patch adds generic GPIO driver framework support for Marvell SoCs. To enable GPIO driver define CONFIG_MARVELL_GPIO and for GPIO commands define CONFIG_CMD_GPIO in your board configuration file. Signed-off-by: NAjay Bhargav <ajay.bhargav@einfochips.com>
-
- 30 9月, 2011 1 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 29 9月, 2011 4 次提交
-
-
由 Linus Walleij 提交于
Since commit d388298a by Stefano Babic this file is no longer needed so delete it. Cc: Stefano Babic <sbabic@denx.de> Cc: Loïc Minier <loic.minier@linaro.org> Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
-
由 Wolfgang Denk 提交于
This reverts commit 041c5422. The lines removed by this commit weren't redundant. The logic is (and probably should be better commented): Find the intersection of the advertised capabilities of both sides of the link (lpa). From that intersection, find the highest capability we can run at (that will be the negotiated link). Now imagine that the intersection (lpa) is (LPA_100HALF | LPA_10FULL). The code will now set phydev->speed to 100, and phydev->duplex to 1, but this link does not support 100FULL. Kudos to Andy Fleming <afleming@gmail.com> for binging this to attention and for the explanation. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
git://git.denx.de/u-boot-arm由 Wolfgang Denk 提交于
* 'master' of git://git.denx.de/u-boot-arm: ARM: remove broken "ixdp425" and "ixpdg425" boards
-
- 27 9月, 2011 1 次提交
-
-
由 Albert ARIBAUD 提交于
Signed-off-by: NAlbert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: NStefan Roese <sr@denx.de>
-
- 25 9月, 2011 1 次提交
-
-
由 Marek Vasut 提交于
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
-
- 23 9月, 2011 5 次提交
-
-
git://git.denx.de/u-boot-arm由 Wolfgang Denk 提交于
* 'master' of git://git.denx.de/u-boot-arm: OMAP3: beagle: Fix build warning in beagle.c
-
由 Vladimir Zapolskiy 提交于
This is a trivial fix in the documentation, which corrects board_init_r() source reference. Signed-off-by: NVladimir Zapolskiy <vz@mleia.com> Acked-by: NMike Frysinger <vapier@gentoo.org>
-
由 Dirk Behme 提交于
Fix build warning beagle.c:532: warning: initialization from incompatible pointer type Signed-off-by: NDirk Behme <dirk.behme@googlemail.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Koen Kooi <koen@dominion.thruhere.net> CC: Joel A Fernandes <agnel.joel@gmail.com> Cc: Greg Turner <gregturner@ti.com> CC: Sandeep Paulraj <s-paulraj@ti.com> Acked-by: NJason Kridner <jkridner@beagleboard.org>
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 22 9月, 2011 4 次提交
-
-
由 Holger Brunck 提交于
The MAC address stored in the inventory eeprom begins at offset 1. Signed-off-by: NHolger Brunck <holger.brunck@keymile.com> Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com> cc: Wolfgang Denk <wd@denx.de>
-
由 Vadim Bendebury 提交于
On some systems, we get a warning when %lu is used with size_t's, so use the correct format string. Signed-off-by: NVadim Bendebury <vbendeb@chromium.org> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
The new sanity check introduces a printf warning for some systems: eth.c:233: warning: format '%zu' expects type 'size_t', but argument 3 has type 'int' Rather than tweak the format string, use the new assert() helper instead. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
Recent commit a4814a69 cleaned up generation of asm-offsets.s for SoC dirs, but missed adding it to the ignore list which makes it show up in `git status`. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 20 9月, 2011 2 次提交
-
-
由 Wolfgang Denk 提交于
There is no code anywhere that references BOOTFLAG_* so remove these defines. Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Peter Tyser <ptyser@xes-inc.com>
-
由 Peter Korsgaard 提交于
Commit 09349866 (Put common autoload code into auto_load() function) broke handling of autoload environment variable not being set. The bootp/dhcp code will just keep on requesting IP address forever and never start TFTP download. Fix it by moving TftpStart() outside the conditional like it was before. Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk> Tested-by: NFabio Estevam <fabio.estevam@freescale.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
- 19 9月, 2011 2 次提交
-
-
由 Stefan Roese 提交于
Flush the dcache before removing the TLB with caches enabled. Otherwise this might lead to problems later on, e.g. while booting Linux (as seen on ICON-440SPe). Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Weirich, Bernhard 提交于
Change bd_t->bi_phy* arrays from 1 to 2 for PPC405EX since 405EX has 2 ethernet interfaces. Signed-off-by: NBernhard Weirich <bernhard.weirich@riedel.net> Signed-off-by: NStefan Roese <sr@denx.de>
-
- 14 9月, 2011 1 次提交
-
-
由 Sandeep Paulraj 提交于
This commit fixes a build warning in the DA830 EVM build Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 13 9月, 2011 8 次提交
-
-
由 Jason Kridner 提交于
Result of running the following command to address Wolfgang's comment about camel case: for file in `find . | grep '\.[chS]$'`; do perl -i -pe 's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done Discussion: http://patchwork.ozlabs.org/patch/84988/Signed-off-by: NJason Kridner <jkridner@beagleboard.org> Signed-off-by: NJoel A Fernandes <agnel.joel@gmail.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Aneesh V 提交于
omap4: fix pad configuration settings for SDP and Panda Signed-off-by: NAneesh V <aneesh@ti.com> Signed-off-by: NSebastien Jan <s-jan@ti.com> Signed-off-by: NDavid Anders <x0132446@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Aneesh V 提交于
Tuning some IO settings for better performance and power. And consolidate all such IO settings at one place. Signed-off-by: NAneesh V <aneesh@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Aneesh V 提交于
SDRAM init was not working on ES1.0 due to a programming error. A pointer that was passed by value to a function was set in function emif_get_device_details(), but the effect wouldn't be seen in the calling function. The issue came out while testing for ES1.0 because ES1.0 doesn't have any SDRAM chips connected to CS1 Signed-off-by: NAneesh V <aneesh@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Aneesh V 提交于
Factor out common parts from omap4_sdp4430.h and omap4_panda.h into a new file omap4_common.h Signed-off-by: NAneesh V <aneesh@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sanjeev Premi 提交于
This patch contains updates the sources in the board files to use the generic API. Signed-off-by: NSanjeev Premi <premi@ti.com>
-
由 Sanjeev Premi 提交于
This patch contains the generic changes required after change to generic API in the previous patch. Signed-off-by: NSanjeev Premi <premi@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sanjeev Premi 提交于
Convert all OMAP specific functions to use the common API definitions in include/asm/gpio.h. In the process, made few additional changes: - Use -EINVAL consistently. -1 was used in many places. - Removed one-liner static functions that were used only once. Replaced the content as necessary. - Combines implementation of functions omap_get_gpio_dataout() and omap_get_gpio_datain(). To do so, new static function _get_gpio_direction() was added. Signed-off-by: NSanjeev Premi <premi@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 12 9月, 2011 6 次提交
-
-
由 Sandeep Paulraj 提交于
This patch removes a hardcoded MAC address Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Nagabhushana Netagunte 提交于
Modify the MEMTEST start and end address. The memtest range was overlapping the CONFIG_SYS_LOAD_ADDR which causes the uImage to be corrupt.Also, modify the size for which mtest is run to 32MB from 16MB. Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: NNagabhushana Netagunte <nagabhushana.netagunte@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Nagabhushana Netagunte 提交于
Enable SPI flash boot mode in configuration file as default. With the introduction of 456MHz part, SPI operating frequency will increase and at this frequency SPI does not work correctly. Hence reduce the default SPI speed to 30MHz from 50MHz. Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: NNagabhushana Netagunte <nagabhushana.netagunte@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Nagabhushana Netagunte 提交于
Modify U-boot promt string from 'DA830-evm >' to 'U-Boot >' as there are many variants of da830 based boards which have diffrent names such as L137, AM1707 etc. Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: NNagabhushana Netagunte <nagabhushana.netagunte@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Howard D. Gray 提交于
OMAP3: Add 37xx ESx revision numbers. Signed-off-by: NMichael Jones <michael.jones@matrix-vision.de> Signed-off-by: NHoward D. Gray <howard.gray@matrix-vision.de> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Michael Jones 提交于
Signed-off-by: NMichael Jones <michael.jones@matrix-vision.de> Acked-by: NHeiko Schocher <hs@denx.de> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-