This reverts commit 39768f77.

Reson: it breaks a number of boards with embedded environment as the
code size grows in some places.

8xx was left behind when fixing up powerpc linking
scripts to support -fpic.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>

The omap24xx driver only seems to support devices that have a single subaddress
byte. With these types of devices, the first access in a bus transaction is
usually a write (writes the subaddress) followed by either a read or write to
access the devices registers.

Many such devices will respond to a read as the first access, but there are at
least some that will NACK such a read. (e.g. ADV7180.)

The probe function attempts to detect a devices ACK to a read access only and
fails to find devices that NACK a read.

This commit modifies the probe function to start a write instead. This detects
devices that respond to reads (since they must also respond to writes) as well
as those that only respond to writes. The bus is immediately set to idle after a
(N)ACK avoiding actually writing anything to the device.
Signed-off-by: NNick Thompson <nick.thompson@ge.com>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

This seems to pad to one byte longer than required
Signed-off-by: NSimon Glass <sjg@chromium.org>

Commit 6ee1416e (mtd, cfi: introduce
void flash_protect_default(void)) introduced a bug which resulted in
boards that define CONFIG_SYS_FLASH_AUTOPROTECT_LIST not compiling with
the the following errors and warning:
  ptyser@petert u-boot $ make -s xpedite520x
  Configuring for xpedite520x board...
  cfi_flash.c: In function 'flash_protect_default':
  cfi_flash.c:2118: error: 'i' undeclared (first use in this function)
  cfi_flash.c:2118: error: (Each undeclared identifier is reported only once
  cfi_flash.c:2118: error: for each function it appears in.)
  cfi_flash.c:2118: error: 'apl' undeclared (first use in this function)
  cfi_flash.c:2118: error: invalid application of 'sizeof' to incomplete type 'struct apl_s'
  cfi_flash.c: In function 'flash_init':
  cfi_flash.c:2137: warning: unused variable 'apl'
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Reported-by: NKumar Gala <galak@kernel.crashing.org>
Cc: Heiko Schocher <hs@denx.de>

Signed-off-by: NJames Kosin <jkosin@intcomgrp.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Hi Terry,

> So I guess:
> mmc_init calls mmc_send_op_cond  that set  high_capacity,
> than it calls mmc_startup, that, with MMC_CMD_SEND_CSD  command, set
> the capacity, using values in CSD register.
> So I guess that mmc_change_freq should not recalculate high_capacity.
>
> It seems better, isn't it?
>
> Regards,
> Raffaele
>

Finally I think that it is enough to apply the following patch in order
to fix the issue.

Regards,
Raffaele
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Defining CONFIG_MMC_TRACE in the include board file it is possible to activate
a tracing support.
This code helps in case of eMMC hw failure or to investigate possible eMMC
initialization issues.
Signed-off-by: NRaffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

The first SEND_OP_COND (CMD1) command added is used to ask card capabilities.
After it an AND operation is done between card capabilities and host
capabilities (at the moment only for the voltage field).
Finally the correct value is sent to the MMC, waiting that the card
exits from busy state.
Signed-off-by: NRaffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

It is recommended to check card status after these kind of commands.
This is done using CMD13 (SEND_STATUS) JEDEC command until
the card is ready.
In case of error the card status field is displayed.
Signed-off-by: NRaffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

This patch supports mmc/sd card with spi interface. It is based on
the generic mmc framework. It works with SDHC and supports multi
blocks read/write.

The crc checksum on data packet is enabled with the def,

There is a subcomamnd "mmc_spi" to setup spi bus and cs at run time.
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

These local vars need not be writable nor exported.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

As DATA_ERROR includes the value IRQSTAT_DTOE, a timeout error
would yield the first error return instead of TIMEOUT.
By swapping the test TIMEOUTs are reported as such

An alternate solution would be to remove the IRQSTAT_DTOE from the DATA_ERROR define
but as that one might be less desired I've opted for the simplest solution
Signed-off-by: NFrans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

This patch adds CONFIG_SPI_IDLE_VAL to cf_spi.c
The default setting is 0x0 to behave same as current version, in case
CONFIG_SPI_MMC is set, the value is set to 0xFFFF (all ones). In either
case, the value can be overwritten by board configuration.
Signed-off-by: NWolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

The maximum blocks value was hardcoded to 65535 due to a 16 bit
register length.  The value can change for different platforms.
This patch makes the default the current value of 65535, but it
is configurable for other platforms.
Signed-off-by: NMatt Waddel <matt.waddel@linaro.org>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

The README files are totally out-of-date to the point where they do more
harm than good
Signed-off-by: NGraeme Russ <graeme.russ@gmail.com>

Partial linking allows weak functions to be overridden in files containing
only one function. Moving the sc520 override of reset_cpu gets rid of an
ugly #ifdef
Signed-off-by: NGraeme Russ <graeme.russ@gmail.com>

Signed-off-by: NGraeme Russ <graeme.russ@gmail.com>

Make the copyright notices in the x86 files consistent and update them with
proper attributions for recent updates

Also fix a few comment style/accuracy and whitespace/blank line issues
Signed-off-by: NGraeme Russ <graeme.russ@gmail.com>

By including <config.h> in the ld script, CONFIG_SYS_MONITOR_LEN (defined
in the boards config file) can be used in lieu of FLASH_SIZE (defined in
the board specific config.mk)

As this is the last remaining entry in the board specific config.mk, this
file can now be removed
Signed-off-by: NGraeme Russ <graeme.russ@gmail.com>

CONFIG_ENV_SIZE = CONFIG_ENV_SECT_SIZE = 128kB but CONFIG_SYS_STACK_SIZE
is only 32kB resulting in saveenv causing a stack overflow and crashing
U-Boot. Resolve by reducing CONFIG_ENV_SIZE to 4kB

Also fix up CONFIG_SYS_MALLOC_LEN to correctly use environment sector
size and add some comments to the memory organisation configuration
Signed-off-by: NGraeme Russ <graeme.russ@gmail.com>

Fixed a bug wherein SD version 1.0 cards were not configured for 4-bit mode
Signed-off-by: NAlagu Sankar <alagusankar@embwise.com>

If the param pass to get_dev is not the one defined in the block_drvr,
it could make uboot becomes unstable, for it would continue run after
search complete the block_drvr table.
Signed-off-by: NLei Wen <leiwen@marvell.com>

* The sector size for SPI-dataflash (like AT45 flashes) are not always
  a power-of-2. So, the sector calculations are rewritten such that it
  works for either power-of-2 as any size sectors.
* Make the flash sector size optional in case it is the same value as
  the environment size.
Signed-off-by: NRemy Bohmer <linux@bohmer.net>

Signed-off-by: NWolfgang Denk <wd@denx.de>

1. Move header to include/faraday
2. Fix include path in ftwdt010_wdt.c
3. Fix function prototype and declaration to
  - ftwdt010_wdt_settimeout
  - ftwdt010_wdt_reset
  - ftwdt010_wdt_disable
4. Add "#if definde (CONFIG_HW_WATCHDOG)" let user have flexibilty
  to choose which better to his product.
Signed-off-by: NMacpaul Lin <macpaul@andestech.com>

This patch fixes following warning message:

---8<---
cmd_bdinfo.c:458: warning: initialization from incompatible pointer type
--->8---

There was a prototype change in 54841ab5 for
argv[] pointer type to const. This change was not made for AVR32 cause this
code came in later by a merge.
Signed-off-by: NAndreas Bießmann <biessmann@corscience.de>

This patch fixes warnings in MAKEALL for avr32:

---8<---
cmd_nvedit.c: In function 'do_env_export':
cmd_nvedit.c:663: warning: format '%zX' expects type 'size_t', but argument 3 has type 'ssize_t'
--->8---
Signed-off-by: NAndreas Biemann <biessmann@corscience.de>

Rename STANDALONE_LOAD_ADDR into CONFIG_STANDALONE_LOAD_ADDR
and allow that the architecture-specific default value gets
overwritten by defining the value in the board header file.
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Tsi Chung Liew <tsi-chung.liew@freescale.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

"make tools-all" should allow building tools such as mkimage and the new
imximage without any config, but imximage.c currently fails to build
with:
imximage.h:27:20: error: config.h: No such file or directory

config.h is not needed in imximage.h nor in imximage.c, and imximage.h
is only included from imximage.c, so drop this include to fix the build.
Signed-off-by: NLoc Minier <loic.minier@linaro.org>

Signed-off-by: NLoc Minier <loic.minier@linaro.org>

Signed-off-by: NCatalin Radu <Catalin@VirtualMetrix.com>