Full conversion to dm for all boards, legacy code removed.
Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>

Add ColdFire fec to Kconfig.
Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>

Add architecture-related code for dm fec support.
Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>

Remove unneeded fec-related defines after fec moved as dm.
Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>

Add dm eth config options for all involved ColdFire-based boards.
Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>

Add ethernet controller overrides for all involved boards.
Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>

Add basic ethernet controller devicetree nodes for all ColdFire
families.
Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>

- A small PR with MC8309 fixes from Rasmus.

dm: Increased separation of ofdata_to_platdata() and probe methods

- DFU updates

Pull request for UEFI sub-system for efi-2020-04-rc1

This pull request provides:

* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables

UniPhier SoC updates for v2020.04

- add pinmux nodes for I2C ch5, ch6

- enable SPI driver and command

```------------------------------------------------------------------
Add i.MX8MP SoC and EVK board
Update README for i.MX8MN EVK and fix mmc env
Add pca9450 driver
```

-----------------------------------------------------------------

Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/634211885

- Khadas VIM3L based on Amlogic S905D3 support
- Various fixups for amlogic boards
- Unnecessary header includes drop into video/meson

- DT overlay support in FIT images in SPL
- remoteproc update
- Assorted SATA fixes
- Other assorted fixes

Compile drivers/spi/uniphier_spi.c and cmd/spi.c
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

The next generation SoC can connect on-board slave devices via
I2C ch5 and ch6.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

In the initialization of sata driver, we want to initialize all port
 probes, Therefore, any detection failure between of them should continue
 initialization by skipping the current port instead of exit.
Signed-off-by: NPeng Ma <peng.ma@nxp.com>

In the initialization of sata driver, we want to initialize all port
 probes, Therefore, any detection failure between of them should continue
 initialization by skipping the current port instead of exit.
Signed-off-by: NPeng Ma <peng.ma@nxp.com>

As previous CONFIG_SYS_UBOOT_START is now set by default to
CONFIG_SYS_TEXT_BASE when not defined, CONFIG_SYS_UBOOT_START
can be removed from include/configs board files.
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Acked-by: NLukasz Majewski <lukma@denx.de>

This patches restores boot on boards which rely on
CONFIG_SYS_UBOOT_START equal to CONFIG_SYS_TEXT_BASE when using SPL

Fixes: d3e97b53 ("spl: fix entry_point equal to load_addr")
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Per Enea OSE documentation, it supports some classes of ARM, PowerPC and
X86.  Limit the option to those platforms.
Signed-off-by: NTom Rini <trini@konsulko.com>

enable CONFIG_CMD_ERASEENV to make it easy to erase env.
Use savedefconfig to generate new defconfig.
Reviewed-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Add board_mmc_get_env_dev, otherwise,
Loading Environment from MMC...
MMC Device 0 not found
*** Warning - No MMC card found, using default environment
Reviewed-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Add a README for users to build a workable image.
Reviewed-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Add basic i.MX8MP EVK board support

U-Boot SPL 2020.01-rc4-00388-gb1bf40c0ae-dirty (Dec 30 2019 - 17:55:33 +0800)
power_pca9450b_init
DDRINFO: start DRAM init
DDRINFO:ddrphy calibration done
DDRINFO: ddrmix config done
Normal Boot
Failed to find clock node. Check device tree
WDT:   Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0

U-Boot 2020.01-rc4-00388-gb1bf40c0ae-dirty (Dec 30 2019 - 17:55:33 +0800)

CPU:   Freescale i.MX8MP rev1.0 at 1000 MHz
Reset cause: POR
Model: NXP i.MX8MPlus EVK board
DRAM:  6 GiB
MMC:   FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0
u-boot=> mmc list
FSL_SDHC: 1 (SD)
FSL_SDHC: 2
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Add imximage-8mp-lpddr4.cfg for imximage usage, almost same
as i.MX8MN ddr4 cfg, but with different ddr firmware
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Add i.MX8MP clk driver for i.MX8MP CLK driver model usage
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Add imx_clk_mux2_flags which will be used by i.MX8MP
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

The drivers/clk/imx/*.c are used for CLK dm case, the
clock_imx8mm.c is used for non CLK dm case, let's split
it. Sometimes it is hard to enable CLK dm in SPL stage,
considering code size, malloc size requirement, the splittion
will make it easy to use non CLK dm in SPL stage.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

i.MX8MP ROM support ROMAPI as i.MX8MN, so make
SPL_IMX_ROMAPI_LOADADDR visible to i.MX8MP
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

i.MX8MP does not have LVTTL, it has a PE property
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Add pin header file for i.MX8MP
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

PCA9450 PMIC series is used to support iMX8MM (PCA9450A) and
iMX8MN (PCA9450B). Add the PMIC driver for both PCA9450A and PCA9450B.
Signed-off-by: NRobin Gong <yibin.gong@nxp.com>
Signed-off-by: NYe Li <ye.li@nxp.com>
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

The i.MX8M Plus Media Applications Processor is part of the growing
mScale family targeting the consumer and industrial market. It brings
an effective Machine Learning and AI accelerator that enables a new
class of applications. It is built in Samsung 14LPP to achieve both
high performance and low power consumption and relies on a powerful
fully coherent core complex based on a quad core ARM Cortex-A53 cluster
and Cortex-M7 low-power coprocessor, audio digital signal processor,
machine learning and graphics accelerators.

Add the basic dtsi support for i.MX8MP.

Patch from Anson Huang for Kernel
https://patchwork.kernel.org/patch/11310915/Signed-off-by: NPeng Fan <peng.fan@nxp.com>

We will generate DRAM 4000MT/s as default for i.MX8MP.
So need DRAM PLL to generate 1000Mhz clock to DDR PHY and controller.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

i.MX8MP use similar ocotp as i.MX8MN, but has changed fuse banks
and ctrl register bit definitions, so update to reflect that.
Reviewed-by: NYe Li <ye.li@nxp.com>
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Add i.MX8MP compatible to let the pinctrl driver could support
i.MX8MP.
Reviewed-by: NYe Li <ye.li@nxp.com>
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

4000MTS DDR needs 1GHz fracpll, so add the entry
Signed-off-by: NPeng Fan <peng.fan@nxp.com>