- 28 4月, 2011 12 次提交
-
-
由 Fabio Estevam 提交于
Commit 5d2c154 (IMX: MX31: Cleanup include files and drop nasty #ifdef in drivers) renamed mx31-imx-regs.h to imx-regs.h. Change the file label accordingly. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Acked-by: NDetlev Zundel <dzu@denx.de>
-
由 Fabio Estevam 提交于
Use the same method of the Linux kernel to print the MX31 silicon version on boot. Tested on a MX31PDK with a 2.0 silicon, where it shows: CPU: Freescale i.MX31 rev 2.0 at 531 MHz Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Stefano Babic 提交于
As exception among the i.MX processors, the i.MX31 has headers without general names (mx31-regs.h, mx31.h instead of imx-regs.h and clock.h). This requires several nasty #ifdef in the drivers to include the correct header. The patch cleans up the driver and renames the header files as for the other i.MX processors. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Liu Hui-R64343 提交于
device tree for uboot arm support has already been enabled in the master branch. This patch enable device tree support for mx51/53 evk board for DT test. Signed-off-by: NJason Liu <r64343@freescale.com>
-
由 Liu Hui-R64343 提交于
The config.mk file in board directory is now obsolete and should be removed. Add option for the IMX image into boards.cfg Signed-off-by: NJason Liu <r64343@freescale.com>
-
由 Fabio Estevam 提交于
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Stefano Babic 提交于
Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Stefano Babic 提交于
The patch add CONFIG_HW_WATCHDOG to be used with the internal watchdog timer of the MX31 processor. Two function are exported for the board maintainers: mxc_hw_watchdog_enable mxc_hw_watchdog_reset The board maintainer can decide to use mxc_hw_watchdog_reset as hw_watchdog_reset, or to implement his own function to reset the watchdog. The watchdog timer can be configured with CONFIG_SYS_WD_TIMER_SECS (value in seconds). The MX31 allows values between 0.5 (CONFIG_SYS_WD_TIMER_SECS = 0) and 128 seconds. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Stefano Babic 提交于
The config.mk file in board directory is now obsolete and should be removed. Add option for the IMX image into boards.cfg Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Stefano Babic 提交于
config.mk in board directory is obsolete and should be removed. The patch allows to get rid of own config.mk adding the imximage.cfg file to the options in the boards.cfg Signed-off-by: NStefano Babic <sbabic@denx.de>
-
- 26 4月, 2011 3 次提交
-
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de> Acked-by: NDetlev Zundel <dzu@denx.de>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de> Acked-by: NDetlev Zundel <dzu@denx.de>
-
由 Loïc Minier 提交于
Signed-off-by: NLoc Minier <loic.minier@linaro.org>
-
- 25 4月, 2011 3 次提交
-
-
-
-
由 Joakim Tjernlund 提交于
Two linker scripts for 8xx was missed. Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
-
- 21 4月, 2011 22 次提交
-
-
由 Aaron Williams 提交于
I ran into a problem where the reset was failing except when I enabled debugging support. After talking with Garret Swalling at Spansion I was told that the GL-N series of devices require a 500ns wait for the reset to complete. The below patch adds a 1us delay after all reset commands. -Aaron Williams Signed-off-by: NAaron Williams <aaron.williams@caviumnetworks.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Heiko Schocher 提交于
tested on the a4m072 board with a S29GL512P flash. flinfo without this patch Bank # 1: CFI conformant flash (16 x 16) Size: 32 MB in 256 Sectors AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E Erase timeout: 16384 ms, write timeout: 2 ms Buffer write timeout: 5 ms, buffer size: 32 bytes [...] flinfo with this patch Bank # 1: CFI conformant flash (16 x 16) Size: 32 MB in 256 Sectors AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E2301 Erase timeout: 16384 ms, write timeout: 2 ms Buffer write timeout: 5 ms, buffer size: 32 bytes [...] Signed-off-by: NHeiko Schocher <hs@denx.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Mike Frysinger 提交于
The M29W800DT parts also report their geometry with the sector layout reversed. So add that ID to the flash_fixup_stm function. Otherwise, we get: bfin> flinfo Bank # 1: CFI conformant FLASH (16 x 16) Size: 1 MB in 19 Sectors AMD Standard command set, Manufacturer ID: 0x20, Device ID: 0x22D7 Erase timeout: 8192 ms, write timeout: 1 ms Sector Start Addresses: 20000000 20004000 20006000 20008000 20010000 20020000 20030000 20040000 20050000 20060000 20070000 20080000 20090000 200A0000 200B0000 200C0000 200D0000 200E0000 200F0000 Reported-by: NJianxi Fu <fujianxi@gmail.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Dirk Eibach 提交于
Use CONFIG_AUTOBOOT_KEYED on dlvision-10g so that booting can only be stopped with well defined keypresses. Signed-off-by: NDirk Eibach <eibach@gdsys.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Dirk Eibach 提交于
Signed-off-by: NDirk Eibach <eibach@gdsys.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Dirk Eibach 提交于
Signed-off-by: NDirk Eibach <eibach@gdsys.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Dirk Eibach 提交于
Signed-off-by: NDirk Eibach <eibach@gdsys.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Dirk Eibach 提交于
Signed-off-by: NDirk Eibach <eibach@gdsys.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Dirk Eibach 提交于
Signed-off-by: NDirk Eibach <eibach@gdsys.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Dirk Eibach 提交于
Signed-off-by: NDirk Eibach <eibach@gdsys.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Dirk Eibach 提交于
Signed-off-by: NDirk Eibach <eibach@gdsys.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Ricardo Ribalda Delgado 提交于
Old address of RESET_VECTOR were overwritten by the bss sector, making impossible its run from xmd. Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Jon Povey 提交于
This fixes two bugs with comparison of redundant environment flags on read. flag0 and flag1 in fw_env_open() were declared signed instead of unsigned char breaking BOOLEAN mode "== 0xFF" tests and in INCREMENTAL mode the wrong environment would be chosen where the flag values are 127 and 128 (either way round). With both flags over 128, both signs flipped and the logic worked by happy accident. Also there was a logic bug in the INCREMENTAL test (after signedness was fixed) in the case flag0=0, flag1=255, env 1 would be incorrectly chosen. Fix both of these. Signed-off-by: NJon Povey <jon.povey@racelogic.co.uk>
-
-
-
-
-
-
-
由 Wolfgang Denk 提交于
This reverts commit 39768f77. Reson: it breaks a number of boards with embedded environment as the code size grows in some places.
-
由 Andy Fleming 提交于
The new mdio command doesn't have all of the features of the mii command, but it provides the necessary read/write primitives, and allows users to interact with 10G PHYs, and other PHYs which use Clause 45 of 802.3. This means that the mdio command requires a "Device Address" argument, though for clause 22 PHYs, the argument can be "-". Signed-off-by: NAndy Fleming <afleming@freescale.com> Acked-by: NDetlev Zundel <dzu@denx.de>
-
由 Andy Fleming 提交于
The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum. This meant that drivers which used fsl_phy_enet_if to deal with PHY interfaces would have to convert between the two (or we would have to have them mirror each other, and deal with the ensuing maintenance headache). Instead, we switch all clients of fsl_phy_enet_if over to phy_interface_t, which should become the standard, anyway. Signed-off-by: NAndy Fleming <afleming@freescale.com> Acked-by: NDetlev Zundel <dzu@denx.de>
-