The function fdt_fixup_dr_usb is specific to fsl/nxp. So,
make the function name explicit and rename fdt_fixup_dr_usb
into fsl_fdt_fixup_dr_usb.
Signed-off-by: NSriram Dash <sriram.dash@nxp.com>

Since commit aa7a6487
("net: Stop including NFS overhead in defragment max") the following
has been reproducibly observed while trying to transfer data over TFTP:

Load address: 0x80408000
Loading: EHCI timed out on TD - token=0x8008d80
T EHCI timed out on TD - token=0x88008d80
Rx: failed to receive: -5

This patch fixes this by lowering our TFTP block size to be within the
standard maximal de-fragmentation aka IP packet size again.
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>

Enable USB driver model for Toradex Colibri Vybrid modules.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>

Enable USB device tree node for Toradex Colibri Vybrid module.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>

Add device tree node for USB peripheral on Vybrid.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>

Add driver model support for Vybrid USB driver.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>

Without this, if g_dnl_register() fails, DFU code continues on
blindly and crashes. This fix makes it simply print an error
message instead.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
[l.majewski@samsung.com - some manual tweaks needed]

This patch enables the SPL-DFU support for
dra7x platform.
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

This patch enables the DFU boot mode support
for dra7x platform.
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Adding support functions to run dfu spl commands.
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

The cmd_dfu functionality is been used by both SPL and
u-boot, saperating the core dfu functionality moving
it to common/dfu.c.
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Traditionally the DFU support is available only
as part 2nd stage boot loader(u-boot) and DFU
is not supported in SPL.

The SPL-DFU feature is useful for boards which
does not have MMC/SD, ethernet boot mechanism
to boot the board and only has USB inteface.

This patch add DFU support in SPL with RAM
memory device support to load and execute u-boot.
And then leverage full functionality DFU in
u-boot to flash boot inital binary images to
factory or bare-metal boards to memory devices
like SPI, eMMC, MMC/SD card using USB interface.

This SPL-DFU support can be enabled through
Menuconfig->Boot Images->Enable SPL-DFU support
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

This is required for better performance, and performs below tuning:
1. Enable burst length set, and define it as 4/8/16.
2. Set burst request limit to 16 requests.
Signed-off-by: NRajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: NSriram Dash <sriram.dash@nxp.com>

Since commit aa7a6487
("net: Stop including NFS overhead in defragment max") the following
has been reproducibly observed while trying to transfer data over TFTP:

Load address: 0x80408000
Loading: EHCI timed out on TD - token=0x8008d80
T EHCI timed out on TD - token=0x88008d80
Rx: failed to receive: -5

This patch fixes this by upping our maximal de-fragmentation aka IP
packet size again.
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>

Commit 14727120 ("net: asix: fix operation without eeprom")
added a special handling for ASIX 88772B that enable another
type of header. This break the driver in DM mode as the extra handling
needed in the receive path is missing.

However this new header mode is not required and only seems to
increase the code complexity, so this patch revert this part of
commit 14727120.

This also reverts commit 41d1258a
("net: asix: Fix AX88772B when used with DriverModel") of late.

Fixes: 14727120 ("net: asix: fix operation without eeprom")
Signed-off-by: NAlban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>

trini: Drop local memset() from
examples/standalone/mem_to_mem_idma2intr.c
Signed-off-by: NTom Rini <trini@konsulko.com>

move the UBI config options into Kconfig.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NAndrew F. Davis <afd@ti.com>
Reviewed by: Evgeni Dobrev <evgeni at studio-punkt.com>

Instead of using CONFIG_* name space, rename these two macros to
SYS_FSL_* space.
Signed-off-by: NYork Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Move this option to Kconfig and clean up existing uses.
Signed-off-by: NYork Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

It should be EMMC_BOOT instead of CONFIG_EMMC_BOOT.
Signed-off-by: NYork Sun <york.sun@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Move this option to Kconfig and clean up existing uses.
Signed-off-by: NYork Sun <york.sun@nxp.com>
CC: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>

Move this config to Kconfig option and clean up existing uses.
Signed-off-by: NYork Sun <york.sun@nxp.com>
CC: Calvin Johnson <calvin.johnson@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Instead of using multiple macros, a data structure is used to pass
board-specific parameters to MMDC DDR driver.
Signed-off-by: NYork Sun <york.sun@nxp.com>
CC: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Move this option to Kconfig and clean up existing uses.
Signed-off-by: NYork Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

By adding the "marvell,mv78230-i2c" compatible property, we can enable
this I2C driver to support these new ARM64 chips as well.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Heiko Schocher <hs@denx.de>

The I2C bus will get stuck when reading 0 byte. So we add validation of
the read length in i2c_read(). This issue only occurs on read operation.
Signed-off-by: Njinghua <jinghua@marvell.com>
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>

This patch adds runtime speed configuration to the mv_i2c driver.
Currently standard (max 100kHz) and fast mode (max 400kHz) are
supported.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>

Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>

To prepare for the DM conversion, we add a layer of compatibility
functions to be used by both the legacy and the DM functions.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>

CONFIG_HARD_I2C is not needed, lets remove it.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>

Some mostly indentation coding style cleanups. Also, move this driver
to use debug() for debug output.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>

Update amcore board to use dm serial driver.
Signed-off-by: NAngelo Dureghello <angelo@sysam.it>
---
Changes for v2:
- None

Add some useful update scripts.
Signed-off-by: NAngelo Dureghello <angelo@sysam.it>
---
Changes for v.2:
- Fix syntax error on upgrade_jffs2 script

Enable the NAND interface on this board.
Signed-off-by: NChris Packham <judge.packham@gmail.com>
Signed-off-by: NStefan Roese <sr@denx.de>

This board is a plug in card for Marvell's switch system development
kits. Form-factor aside it is similar to the DB-88F6820-GP with the
following differences.
- TCLK is 200MHz
- SPI1 is used
- No SATA
- No MMC
- NAND flash
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NChris Packham <judge.packham@gmail.com>
Signed-off-by: NStefan Roese <sr@denx.de>

88F6820 is a specific Armada-38x chip that is used on the DB-88F6820-GP
board. Rather than having DB_88F6820_GP and TARGET_DB_88F6820_GP which
selects the former. Rename DB_88F6820_GP to 88F6820 so that other boards
using the 88F6820 can be added.

Stefan:
Change 88F6820 for clearfog as well.
Signed-off-by: NChris Packham <judge.packham@gmail.com>
Signed-off-by: NStefan Roese <sr@denx.de>

Use a board-specific board_sat_r_get() function to configure the board
for PCIe 2.0 capability (e.g. 5GB/s link speed). Otherwise the default
of 2.5GB/s will be established.
Signed-off-by: NStefan Roese <sr@denx.de>

This driver is designed in a generic manner, so resets should be
handled generically as well.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

My motivation for this patch is to make reset control handling
optional for generic drivers.

I want to add reset control to drivers/usb/host/ehci-generic.c,
but it is used by several platforms, some will implement a reset
controller driver, some will not.

Add no-op stubs in order to avoid link error for drivers that
implement reset controlling, but still it is optional.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>