- 30 1月, 2018 18 次提交
-
-
由 Michal Simek 提交于
BOOTCOMMAND is composed with distro_bootcmd but this variable is not present. Enabling distro defaults setting is fixing it. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
It will cleanup generic config and enable option to change it for every board. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
There are two reasons for doing this change. There is still !DM driver for xilinx soft gpio IP and especially it is saving some space for memory constrained boards like cse (almost ~400B). Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Do not enable DM_ETH/MMC if subsystems are not enabled. This saves memory for memory constrained boards like cse. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
There is no reason to enable BLK by default for all boards which is just increasing memory footprint for memory contrained boards like cse. zc770s are also saving some space. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Ethernet cable is not connected for xm011 that's why disable all ethernet related configurations. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Wire debug console which is useful for early debugging. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
It is good to see this string to make sure that u-boot which runs on the board is the same which should run there. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Anders Hedlund 提交于
Set the 8GB PCIe High area as device memory. Also extend the DDR High area to cover the full 32GB range. Signed-off-by: NAnders Hedlund <anders.j.hedlund@gmail.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
Add check if boot_targets exists in environment and then generate new_targets env accordingly. Performing strlen on null address causes it to fail with exception if isolation is enabled with DDR address zero as secure. It works with out isolation enabled as zero is valid address but it may lead to junk values in boot_targets. This patch fixes the issue by checking return value of env_get so that it generate boot_targets properly. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Masahiro Yamada 提交于
These are defined, but not referenced at all. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
The patch is fixing the following Warning: arch/arm/mach-zynq/ps7_spl_init.c:133:24: warning: comparison between signed and unsigned integer expressions [-Wsign-compare] while (ioread(addr) < delay) ^ Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
zc770-xm011 is x8 width configuration. This FMC card has also x16 variant which requires different ps7_init configuration. This patch adds it. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Simplify ps7_init* initialization. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Simplify ps7_init* initialization. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Simplify ps7_init* initialization. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Simplify ps7_init* initialization. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
zc770-xm011 is also added and supported. Reflect this in README. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 24 1月, 2018 2 次提交
-
-
由 Ezequiel Garcia 提交于
NAND and QSPI devices are now supported, so mark them as such. Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Ezequiel Garcia 提交于
Setup proper dependency in Kconfig for SPL_CLK. If SPL is not enabled, SPL_CLK shouldn't be selected. Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 17 1月, 2018 1 次提交
-
-
由 Tom Rini 提交于
In some cases when "more" is told to page a given file it will prepend the output with: :::::::::::::: /PATH/TO/THE/FILE :::::::::::::: And when this happens the output will not match the expected length. Further, if we use a different pager we will instead fail the coverage tests as we will not have 100% coverage. Update the help test to remove the string in question. Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 16 1月, 2018 19 次提交
-
-
-
-
由 Peng Fan 提交于
The operation should be OR, not BIT OR. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Heiko Schocher <hs@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
Modify the lpi2c alias seq number to align with device. Then no need to add 4 to get the device index. Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
The number 4 is dedicated on i.MX7ULP, but lpi2c will be reused on i.MX8, 4 is not valid. The seq number could be configured by alias node. The following patch will use i2c4 as the begin for i.MX7ULP. Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Simon Glass 提交于
Set this to our own device-tree compiler since we know it is new enough to run the tests. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
The system device-tree compiler may not be new enough to run the tests we use in U-Boot (e.g. with binman). Allow use of a DTC environment variable to point to the correct dtc. If not defined, the dtc on the default PATH is used. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Andre Przywara 提交于
The DT spec demands a unit-address in a node name to match the "reg" property in that node. Newer dtc versions will throw warnings if this is not the case. Remove the unit address from the config node name when U-Boot deals with secure firmware FIT images. Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
-
由 Andre Przywara 提交于
The DT spec demands a unit-address in a node name to match the "reg" property in that node. Newer dtc versions will throw warnings if this is not the case. Correct the generated unit names when U-Boot's mkimage creates a FIT image. Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
-
由 Andre Przywara 提交于
The DT spec demands a unit-address in a node name to match the "reg" property in that node. Newer dtc versions will throw warnings if this is not the case. Adjust the FIT build script for 64-bit Allwinner boards to remove the bogus addresses from the node names and avoid the warnings. This avoids a warning with recent versions of the dtc tool. Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
-
由 Andre Przywara 提交于
The DT spec demands a unit-address in a node name to match the "reg" property in that node. Newer dtc versions will throw warnings if this is not the case. Fix all occurences in the tree where node names were mentioned in comments, to not give bad examples to the reader. Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
-
由 Andre Przywara 提交于
The DT spec demands a unit-address in a node name to match the "reg" property in that node. Newer dtc versions will throw warnings if this is not the case. Fix all occurences in various documentation files where this was not observed, to not give bad examples to the reader. Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
-
由 Andre Przywara 提交于
The DT spec demands a unit-address of a node name to match the "reg" property in that node. Newer dtc versions will throw warnings if this is not the case. Fix all occurences in the FIT image example files where this was not observed, to not give bad examples to the reader. Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
-
由 Andre Przywara 提交于
The DT spec demands a unit-address in a node name to match the "reg" property in that node. Newer dtc versions will throw warnings if this is not the case. Fix all occurences in the FIT image documentation files where this was not observed, to not give bad examples to the reader. Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
-
由 Simon Glass 提交于
Binman has 100% test coverage for the code as it is at present. To encourage it to stay that way, run the code-coverage test as part of the normal U-Boot tests. This is RFC because it requires the Python code coverage tools to be available. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Run tests for the Python tools used by U-Boot. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Update the test script to run the dtoc tests also. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Update the test script to run the buildman tests also. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Update the test script to run the patman tests also. Signed-off-by: NSimon Glass <sjg@chromium.org>
-