Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR,
CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and
move these entries to defconfigs.
Signed-off-by: NRajesh Bhagat <rajesh.bhagat@nxp.com>
[Rebased]
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_NAND_FSL_ELBC
   CONFIG_NAND_FSL_IFC

Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SYS_NAND_ONFI_DETECTION
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SYS_MALLOC_LEN
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NSean Anderson <seanga2@gmail.com>
Reviewed-by: NRick Chen <rick@andestech.com>

- Guard most of the options in drivers/ddr/fsl/Kconfig with
  SYS_FSL_DDR || SYS_FSL_MMDC.
- Migrate FSL_DMA, DDR_ECC, DDR_ECC_CMD, and ECC_INIT_VIA_DDRCONTROLLER
  to Kconfig.
- Clean up the logic for including the DDR_ECC_CMD code.
Signed-off-by: NTom Rini <trini@konsulko.com>

As this symbol can either be a fixed value or the function
get_board_ddr_clk, migration is tricky.  Introduce a choice of DYNAMIC
or STATIC_DDR_CLK_FREQ.  If DYNAMIC, we continue to use the board
defined get_board_ddr_clk function.  If STATIC, set CONFIG_DDR_CLK_FREQ
to that value and now include/clock_legacy.h contains the function
prototype or defines get_board_ddr_clk() to that static value.  Update
callers to test for DYNAMIC or STATIC.
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_I2C_SET_DEFAULT_BUS_NUM
   CONFIG_I2C_DEFAULT_BUS_NUMBER
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SYS_I2C_MXC
   CONFIG_SYS_I2C_MXC_I2C1
   CONFIG_SYS_I2C_MXC_I2C2
   CONFIG_SYS_I2C_MXC_I2C3
   CONFIG_SYS_I2C_MXC_I2C4
Signed-off-by: NTom Rini <trini@konsulko.com>

First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig.  Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL.  Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support.  Convert all of the existing users to
one or more symbols.
Signed-off-by: NTom Rini <trini@konsulko.com>

- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
  based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
  CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
  CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
  to Kconfig.  We move these symbols around a bit and add appropriate
  dependencies to them.  In some cases, we now add a correct default value
  as well.
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: NStephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Enable CMD_GPIO for board ls1043aqds
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Enable CONFIG_NVME and CONFIG_CMD_NVME for Layerscape
platforms
Signed-off-by: NWasim Khan <wasim.khan@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_ENV_OVERWRITE
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Add Root Complex and Endpoint mode specific config entries, such that
it's feasible to enable the RC and/or EP mode driver indepently.
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_PHYLIB
   CONFIG_BITBANGMII
   CONFIG_MV88E6352_SWITCH
   CONFIG_MV88E61XX_SWITCH
   CONFIG_PHYLIB_10G
   CONFIG_PHY_AQUANTIA
   CONFIG_PHY_ATHEROS
   CONFIG_PHY_BROADCOM
   CONFIG_PHY_CORTINA
   CONFIG_PHY_DAVICOM
   CONFIG_PHY_ET1011C
   CONFIG_PHY_LXT
   CONFIG_PHY_MARVELL
   CONFIG_PHY_MICREL
   CONFIG_PHY_NATSEMI
   CONFIG_PHY_REALTEK
   CONFIG_RTL8211X_PHY_FORCE_MASTER
   CONFIG_PHY_SMSC
   CONFIG_PHY_TERANETICS
   CONFIG_PHY_TI
   CONFIG_PHY_VITESSE
   CONFIG_PHY_XILINX
Signed-off-by: NTom Rini <trini@konsulko.com>

This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1043A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Both symbols must be enabled when there is a raw NAND driver
selected. Also enable them when CONFIG_CMD_NAND is selected to avoid
breaking things when we'll further rework the MTD dependency
description.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@bootlin.com>
[trini: Rebase and migrate a few more boards here]
Signed-off-by: NTom Rini <trini@konsulko.com>

- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

Move the main symbol for Freescale Fman Ethernet controller option to
Kconfig.  Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and
rename the SPIFLASH one to follow the same format as all of the others.
To do this fully we need to migrate CONFIG_QC, do so.
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
  CONFIG_SF_DEFAULT_BUS
  CONFIG_SF_DEFAULT_CS
  CONFIG_SF_DEFAULT_MODE
  CONFIG_SF_DEFAULT_SPEED

I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>

EFI applications need bounce buffers to work properly on these
platforms.
Signed-off-by: NMian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls1043aqds
defconfigs that missing one of them or more.
Support sata for all ls1043aqds defconfigs
Signed-off-by: NPeng Ma <peng.ma@nxp.com>
Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_FLASH_CFI_DRIVER
   CONFIG_SYS_FLASH_USE_BUFFER_WRITE
   CONFIG_FLASH_CFI_MTD
   CONFIG_SYS_FLASH_PROTECTION
   CONFIG_SYS_FLASH_CFI
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: NTom Rini <trini@konsulko.com>