cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

 # CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>

These are declared in Kconfig, but some #defines have crept in.

CONFIG_FPGA
CONFIG_FPGA_ALTERA
CONFIG_FPGA_CYCLON2
CONFIG_FPGA_SOCFPGA
CONFIG_FPGA_XILINX
CONFIG_FPGA_ZYNQMPPL
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>

In most places in the code we cast this to an unsigned long, but in one
place we cast to an unsigned int.  For consistency and to fix a warning
on 64bit targets, always cast this to unsigned long.  For the long term
we should however change the declaration of dma_buf.

Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: NLukasz Majewski <lukma@denx.de>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NTom Rini <trini@konsulko.com>

Update email address.
Signed-off-by: NJorge Ramirez-Ortiz <jramirez@baylibre.com>

This forces all compiler warnings to be treated as errors.
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>

The build script should not manipulate shell flags (especially '-e').
A non-zero exit value can also be catched with 'cmd || ret=$?'.
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Add a new option '-E' for treating all compiler warnings as errors.
Eventually this will pass 'KCFLAGS=-Werror' to Kbuild.
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>

Probably not all users are aware of this possibility, thus add a
pointer to the README. Also add a useful example.
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>

Free Electrons is no more and is now known as Bootlin, change my email
address accordingly.
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>

This patch adds a sec_init call into arch_misc_init(). Doing so in
conjunction with the patch "drivers/crypto/fsl: assign job-rings to
non-TrustZone" enables use of the CAAM in Linux when OPTEE/TrustZone is
active.

u-boot will initialise the RNG and assign ownership of the job-ring
registers to a non-TrustZone context. With recent changes by Lukas Auer to
fully initialize the RNG in sec_init() this means that u-boot will hand-off
the CAAM in a state that Linux then can use the CAAM without touching the
reserved DECO registers.

This change is safe both for the OPTEE/TrustZone boot path and the regular
non-OPTEE/TrustZone boot path.
Signed-off-by: NBryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marco Franchi <marco.franchi@nxp.com>
Cc: Vanessa Maegima <vanessa.maegima@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: NLukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>

After enabling TrustZone various parts of the CAAM silicon become
inaccessible to non TrustZone contexts. The job-ring registers are designed
to allow non TrustZone contexts like Linux to still submit jobs to CAAM
even after TrustZone has been enabled.

The default job-ring permissions after the BootROM look like this for
job-ring zero.

ms=0x00008001 ls=0x00008001

The MS field is JRaMIDR_MS (job ring MID most significant).

Referring to "Security Reference Manual for i.MX 7Dual and 7Solo
Applications Processors, Rev. 0, 03/2017" section 8.10.4 we see that
JROWN_NS controls whether or not a job-ring is accessible from non
TrustZone.

Bit 15 (TrustZone) is the logical inverse of bit 3 hence the above value of
0x8001 shows that JROWN_NS=0 and TrustZone=1.

Clearly then as soon as TrustZone becomes active the job-ring registers are
no longer accessible from Linux, which is not what we want.

This patch explicitly sets all job-ring registers to JROWN_NS=1 (non
TrustZone) by default and to the Non-Secure MID 001. Both settings are
required to successfully assign a job-ring to non-secure mode. If a piece
of TrustZone firmware requires ownership of job-ring registers it can unset
the JROWN_NS bit itself.

This patch in conjunction with a modification of the Linux kernel to skip
HWRNG initialisation makes CAAM usable to Linux with TrustZone enabled.
Signed-off-by: NBryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Alex Porosanu <alexandru.porosanu@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Aneesh Bansal <aneesh.bansal@nxp.com>
Link: https://github.com/OP-TEE/optee_os/issues/1408
Link: https://tinyurl.com/yam5gv9aTested-by: NLukas Auer <lukas.auer@aisec.fraunhofer.de>

We should take the MX6DP and MX6QP options in consideration
in the I2C_PADS_INFO macro.

Based on a patch by Pierluigi Passaro <pierluigi.p@variscite.com>
Signed-off-by: NEran Matityahu <eran.m@variscite.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>

We should take the MX6DP and MX6QP options in consideration
when defining imx_iomux_v3_setup_pad().

Based on a patch by Pierluigi Passaro <pierluigi.p@variscite.com>
Signed-off-by: NEran Matityahu <eran.m@variscite.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>

The original text is from the time that the config options were not
converted to Kconfig.

After the conversion to Kconfig only CONFIG_SECURE_BOOT and
CONFIG_CMD_DEKBLOB need to be selected by the user.

The other config options are automatically selected by the Kconfig
logic.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: NBreno Lima <breno.lima@nxp.com>

The input keycode KEY_POWER is used in the imx6ull.dtsi file,
hence include the input header where used.
Signed-off-by: NStefan Agner <stefan.agner@toradex.com>

fastboot tool is a convenient way to flash the eMMC, so
add support for it.

Examples of usages:

On the mx6sabresd:

=> fastboot 0

On the Linux PC connected via USB:

$ sudo fastboot getvar bootloader-version -i 0x0525
bootloader-version: U-Boot 2018.01-00550-g7517cfe
finished. total time: 0.000s

$ sudo fastboot reboot -i 0x0525

(this causes the mx6sabresd to reboot)
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Tested-by: NShawn Guo <shawn.guo@linaro.org>

Select CONFIG_CMD_USB_MASS_STORAGE so that the 'ums' can be used.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>

Selecting CONFIG_USB_FUNCTION_MASS_STORAGE=y in the defconfig leads to
the following error:

cmd/built-in.o: In function `do_usb_mass_storage':
cmd/usb_mass_storage.c:217: undefined reference to `fsg_main_thread'
cmd/usb_mass_storage.c:170: undefined reference to `fsg_init'

CONFIG_USB_FUNCTION_MASS_STORAGE option is built only for
the non-SPL case as per the logic in drivers/usb/gadget/Makefile,
so remove the incorrect CONFIG_SPL ifdefery to fix the build
failure.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Tested-by: NShawn Guo <shawn.guo@linaro.org>

Add board specific imx config file with recommended IPU Qos settings
and adapted DDR configuration.
Signed-off-by: NSoeren Moch <smoch@web.de>

SION bit should be used in the situation that we need
to read back the value of a pin and should not be set by
default macro.

We get some malfunction as raised by following thread

https://www.spinics.net/lists/linux-usb/msg162574.html

As reported by this application note:
https://www.nxp.com/docs/en/application-note/AN5078.pdf

The software input on (SION) bit is an option to force an input
path to be active regardless of the value driven by the
corresponding module. It is used when the nature direction
of a pin depending on selected alternative function is an output,
but it is needed to read the real logic value on a pin.

The SION bit can be used in:
• Loopback: the module of a selected alternative function drives
the pad and also receives the pad value as an input
• GPIO capture: the module of a selected alternative function
drives the pin and the value is captured by the GPIO

SION bit is not necessary when the pin is configured as a peripheral
apart specific silicon bug. If an application needs to have this
set, this should be done in board file or in dts file
Signed-off-by: NMichael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: NBenoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Signed-off-by: NMichael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>

Enable UHS and HS200 for mx7dsabresd.

Read Speed improvement:
Kingston SD10VG2/16GB SDHC 3.0 card
22.2MB/s -> 73.7MB/s
eMMC5.0 MTFC8GACAEAM:
68MB/s -> 87MB/s
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>

Introduce SDR104 and HS200 support
The implementation takes linux kernel sdhci.c and sdhci-esdhc-imx.c
as reference.
 - Implement esdhc_change_pinstate to dynamically change pad settings
 - Implement esdhc_set_timing
 - Implement esdhc_set_voltage to switch voltage
 - Implement fsl_esdhc_execute_tuning to execute time process
 - Enlarge the cfg->f_max to 200MHz.
 - Parse fsl,tuning-step, fsl,tuning-start-tap and
   fsl,strobe-dll-delay-target from device tree.
 - Parse no-1-8-v property
 - Introduce esdhc_soc_data to indicate the flags and caps
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NJaehoon Chung <jh80.chung@samsung.com>

The pinmux and tuning settings are from
https://source.codeaurora.org/external/imx/linux-imx/tree/arch/
arm/boot/dts/imx7s.dtsi?h=imx_4.9.11_1.0.0_ga
https://source.codeaurora.org/external/imx/linux-imx/tree/arch/
arm/boot/dts/imx7d-sdb.dts?h=imx_4.9.11_1.0.0_ga

To support HS200 and SDR104, we need change pinmux settings dynamically.
And configure tuning step and start tuning tap, otherwise you may
see tuning failure.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>

Add entries that will be used for tuning control.
The whole layout not changed, just expand reserved3[84] and
rename other reservedx in sequence.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NJaehoon Chung <jh80.chung@samsung.com>

The board header file included a reference to the starting point
from nitrogen6x.h, but since so much changed, the file bears
little resemblance to that file.
Signed-off-by: NEric Nelson <eric@nelint.com>

The initial implementation of mx6memcal reset the CPU after
running the memory calibration procedure because the generic
board has no information about which boot devices are available.

Now that we have SDP support in SPL, use it to allow a full
U-Boot to be uploaded (i.e. to use "mtest").
Signed-off-by: NEric Nelson <eric@nelint.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>

This patch just changes the order of configuration items in
mx6memcal_defconfig to match the Kconfig layout, making it easier
to track changes made using menuconfig.
Signed-off-by: NEric Nelson <eric@nelint.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>

Static variables are not available during board_init_f().
'static uint32_t mx53_dram_size[2];' was used in board specific
dram_init(), dram_init_banksize() and get_effective_memsize() to avoid
multiple calls to get_ram_size().

Reused dram initialization functions from arch/arm/mach-imx/mx5/mx53_dram.c
Signed-off-by: NPatrick Bruenn <p.bruenn@beckhoff.com>

Static variables are not available during board_init_f().
'static uint32_t mx53_dram_size[2];' was used in board specific
dram_init(), dram_init_banksize() and get_effective_memsize() to avoid
multiple calls to get_ram_size().

Reused dram initialization functions from arch/arm/mach-imx/mx5/mx53_dram.c
Signed-off-by: NPatrick Bruenn <p.bruenn@beckhoff.com>

Move dram_init(), dram_init_banksize() and get_effective_memsize() to
arch/arm/mach-imx/mx5/mx53_dram.c, where it can be reused by m53evk and
mx53loco.
Signed-off-by: NPatrick Bruenn <p.bruenn@beckhoff.com>

Static variables are not available during board_init_f().
'static uint32_t mx53_dram_size[2];' was used in board specific
dram_init(), dram_init_banksize() and get_effective_memsize() to avoid
multiple calls to get_ram_size().

However multiple calls are better than undefined behavior...
This fixes:
https://lists.denx.de/pipermail/u-boot/2017-November/313214.html
https://lists.denx.de/pipermail/u-boot/2017-December/314480.htmlSigned-off-by: NPatrick Bruenn <p.bruenn@beckhoff.com>

Validate the time at startup:
 - in case rtc error add to kernel command line RTC_ERROR
 - clamp date to 1-Jan-2036
Signed-off-by: NNandor Han <nandor.han@ge.com>
Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>

The exact definition of a successful boot is defined by user-space.
Determine the boot partition automatically.  A partition is selected if
file `/boot/bootcause/firstboot' exists (meaning that the partition has
freshly installed software) OR if file `/boot/fitImage' exists.

When userspace determines that new software was successfully installed,
it must (1) delete `/boot/fitImage' on the _inactive_ partition and (2)
remove `/boot/bootcause/firstboot'.

Enable video, but do not display logos or other version information.
Silence kernel console logging by default.

Print a message to VGA screen in case of boot failure and reset bootcount
to allow the user to attempt boot again.
Signed-off-by: NIan Ray <ian.ray@ge.com>
Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>

Change the kernel command line to mount the root filesystem read-only in
order to be able to run filesystem check on it on boot.
Signed-off-by: NHannu Lounento <hannu.lounento@ge.com>
Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>

Enable bootcount using an EXT file.
Signed-off-by: NIan Ray <ian.ray@ge.com>
Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>

Read boot script from shared partition, if available.
Signed-off-by: NIan Ray <ian.ray@ge.com>
Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>

Modify configuration to support FIT. Set variable `confidx' from VPD,
in order to load the correct device tree. Modify/simplify U-Boot
environment to support loading FIT image.
Signed-off-by: NIan Ray <ian.ray@ge.com>
Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>

Enable the hardware watchdog on bx50v3 to cause it to reset in the event
the board hangs.

Configure GPIO_9 pin as WDOG1_B so that a watchdog timeout results in a
full system reset.

The watchdog is used and reconfigured by systemd approximately 1.7 seconds
into boot. Adding a few seconds for U-Boot and a few more seconds as a
safety margin.

Note that the PCIe controller is _not_ put back into a safe state prior
to board reset.  This is a problem if board reset is implemented as CPU
reset.
Signed-off-by: NIan Ray <ian.ray@ge.com>
Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>