- 19 2月, 2019 1 次提交
-
-
由 Peng Ma 提交于
Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls208xardb and ls208xaqds defconfigs that missing one of them or more. enable CONFIG_DM_MMC for some defconfigs to support CONFIG_BLK Support sata for all ls208xa defconfigs Signed-off-by: NPeng Ma <peng.ma@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
- 08 1月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 25 10月, 2018 1 次提交
-
-
由 Jeremy Gebben 提交于
The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: NJeremy Gebben <jgebben@sweptlaser.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 20 10月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 27 9月, 2018 1 次提交
-
-
由 Yinbo Zhu 提交于
This enables the folowing to Kconfig: CONFIG_BLK CONFIG_DM_MMC Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 04 9月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 18 8月, 2018 2 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: NAdam Ford <aford173@gmail.com> Acked-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 17 8月, 2018 1 次提交
-
-
由 Tom Rini 提交于
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 22 7月, 2018 1 次提交
-
-
由 Adam Ford 提交于
Some boards indicate support from booting NAND or ONENAND booting, but don't enable the CONFIG_NAND. This makes those boards imply NAND which will make enabling other flags that are dependent on CONFIG_NAND possible and easier to migrate. Signed-off-by: NAdam Ford <aford173@gmail.com>
-
- 11 7月, 2018 1 次提交
-
-
This patch moves CONFIG_MP to Kconfig Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 04 6月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 09 4月, 2018 1 次提交
-
-
由 Mario Six 提交于
Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
- 08 4月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 16 3月, 2018 1 次提交
-
-
由 Tom Rini 提交于
This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 11 2月, 2018 1 次提交
-
-
由 Tom Rini 提交于
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 18 11月, 2017 1 次提交
-
-
由 Tom Rini 提交于
We first introduce CONFIG_USE_BOOTCOMMAND, similar to CONFIG_USE_BOOTARGS. We then migrate CONFIG_BOOTCOMMAND for most CONFIG_DISTRO_DEFAULT users. In some cases platforms have a complex scheme around this usage, and these have been defered for the moment so that platform maintainers can work on a migration plan. Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NLukasz Majewski <lukma@denx.de>
-
- 11 10月, 2017 1 次提交
-
-
由 Tuomas Tynkkynen 提交于
Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
-
- 28 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 15 8月, 2017 2 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Sam Protsenko 提交于
Also introduce CONFIG_USE_BOOTARGS option so we can control if CONFIG_BOOTARGS defined at all. Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org> [trini: Resync r8a779[56]_ulcb, various ls10xx targets] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 12 8月, 2017 2 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_NAND Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Sync up a few more, add imply's] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_PCI Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
- 09 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Reviewed-by: NJoe Hershberger <joe.hershberger@ni.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 08 8月, 2017 1 次提交
-
-
由 Alexandru Gagniuc 提交于
Signed-off-by: NAlexandru Gagniuc <alex.g@adaptrum.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 01 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the defconfig files. Tested-by: NAdam Ford <aford173@gmail.com> Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
- 26 7月, 2017 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 19 6月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 02 6月, 2017 1 次提交
-
-
由 Santan Kumar 提交于
Add CONFIG_NAND_BOOT config flag to organise NAND_BOOT specific code in config flag like -nand-boot specfic errata errata_rcw_src() -CONFIG_SYS_NAND_U_BOOT_DST,etc Signed-off-by: NSantan Kumar <santan.kumar@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com> Signed-off-by: NAbhimanyu Saini <abhimanyu.saini@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 22 5月, 2017 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_EEPROM CONFIG_CMD_EEPROM_LAYOUT CONFIG_EEPROM_LAYOUT_HELP_STRING Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com> [trini: Rework Kconfig logic slightly, define EEPROM location on TI eval platforms] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 01 5月, 2017 1 次提交
-
-
由 Chris Packham 提交于
Signed-off-by: NChris Packham <judge.packham@gmail.com> [trini: default y if DM_RTC, re-sync] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 18 4月, 2017 1 次提交
-
-
由 York Sun 提交于
Use CONFIG_ARCH_LS2080A instead. Signed-off-by: NYork Sun <york.sun@nxp.com>
-
- 14 3月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 10 3月, 2017 1 次提交
-
-
由 Tom Rini 提交于
In some cases this is absolutely required, so select this for some secure features. This also requires migration of RSA_FREESCALE_EXP Cc: Ruchika Gupta <ruchika.gupta@nxp.com> Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com> Cc: Naveen Burmi <NaveenBurmi@freescale.com> Cc: Po Liu <po.liu@freescale.com> Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com> Cc: Priyanka Jain <Priyanka.Jain@freescale.com> Cc: Sumit Garg <sumit.garg@nxp.com> Cc: Shaohui Xie <Shaohui.Xie@freescale.com> Cc: Chunhe Lan <Chunhe.Lan@freescale.com> Cc: Feng Li <feng.li_2@nxp.com> Cc: Alison Wang <alison.wang@freescale.com> Cc: Mingkai Hu <Mingkai.Hu@freescale.com> Cc: York Sun <york.sun@nxp.com> Cc: Saksham Jain <saksham.jain@nxp.freescale.com> Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 13 2月, 2017 1 次提交
-
-
由 Masahiro Yamada 提交于
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is not completed. Finish this work by the tool. During this move, let's rename it to CONFIG_MTD_NOR_FLASH. Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH" than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will make the code more readable. Besides, negative meaning symbols do not fit in obj-$(CONFIG_...) style Makefiles. This commit was created as follows: [1] Edit "default n" to "default y" in the config entry in common/Kconfig. [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH" [3] Rename the instances in defconfigs by the following: find . -path './configs/*_defconfig' | xargs sed -i \ -e '/CONFIG_SYS_NO_FLASH=y/d' \ -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/' [4] Change the conditionals by the following: find . -name '*.[ch]' | xargs sed -i \ -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \ -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \ -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \ -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/' [5] Modify the following manually - Rename the rest of instances - Remove the description from README - Create the new Kconfig entry in drivers/mtd/Kconfig - Remove the old Kconfig entry from common/Kconfig - Remove the garbage comments from include/configs/*.h Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
- 28 1月, 2017 1 次提交
-
-
由 Patrick Delaunay 提交于
We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly update all of the config files we must also update CMD_PART and CMD_GPT to also be in Kconfig in order to avoid complex logic elsewhere to update all of the config files. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Signed-off-by: NPatrick Delaunay <patrick.delaunay73@gmail.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 24 1月, 2017 1 次提交
-
-
由 Tom Rini 提交于
This option should not really be user selectable. Note that on PowerPC we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be conditional on that. Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
-
- 22 1月, 2017 1 次提交
-
-
由 Jagan Teki 提交于
Cc: Tom Rini <trini@konsulko.com> Signed-off-by: NJagan Teki <jagan@openedev.com>
-
- 19 1月, 2017 1 次提交
-
-
由 Minghuan Lian 提交于
The patch enables PCIe in ls2080a defconfigs and removes unused PCIe related macro defines. Signed-off-by: NMinghuan Lian <Minghuan.Lian@nxp.com> Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 05 1月, 2017 1 次提交
-
-
由 York Sun 提交于
Create driver/ddr/fsl/Kconfig and move existing options. Clean up existing macros. Signed-off-by: NYork Sun <york.sun@nxp.com> [trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s] Signed-off-by: NTom Rini <trini@konsulko.com>
-