As we use the driver model for ESDHC there is no need
for defining CONFIG_SYS_FSL_USDHC_NUM and CONFIG_SYS_FSL_ESDHC_ADDR,
so simply remove them.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>

Currently the following build warning is seen:

===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
===================================================

Since the mx7ulp-evk board does not have networking support, explicitly
disable networking.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>

Xilinx/FPGA changes for v2020.04

ARM64:
- Add INIT_SPL_RELATIVE dependency

SPL:
- FIT image fix
- Enable customization of bl2_plat_get_bl31_params()

Pytest:
- Add test for octal/hex conversions

Microblaze:
- Fix manual relocation for one SPI instance

Nand:
- Convert zynq/zynqmp drivers to DM

Xilinx:
- Enable boot script location via Kconfig
- Support OF_SEPARATE in board FDT selection
- Remove low level uart setup it is done later by code
- Add support for DEVICE_TREE variable passing for SPL

Zynq:
- Enable jtag boot mode via distro boot
- Removing unused baseaddresses from hardware.h
- DT fixups

ZynqMP:
- Fix emmc boot sequence
- Simplify spl logic around bss and board_init_r()
- Support psu_post_config_data() calling
- Tune mini-nand DTS
- Fix psu wiring for a2197 boards
- Add runtime MMC device boot order filling in spl
- Clear ATF handoff handling with custom bl2_plat_get_bl31_params()
- Add support u-boot.its generation
- Use single image configuration for all platforms
- Enable PANIC_HANG via Kconfig
- DT fixups
- Firmware fixes
- Add support for zcu208 and zcu1285

Versal:
- Fix emmc boot sequence
- Enable board_late_init() by default

- MediaTek improvements
- Some generic clk improvements
- A few assorted bugfixes

This patch add CONFIG_TARGET_MT7623 into mt7623n_bpir2_defconfig
to fix the mt7623 compile error after building others mediatek target
platform
Signed-off-by: NSam Shih <sam.shih@mediatek.com>
Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>

This patch move u-boot properties to -u-boot.dtsi file.
Signed-off-by: NSam Shih <sam.shih@mediatek.com>
Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>

This adds a general board file based on MT7622 SoCs from MediaTek.
This commit is adding the basic boot support for the MT7622 rfb.
Signed-off-by: NSam Shih <sam.shih@mediatek.com>
Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>
Tested-by: NFrank Wunderlich <frank-w@public-files.de>

This patch add mmc and sd support for Mediatek MT7622 SoCs
Signed-off-by: NSam Shih <sam.shih@mediatek.com>
Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>

This patch add power domain support for Mediatek MT7622 SoCs
Signed-off-by: NRyder Lee <ryder.lee@mediatek.com>
Signed-off-by: NSam Shih <sam.shih@mediatek.com>

This patch fix clock-rate overflow problem in mediatek
clock driver common part.
Signed-off-by: NSam Shih <sam.shih@mediatek.com>
Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>

This patch add clock driver for MediaTek MT7622 SoC.
Signed-off-by: NRyder Lee <ryder.lee@mediatek.com>
Signed-off-by: NSam Shih <sam.shih@mediatek.com>

Due to the pinctrl hardware of MT7622 is difference from others
SoC which using the common part of mediatek pinctrl.
So we need to modify the common part of mediatek pinctrl.
Signed-off-by: NSam Shih <sam.shih@mediatek.com>
Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>

This patch add Pinctrl driver for MediaTek MT7622 SoC.
Signed-off-by: NSam Shih <sam.shih@mediatek.com>
Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>

Add support for MediaTek MT7622 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: NSam Shih <sam.shih@mediatek.com>
Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>

If make the ref clock optional, no need refer to fixed-clock when
the ref clock is always on or comes from oscillator directly.
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>

No need check -ENOSYS anymore after add dummy_enable() for
fixed-clock.
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>

This is used to avoid clk_enable() return -ENOSYS.
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>

Sometimes we may need get (optional) clock without a device,
that means use ofnode.
e.g. when the phy node has subnode, and there is no device created
for subnode, in this case, we need these new APIs to get subnode's
clock.
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>

Add valid check for clk->dev, it's useful when get optional
clock even when the clk point is valid, but its dev will be
NULL.
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>

If skip all return error number, it may skip some real error cases,
so only skip the error when the clock is not provided in DTS
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>

The SSUSB IP's clocks come from ssusbsys module on mt7629,
so add its driver
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>

This adds a general board file based on MT8512 SoCs from MediaTek.

Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.

This commit is adding the basic boot support for the MT8512 eMMC board.
Signed-off-by: Nmingming lee <mingming.lee@mediatek.com>

For CMD21 tuning data, the 128/64 bytes data may coming in very
short time, before msdc_start_data(), the read data has already
come, in this case, clear MSDC_INT will cause the interrupt disappear
and lead to the thread hang.

the solution is just clear all interrupts before command was sent.
Signed-off-by: Nmingming lee <mingming.lee@mediatek.com>

This patch adds mmc support for MediaTek MT8512/MT8110 SoCs.
MT8512/MT8110 SoCs puts the tune register at top layer, so
need add new code to support it.
Signed-off-by: Nmingming lee <mingming.lee@mediatek.com>

Add Pinctrl driver for MediaTek MT8512 SoC.
Signed-off-by: Nmingming lee <mingming.lee@mediatek.com>

Add configurable pcw_chg_reg/ibits/fmin to mtk_pll to support mt8512

Add new set_clr_upd mux type and related operation to
mtk common clock driver to support mt8512

Add clock driver for MediaTek MT8512 SoC, include topckgen,
apmixedsys and infracfg support.
Signed-off-by: Nmingming lee <mingming.lee@mediatek.com>

Add support for MediaTek MT8512 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: Nmingming lee <mingming.lee@mediatek.com>

Sam doesn't work for Linaro anymore, so Linaro mail is not valid. Change
it to his home mail instead.
Signed-off-by: NSam Protsenko <joe.skb7@gmail.com>

When no partition table is found, users should be warned so.
Warning that no device is available in this case could be misleading,
especially as it is the same error when no device is selected.
Signed-off-by: NAlexandre Besnard <alexandre.besnard@softathome.com>

The device tree compiler expects that a node with a unit-address has a reg
property.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Some features implicitly depended on MALLOC_F and OF_LIBFDT and would
fail at link-time if these features were not enabled.
Signed-off-by: NSean Anderson <seanga2@gmail.com>

asm-generic/sections.h references ulong but does not include
linux/types.h
Signed-off-by: NSean Anderson <seanga2@gmail.com>

Add stub for dma_memcpy() and dma_get_device when CONFIG_DMA is
disabled. This avoids ifdefs in driver code using DMA APIs
Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMA. This allows to use
macros such as CONFIG_IS_ENABLED() that allow conditional compilation of
code for SPL and U-Boot.
Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Pull request for UEFI sub-system for efi-2020-04-rc1-2

Bug fixes for the UEFI sub-system are provided:

* imply VIDEO_ANSI for correct cursor positioning and colors
* fix issues in the UEFI block device driver
* add missing documentation

-----------------------------------
- imx8:
	add capricorn giedi deneb boards
- imx6:
	fixed fow wandboard
- imx7: DM_ETHER for pico-imx7d
- fsl_esdhc_imx: add broken-cd property
- New SOC: IMXRT10xx

Travis:
	https://travis-ci.org/sbabic/u-boot-imx/builds/637126531

- Important bugfix for some Tegra platforms

UEFI programs like GRUB make change terminal colors which requires support
for ANSI escape sequences.

Let CONFIG_EFI_LOADER=y imply CONFIG_VIDEO_ANSI.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>