- 21 3月, 2009 2 次提交
-
-
由 Jon Smirl 提交于
Add .gitignore for generated files in api_examples directory Signed-off-by: NJon Smirl <jonsmirl@gmail.com> Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Nobuhiro Iwamatsu 提交于
sh_eth_reset is function to reset Ether IP. The MAC address is stored in IP, but it is initialized by this function. OS (e.g. Linux Kernel) can not use this device when initialized. This revises this problem. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
-
- 20 3月, 2009 1 次提交
-
-
由 Anatolij Gustschin 提交于
PCI outbound address map configuration doesn't match the PCI memory address range covered by appropriate TLB entry configuration for canyonlands causing machine check exceptions while accessing PCI memory regions. This patch provides a fix for this issue. Kazuaki Ichinohe observed and reported this issue while testing display output with PCI ATI video card on canyonlands. Signed-off-by: NAnatolij Gustschin <agust@denx.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
- 19 3月, 2009 10 次提交
-
-
由 Richard Retanubun 提交于
Follow up to the flash_fixup_stm to fix geometry reversal on STMicro M29W320ET flash chip. The M29W320DT has 4 erase region. Signed-off-by: NRichard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Mike Frysinger 提交于
The smc911x driver changed the naming convention for its register funcs, so update the eeprom code accordingly. Signed-off-by: NMike Frysinger <vapier@gentoo.org> CC: Ben Warren <biggerbadderben@gmail.com>
-
由 Grzegorz Bernacki 提交于
Total5200 and digsy MTC use I2C port 2 pins as a ATA chip select. To avoid adding board-specific ifdefs to cpu/mpc5xxx/ide.c new define CONFIG_SYS_ATA_CS_ON_I2C2 was introduced. It is used by Total5200 and will be used by digsy MTC and other boards with ATA CS on I2C pins. Signed-off-by: NGrzegorz Bernacki <gjb@semihalf.com>
-
由 Heiko Schocher 提交于
This patch adds support for the kmsupx4 board from Keymile, based on a Freescale MPC852T CPU - serial console on SMC1 - 32 MB SDRAM - 32 MB NOR Flash - Ethernet over SCC3 - I2C Bitbang Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
renaming the "mgsuvd" board port into "km8xx", because there come more similar boards from keymile. Compiling the mgsuvd board with "make mgsuvd_config" remains. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
- added to keymile-common.h: - bootcount support - COMMAND HISTORY - CONFIG_AUTO_COMPLETE - CONFIG_SYS_FLASH_PROTECTION - JFFS2 support - CONFIG_VERSION_VARIABLE - extracted common I2C settings for all boards - common default environment settings summarized Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
with the new CONFIG_SYS_DELAYED_ICACHE config option, ICache is not enabled before code runs from RAM. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
Size of one environment sector is 0x20000. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Ladislav Michl 提交于
Fix indentation broken by symbol renames. "Sort" driver related definitons. Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
-
- 18 3月, 2009 10 次提交
-
-
-
-
由 TsiChung Liew 提交于
Signed-off-by: NTsiChung Liew <Tsi-Chung.Liew@freescale.com>
-
由 TsiChung Liew 提交于
The Nand flash was unable to read and write properly due to Nand Chip Select (nCE) setup was in reverse order. Also, increase the Nand time out value to 60. Signed-off-by: NTsiChung Liew <Tsi-Chung.Liew@freescale.com>
-
由 TsiChung Liew 提交于
Update PLATFORM_CPPFLAGS to accept 4.3.x version of ColdFire compiler. Signed-off-by: NTsiChung Liew <Tsi-Chung.Liew@freescale.com>
-
由 TsiChung Liew 提交于
Default gzip bootm size is 8MB. Some platforms require more than 8MB Signed-off-by: NTsiChung Liew <Tsi-Chung.Liew@freescale.com>
-
由 TsiChung Liew 提交于
The serial boot dram extended/standard mode register was not setup and was using default DRAM setup causing the U-boot was unstable to boot up in serial mode. Signed-off-by: NTsiChung Liew <Tsi-Chung.Liew@freescale.com>
-
由 arun c 提交于
According to coldfire manual data timeout > address time out also use correct macro to program XARB_CFG Signed-off-by: NArun C <arunedarath@mistralsolutions.com>
-
由 Scott Wood 提交于
This was intended to happen before, but a trivial bug prevented it. Signed-off-by: NScott Wood <scottwood@freescale.com>
-
由 Ladislav Michl 提交于
nboot command currently does not skip bad blocks and gives read error when loading image stored over bad block. With patch applied, nboot works as expected: Device 0 bad blocks: 00780000 014a0000 02000000 02cc0000 04aa0000 Loading from NAND 128MiB 3,3V 8-bit, offset 0x2c00000 Image Name: Linux-2.6.22-omap1 Created: 2008-11-20 23:44:32 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1052520 Bytes = 1 MB Load Address: 10008000 Entry Point: 10008000 Skipping bad block 0x02cc0000 Automatic boot of image at addr 0x10400000 ... ... Signed-off-by: NLadislav Michl <ladis@linux-mips.org> Signed-off-by: NScott Wood <scottwood@freescale.com>
-
- 17 3月, 2009 3 次提交
-
-
由 Stefan Roese 提交于
This patch fixes a problem spotted by Mikhail Zolotaryov on Sequoia with the DDR2 configuration to only use one CS (rank). As this code is most likely copied from the original Sequoia version, this error was copied as well. This patch also removes some dead code. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
This patch fixes a problem spotted by Mikhail Zolotaryov on Sequoia with the DDR2 configuration to only use one CS (rank). As this code is most likely copied from the original Sequoia version, this error was copied as well. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Mikhail Zolotaryov 提交于
Sequoia board schematics (DES0211_11_SCH_11.pdf, page 5, unit U1D) specifies that BankSel#1 is not connected, while bootloader memory configuration is (board/amcc/sequoia/sdram.c): mtsdram(DDR0_10, 0x00000300); i.e. both Chip Selects used - not correct. If we change to correct value here: mtsdram(DDR0_10, 0x00000100); memory is accessible OK also. Signed-off-by: NMikhail Zolotaryov <lebon@lebon.org.ua> Signed-off-by: NStefan Roese <sr@denx.de>
-
- 16 3月, 2009 5 次提交
-
-
由 Wolfgang Denk 提交于
Update CHANEGLOG, fix minor coding style issue. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
-
-
-
-
- 15 3月, 2009 2 次提交
-
-
由 Jerry Van Baren 提交于
The routine assumed 4 bank SDRAMs, enhance to configure for 4 or 8 bank SDRAMs. Signed-off-by: NGerald Van Baren <vanbaren@cideas.com> Acked-by: NDave Liu <daveliu@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Norbert van Bolhuis 提交于
This patch makes sure the correct mask is applied when setting the encryption and I2C bus 0 clock in SCCR. Failing to do so may lead to ENCCM being 0 in which case I2C bus 0 won't function. Signed-off-by: NNorbert van Bolhuis <nvbolhuis@aimvalley.nl> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
- 14 3月, 2009 1 次提交
-
-
由 Dirk Behme 提交于
Read and store OMAP3 die ID in U-Boot environment. Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
- 13 3月, 2009 2 次提交
-
-
由 Jon Smirl 提交于
Set a non-zero speed in the MII register so that MII commands will work. Signed-off-by: NJon Smirl <jonsmirl@gmail.com>
-
由 Yusuke.Goda 提交于
Signed-off-by: NYusuke Goda <goda.yusuke@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
- 12 3月, 2009 4 次提交
-
-
由 Yoshihiro Shimoda 提交于
The rtl8139 driver use pci_mem_to_phys. So it need PCI system memory registration. Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Yoshihiro Shimoda 提交于
We can built 'make sh7785lcr_32bit_config'. And add new command "pmb" for this mode. This command changes PMB for using 512MB system memory. Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Yoshihiro Shimoda 提交于
Some register value was hardcoded for System memory size 128MB and memory offset 0x08000000. This patch fixed the problem. Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-